Denon-MC2000-mix-sm维修电路图 手册.pdf

SERVICE MANUAL D&M Holdings Inc. MODELJPE3E2EKEAE1E1KE1C MC2000PPP DJ Controller Ver. 3 S0620-0V03DM/DG1302 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fail. For purposes of improvement, specifications and design are subject to change without notice. Please refer to the MODIFICATION NOTICE. RadioFans.CN 2 CONTENTS SAFETY PRECAUTIONS .3 NOTE FOR SCHEMATIC DIAGRAM .4 TECHNICAL SPECIFICATIONS .5 DIMENSION .5 DISASSEMBLY .6 SPECIAL MODE .12 1. Special mode setting .12 2. Version Up mode .12 3. Version indicate mode .13 4. Adjusting mode of the touch sense sensitivity .14 5. Initialization of parameters .14 6. Adjusting interval time of MIDI command transmission .15 7. SW, VOLUME, ENCODER and LED TEST .16 WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE .23 PROCEDURE FOR UPGRADING THE VERSION OF THE FIRMWARE .23 TROUBLE SHOOTING .32 WIRING DIAGRAM .41 BLOCK DIAGRAM .43 POWER BLOCK DIAGRAM .44 Level DIAGRAM .45 PRINTED WIRING BOARDS .46 CONTROL .46 I/O .48 SCHEMATIC DIAGRAMS (1/2) .50 CONTROL UNIT .50 I/O UNIT .51 EXPLODED VIEW .52 PARTS LIST OF EXPLODED VIEW .53 PACKING VIEW .55 PARTS LIST OF PACKING & ACCESSORIES .55 SEMICONDUCTORS .57 1. ICs .57 PARTS LIST OF P.C.B. UNIT .68 CONTROL P.C.B ASSY .68 I/O P.C.B ASSY.71 CROS FADER P.C.B ASSY .75 PHONE P.C.B ASSY.75 RadioFans.CN 3 SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. Be sure to test for leakage current with the AC plug in both polarities, in addition, when the sets power is in each state (on, off and standby mode), if applicable. CAUTION Please heed the following cautions and instructions during servicing and inspection. Heed the cautions! Cautions which are delicate in particular for servicing are labeled on the cabinets, the parts and the chassis, etc. Be sure to heed these cautions and the cautions described in the handling instructions. Cautions concerning electric shock! (1) An AC voltage is impressed on this set, so if you touch internal metal parts when the set is energized, you may get an electric shock. Avoid getting an electric shock, by using an isolating transformer and wearing gloves when servicing while the set is energized, or by unplugging the power cord when replacing parts, for example. (2) There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly! Through great care is taken when parts were manufactured from sheet metal, there may be burrs on the edges of parts. The burrs could cause injury if fingers are moved across them in some rare cases. Wear gloves to protect your hands. Use only designated parts! The sets parts have specific safety properties (fire resistance, voltage resistance, etc.). Be sure to use parts which have the same properties for replacement. The burrs have the same properties. In particular, for the important safety parts that are indicated by the z mark on schematic diagrams and parts lists, be sure to use the designated parts. Be sure to mount parts and arrange the wires as they were originally placed! For safety seasons, some parts use tapes, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires by arranging them and using clamps to keep them away from heating and high voltage parts, so be sure to set everything back as it was originally placed. Make a safety check after servicing! Check that all screws, parts and wires removed or disconnected when servicing have been put back in their original positions, check that no serviced parts have deteriorate the area around. Then make an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and on the power. Using a 500V insulation resistance tester, check that the insulation resistance value between the inplug and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired. Many of the electric and the structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and the use of replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and the parts list in this service manual. Be sure to replace them with the parts which have the designated part number. (1) Schematic diagrams .Indicated by the z mark. (2) Parts lists .Indicated by the z mark. The use of parts other than the designated parts could cause electric shocks, fires or other dangerous situations. CAUTION Concerning important safety parts RadioFans.CN 4 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DO NOT return the set to the customer unless the problem is identified and remedied. NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO FARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts indicated by nsp on this table cannot be supplied. When ordering a part, make a clear distinction between 1 and I (i) to avoid mis-supplying. A part ordered without specifying its part number can not be supplied. General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) Part indicated by mark is not illustrated in the exploded view. WARNING: 1. 2. 3. 4. 5. 6. NOTE FOR PARTS LIST RadioFans.CN 5 TECHNICAL SPECIFICATIONS DIMENSION n Audio (0 dBu=0.775 Vrms, 0 dBV =1 Vrms) LINE inputs1 Stereo Unbalanced RCA terminal Input impedance:10 k Level:0 dBV Signal to Noise ratio:Over 82 dB Microphone inputs1 Monaural Microphone :Balanced 1/4 in. TRS terminal (Tip: hot, Ring: cold, Sleeve: ground) Input impedance:10 k Level:48 20 dBu (Unity = 40 dBu) USB AUDIO inputs2 Stereo (4 Monaural) 16 bit, Fs: 48 kHz USB B MASTER output Unbalanced:Stereo RCA terminal Load impedance:10 k Level:2.55 dBV (Max +10dBV) Frequency response:20 Hz 20 kHz (1 dB) THD:Less than 0.05 % Crosstalk:Less than 85 dB (1 kHz) Headphone outputStereo 1/4 in. (1 mm) Load impedance:40 Level:Over 50 mW n General USB MIDI input/output:IN: 1ch, OUT: 1ch MIDI 1.0, USB B Channel fader: PPM 7 Point LED 20 +10 dB, Peak CH fader: 45 mm slim type fader Cross fader: 45 mm fader Power supply voltage:5 V (USB Bus Power) Power consumption:500 mA Operating temperature: +5 C +35 C Operating humidity:25 % 85 % Storage temperature:20 C +60 C 400mm 10.6mm 11.5mm 50.0mm 240.0mm 4.6mm RadioFans.CN 6 DISASSEMBLY Disassemble in order of the arrow in the following figure. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe attention of assembling. If wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. Bottom BASE Refer to DISASSEMBLY 2. BOTTOM BASE and EXPLODED VIEW I/O PCB ASSY Refer to DISASSEMBLY 11-4. I/O PCB ASSY and EXPLODED VIEW I/O PCB ASSY (Ref. No. of EXPLODED VIEW : 6) PHONE PCB ASSY Refer to DISASSEMBLY 3. PHONE PCB ASSY and EXPLODED VIEW PHONE PCB ASSY (Ref. No. of EXPLODED VIEW : 8) TOP PANEL ASSY Refer to DISASSEMBLY 4. TOP PANEL ASSY and EXPLODED VIEW TOP PANEL ASSY (Ref. No. of EXPLODED VIEW : 2) WHEEL ASSY Refer to DISASSEMBLY 10. WHEEL ASSY and EXPLODED VIEW WHEEL ASSY (Ref. No. of EXPLODED VIEW : 3) CROSS FADER PCB ASSY Refer to DISASSEMBLY 6. CROSS FADER PCB ASSY and EXPLODED VIEW CROSS FADER PCB ASSY (Ref. No. of EXPLODED VIEW : 5) CONTROL PCB ASSY / SOFT KNOB Refer to DISASSEMBLY 5. CONTROL PCB ASSY / SOFT KNOB and EXPLODED VIEW CONTROL PCB ASSY (Ref. No. of EXPLODED VIEW : 7) BUTTON Refer to EXPLODED VIEW RadioFans.CN 7 1.Dismantle the packaging, taking out the machine . 2. Remove the screws form bottom base . 3. Disconnect the FCC cable,then remove the panel from bottom base . 1 2 3 4 7 8 5 6 11 12 13 14 絲*14 602-XM610-522 9 10 CONTROL PCB I/O PCB Remove the FFC cable from I/O PCB(REF NO.CN300A) SCREW *14 CN300A RadioFans.CN 8 4.Remove the rotary knob *20 and push knob*5 from panel . 5.Remove the screws *14 from panel . 6-1. Remove the nuts*20 and washer *20 from panel . 6-2. Remove the screws *2 from crossfader pcb assy . 1 602-HP1010K-182 絲*14 2 6 5 3 4 10 9 7 8 14 13 12 11 面板 (各20P.S.) 602-PTF3010-585 絲*2 鎖付VR之母與墊圈 Screw *14 panel Nut *20 Washer *20 Screw *2 RadioFans.CN 9 7-1.Remove the screws *21 from control pcb assy . 7-2.Remove the ground plates *6 and the screws*6 . 8. Remove the solder *2 ,then remove the control pcb assy . 9.Remove the square buttons and rotary buttons . SOLDER* RadioFans.CN 10 10-1.Remove the wheel assy*2 . 10-2. Remove the spring & wire assy *2 . 11-1. Remove the screws *7 from the bottom base. 11-2. Remove the nut *2 and washer *2 from phone jack. 11-3. Remove the rotary knob(small) *2 . E-RING RadioFans.CN 11 11-4. Remove the screws *4 from I/O pcb assy, then remove the I/O pcb assy . 602-QMX2BPM-322 自攻絲*2 602-B300-041 絲*2 I/O基板整組 Screw *2 Screw *2 I/O pcb assy RadioFans.CN 12 SPECIAL MODE 1. Special mode setting Turns on MC3000 while pressing buttons A, B and C. ModeABCContents Version Up mode246Firmware Upgrade Version indicate mode146Firmware version display Adjusting mode of the touch sense sensitivity345Adjust sensitivity of JOG wheel. Initialize mode245, 6Return to factory default setting. MIDI transmission time mode147MIDI command transmission interval time SW, VOLUME, ENCODER and LED TEST-Test of each function. (Use PC) ALL LED ON24SEL.All LED turn on 2. Version Up mode Version up processing z Refer to PROCEDURE FOR UPGRADING THE VERSION OF THE FIRMWARE for the procedure of the firmware update. (Refer to 23 page.) 12 34765 RadioFans.CN 13 3. Version indicate mode Confirmation of version Pressing (SHIFT+BROWSE1+FWD) at the same time, then connect MC2000 to a PC for confirmation of F/W version. How to read the version number Firmware Version LED (Ver A.XYZ. After Ver1.000, it is commercial version). A : LEFT DECK (for commercial version No.) X, Y, Z : RIGHT DECK 123456789 A (LEFT DECK)FX1-1FX1-2FX1-3LOOP INLOOP OUTAUTOHOT CUE 1HOT CUE 2HOT CUE 3 X (RIGHT DECK)FX2-1FX2-2FX2-3- Y (RIGHT DECK)LOOP INLOOP OUTAUTO- Z (RIGHT DECK)HOT CUE 1HOT CUE 2HOT CUE 3HOT CUE 4SYNCCUEPLAYVINYL MODE- Example : Ver1.132 DECK A side : FX1-1 DECK B side : FX2-1, LOOP IN, LOOP OUT, AUTO, HOT CUE 1, HOT CUE 2 Seven places of LED turns on. Press SHIFT to return to normal mode. 123 45 89 6 7 6 5 7 8 1234 123 123 A: The 1st digit numeric display. X: The 2nd digit numeric display. Y: The 3rd digit numeric display. Z: The 3rd digit numeric display. RadioFans.CN 14 4. Adjusting mode of the touch sense sensitivity The unit can control the sensitivity of the touch sensor for the Jog Wheel in 9 steps (-4 to 0 to +4). “-4” is the lowest sensitivity, and “+4” is the highest sensitivity. The default setting is “0”. (1) Pressing (SHIFT+LOAD A+LOAD B) at the same time, then connect MC2000 to a PC. (2) Press CUE, and switch the jog wheel that you want to adjust. (e.g.) If you press CUE of the left side, onl