Yamaha-VS-10-Service-Manual电路原理图.pdf

VS-10/NX-SW10 Home Theater System VS-10 Front Speaker NX-VS10M Rear Speaker NX-VS10E Rear Speaker NX-VS10E Center Speaker NX-VS10C NX-SW10 is composed of SW-VS10, NX-VS10C and NX-VS10E. VS-10 is composed of VS-10 and NX-VS10M. Front Speaker NX-VS10M Subwoofer SW-VS10 SERVICE MANUAL HOME THEATER SYSTEM VS-10/NX-SW10 100733 I CONTENTS TO SERVICE PERSONNEL . 1 REMOTE CONTROL TRANSMITTER PANELS. 1 FRONT/REAR PANELS . 24 SPECIFICATIONS. 5 DIMENSIONS . 6 INTERNAL VIEW . 7 VS-10 DISASSEMBLY PROCEDURES . 7 P. C. B. OPERATION CHECK. 8 SW-VS10 DISASSEMBLY PROCEDURES . 9 TEST PROGRAM MODE (VS-10) . 1011 DSP DIAG MODE (Self-diagnosis) . 1218 IC DATA . 1925 BLOCK DIAGRAM. 2629 PRINTED CIRCUIT BOARD . 3041 SCHEMATIC DIAGRAM . 4246 PARTS LIST. 4763 DISPLAY DATA . 64 REMOTE CONTROL TRANSMITTER . 6566 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. VS-10/NX-SW10 P.O.Box 1, Hamamatsu, Japan VS-10/NX-SW10 1 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA- SON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. I TO SERVICE PERSONNEL 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. I REMOTE CONTROL TRANSMITTER PANELS U, C, A modelsB, G models VS-10/NX-SW10 2 I FRONT/REAR PANELS G VS-10 U, C models A model VS-10/NX-SW10 3 B, G model G NX-VS10M G SW-VS10 (Subwoofer) U, C models VS-10/NX-SW10 4 A modelB, G model G NX-VS10C (Center Speaker)G NX-VS10E (Rear Speaker) VS-10/NX-SW10 5 I SPECIFICATIONS I VS-10 (Center Unit) G Audio Section Minimum RMS Output Power per Channel 1kHz, 10% THD, 625W + 25W Signal to Noise Ratio (IHF-A-Network) VIDEO190dB Total Harmonic Distortion (1kHz, 10W/6) VIDEO10.07% Input Sensitivity / Impedance VIDEO1200mV / 50k G Video Section Signal Level 1V p-p / 75 G General Power Supply U, C modelsAC120V, 60Hz B, G modelsAC230V, 50Hz A modelAC240V, 50Hz Power Consumption 60W Standby Power Consumption Reference data5.5W Dimensions (W x H x D) Only VS-10302 x 82 x 300mm (11-7/8 x 3-1/4 x 11-13/16) Setting Vertically (Include Stand and Pads)124 x 302.5 x 300mm (4-7/8 x 11-15/16 x 11-13/16) Setting Horizontally (Include Pads)302 x 88.5 x 300mm (11-7/8 x 3-1/2 x 11-13/16) Weight Only VS-104.7kg (10lbs. 6oz.) Finish Black, Silver Accessories Remote Control Transmitter x1 RCA Pin Cable (Video x1, Audio x1) Stand x1 Pads (Side x1 and Bottom x1) Batteries x 4 G Speaker Section (NX-VS10M) Type 2 way Bass Reflex (Magnetic-Shielding Type) Speakers 10cm Cone, 2cm Super Tweeter Maximum Power Handling Capacity 25W Impedance 6 Dimensions (W x H x D) 125 x 185 x 145mm (4-15/16 x 7-5/16 x 5-11/16) Weight Only NX-VS10M1.4kg (3lbs. 1oz.) I SW-VS10 (Subwoofer) Minimum RMS Output Power per Channel SW-VS10: 1kHz, 10% THD, 550W NX-VS10C: 1kHz, 10% THD, 640W NX-VS10E: 1kHz, 10% THD, 625W + 25W Type Advanced Active Servo Tecnology type Speakers 16cm Cone (Magnetic-Shielding Type) Maximum Power Handling Capacity 50W Impedance 5 Power Supply U, C modelsAC120V, 60Hz B, G modelsAC230V, 50Hz A modelAC240V, 50Hz Power Consumption U, C models95W B, G, A models90W Standby Power Consumption Reference data0W Dimensions (W x H x D) 200 x 395 x 400mm (7-7/8 x 15-9/16 x 15-3/4) Weight 10.6kg (23lbs. 6oz.) Accessories Wall Bracket x2 Bracket x2 Accessory Cord 4m x1, 15m x 2 DIN Cord x1 Pan Head Screw-sems x2 Wing Bolts x2 Fastener Tape x1set n NX-VS10C (Center Speaker) Type Bass Reflex (Magnetic-Shielding Type) Speakers 8cm Cone x 2 Maximum Power Handling Capacity 40W Impedance 6 Dimensions (W x H x D) 240 x 100 x 145mm (9-7/16 x 3-15/16 x 5-11/16) Weight 1.7kg (3lbs. 12oz.) I NX-VS10E (Rear Speaker) Type Acoustic Suspension (Magnetic-Shielding Type) Speakers 8cm Cone Maximum Power Handling Capacity 30W Impedance 6 Dimensions (W x H x D) 100 x 140 x 112mm (3-15/16 x 5-1/2 x 4-3/8) Weight 0.68kg (1lbs. 8oz.) * Specifications subject to change without notice. U . U.S.A. modelC . Canada model G. Europe modelB . British model A . Australia model * TruBass and the symbol are trademarks of SRS Labs, inc. in the United States and selected foreign countries. TruBass technology is incorporated under license from SRS Labs, inc. *Manufactured under license from Dolby Laboratories. Dolby, Dolby Digital, Pro Logic, and the double-D symbol V are trademarks of Dolby Laboratories. 1992-1997 Dolby Laboratories. All rights reserved. *Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and pending. DTS, DTS Digital Surround, are trademarks of Digital Theater Systems, Inc. copyright 1996 Digital Theater Systems, inc. All rights reserved. VS-10/NX-SW10 Unit : mm (inch) 100 (315/16) 112 (43/8) 140 (51/2) 240 (9-7/16)145 (5-11/16) 100 (3-15/16) Unit : mm (inch) 200 (7-7/8)400 (15-3/4) 395 (15-9/16) Unit : mm (inch) 125 (4-15/16)145 (5-11/16) 185 (7-5/16) Unit : mm (inch) 302 (11-7/8) 300 (11-13/16)88.5 (3-1/2) 82 (3-1/4) Unit : mm (inch) I DIMENSIONS 6 G VS-10G NX-VS10M G SW-VS10 (Subwoofer) G NX-VS10C (Center Speaker)G NX-VS10E (Rear Speaker) VS-10/NX-SW10 3 3 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 1 1 1 2 1 1234 5678 7 (Remove parts in the order as numbered below.) 1. Removal of Side Cover a. Remove 4 screws (1). (Fig. 1) b. Remove the Side Cover. 2. Removal of Bottom Cover a. Remove the screw (2) in Fig. 1, and 2 screws (3) in Fig. 2 to remove the heat sink cover. b. Remove 9 screws (4), and the Bottom Cover can be removed rearward. (Fig. 2) 3. Removal of Top Cover a. Remove 6 screws (5). (Fig. 3) b. Remove the Top Cover. Fig. 1 Fig. 2 I INTERNAL VIEW 1 MAIN P.C.B. (3) 2 MAIN P.C.B. (4) 3 MAIN P.C.B. (1) 4 MAIN P.C.B. (2) 5 DIGITAL P.C.B. (3) 6 MAIN P.C.B. (5) 7 DIGITAL P.C.B. (2) 8 DIGITAL P.C.B. (1) I VS-10 DISASSEMBLY PROCEDURES Fig. 3 VS-10/NX-SW10 Extension flexible flat cable CB1 GND GND CB303 CB311 GND CB302 W306 CB305 GND 9 9 9 9 8 8 8 0 0 0 6 6 6 7 7 7 7 CB1 CB3 CB2 8 Fig. 5 Fig. 6Fig. 7 Fig. 4 I P.C.B. OPERATION CHECK Preparation before operation check a. Remove 3 screws (6). (Fig. 4) b. Remove the DSP Top Cover. c. Disconnect the flexible flat cable (CB1) from DIGITAL P.C.B. (1). (Fig. 4) d. Remove 4 screws (7) and then remove DIGITAL P.C.B. (1) from the DSP Bottom Cover. (Fig. 4) e. Remove 3 screws (8). (Fig. 5) f. Remove the DSP Bottom Cover. g. Remove 4 screws (9). (Fig. 6) h. Remove 3 screws (0). (Fig. 5) i. Remove MAIN P.C.B. (1) from the main chassis. j. Disconnect the flexible flat cable (CB305) from MAIN P.C.B. (1). k. Connect CB305 of MAIN P.C.B. (1) and CB1 of DIGITAL P.C.B. (1) by using an extension cable (5P:MF105250). l. Place MAIN P.C.B. (1) upright with a cloth spread on the main chassis. (Fig. 7) m.Tie one end of a string through the screw hole in the rear panel and the other end through the screw hole in the main chassis to secure them. n. Connect GND (x4 in Fig. 6, 7) to the main chassis by using a lead wire. CAUTION: The grounding point must be connected to main chassis to keep the circuit in normal operation when MAIN P.C.B. (1) and DIGITAL P.C.B. (1) are removed from main chassis. VS-10/NX-SW10 Amplifier Unit A Grill Assembly 9 I SW-VS10 DISASSEMBLY PROCEDURES (Remove parts in the order as numbered below.) 1. Removal of Grille Assembly. a. Insert the tip of flat tip (-) screwdriver to the slot on the bottom. Push up the Grille Assembly by applying force to the screwdriver. (Fig. 8). b. Keep pushing up the Grille Assembly gradually until it can be removed. *The Grille Assembly is fixed securely at 6 dowels. When removing it, use care not to cause a scratch or any damage to the main unit. When reinstalling it, apply quick-drying type bond to the dowels of the Grille Assembly and fit it in place securely. (If it is only pushed in, it will come off easily.) 2. Removal of Amplifier Unit a. Remove 14 screws (A) and then remove the Amplifier Unit. (Fig. 9) Fig. 9 Fig. 8 VS-10/NX-SW10 10 I TEST PROGRAM MODE (VS-10) 1. Procedure for starting Test Program With the power turned off, press the POWER key while pressing the VOLUME key and the DSP key simultaneously. This initiates the Test Program function. When the Test Program is initiated, “01 DEST-Ex” appears on the FL display. 2. Procedure for selecting and executing Test Program Using the VOLUME + (UP) key and Volume - (DOWN) key, select the Test Program and then press the INPUT key to execute it. 3. Procedure for canceling Test Program There are two methods for cancellation. a. Turn off the power by pressing the POWER key of the main unit or the remote controller. b. Select the Test Program “01 DEST-Ex” and press the INPUT key for execution. (The normal mode will be restored.) 4. Details of the Test Program function Display 01 DEST-Ex Function Destination display/ test program end Destination display J:JaJ (Japanese) ExEx models 02 Fact.Test Factory test mode This test mode is used for factory inspection before shipping and is not usually used. If the test program has been executed, it is not possible to shift to another test program. In such case, cancel the test program. 04 FL CHECK FL display light-up check 1st time: FL display segments all light up and standby LED lights up. 2nd time: Even number segments and digits light up and standby LED lights up. 3rd time: Odd number segments and digits light up. 1st time2nd time3rd time 03 FL+CLEAR FL display segments all light up / BACKUP RAM CLEAR 1st time: FL display segments all light up and standby LED lights up. 2nd time: RAM CLEAR is executed (RAM CLEAR OK on display*) * State before shipped out of the factory preset. VS-10/NX-SW10 11 Display 05 DSP Diag Function The DSP DIAG (self-diagnosis) mode is initiated. (Refer to page 7 for the details.) 06 Ver-A1.05 Microprocessor version / date display Example of microprocessor display06 Ver-A1.05 Example of microprocessor date display06 00.08.23 What is displayed varies depending on the microprocessor software. 07 SUMcdbc Check sum calculation display / re-calculation 08 PrCan-OFF All protection cancellation function ON/OFF * 1 09 Pr!CPSProtection operation history display / clear C: VS-10 amplifier voltage (DC) P: Power supply circuit voltage S: SW-VS10 (Subwoofer) side : Normal x: Abnormal 10 RemoCorrRROM collection (EEPROM) remote control data reception / data write This test mode is not usually used. *1CAUTION: Using this product with the protection function cancelled may cause damage to itself. Use special care for this point when using this mode. VS-10/NX-SW10 12 I DSP DIAG MODE (Self-diagnosis) Use the remote controller supplied as an accessory to select the menu. 1. Procedure for starting DSP DIAG Referring to TEST PROGRAM MODE in the previous section, select/execute “05 DSP Diag”. When “05 DSP Diag” is executed, the current input name appears on the display followed by “Sel.1to9 Key”. 2. Procedure for selecting Main menu and Sub-menu Using 1 through 9 keys on the remote controller, select the main menu. Soon the sub-menu will appear on the display. Then, select the sub-menu. Every time the selected key (on the remote controller) is pressed, the sub-menu on the display changes. No.Main menu(Display) 1Analog throughAnalog Thr. 2DSP throughDsp Through 3AC-3/dts throughAC-3/dts Thr. 4Pro logicPro Logic 5Speakers setSpeakers Set 6Effect offEffect Off 7Manual testManual Test 8No function 9DIAG cancel Sub-menu(Display) MAIN BYPASSA.T.M.Bypass DSP 0dBA.T. DSP 0dB YSS908-SRAMDspT.908SRAM YS908DspT.YSS908 DSP FULL BITDspT.FullBit Status (Binary) Analo2/0 CE