Yamaha-RXV-2065-Service-Manual电路原理图.pdf

AV RECEIVER RX-V2065/HTR-6295 1 0 11 4 7 09.08 P.O.Box 1, Hamamatsu, Japan Copyright 2009 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission. SERVICE MANUAL RX-V2065/HTR-6295 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTS TO SERVICE PERSONNEL .23 FRONT PANELS .34 REAR PANELS .57 REMOTE CONTROL PANELS .8 SPECIFICATIONS .915 INTERNAL VIEW .16 SERVICE PRECAUTIONS .16 DISASSEMBLY PROCEDURES .1719 UPDATING FIRMWARE .2029 SELF-DIAGNOSTIC FUNCTION .3066 CONFIRMATION OF IDLING CURRENT OF AMP UNIT .67 DISPLAY DATA .6869 IC DATA .7093 PIN CONNECTION DIAGRAMS .9497 BLOCK DIAGRAMS . 98101 PRINTED CIRCUIT BOARDS .102122 SCHEMATIC DIAGRAMS .123139 REPLACEMENT PARTS LIST .141156 REMOTE CONTROL .157160 ADVANCED SETUP .161162 Note: When IC513 of GUI P.C.B. or GUI P.C.B. is replaced, the network function of this unit will not operate properly without additional setting. In such case, report the serial number of this unit to the following e-mail address. Yamaha Corporation will reply providing the setting procedure to make the network function of this unit operate properly. E-mail: ycav- 2 RX-V2065/HTR-6295 RX-V2065/HTR-6295 This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. 1. Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F. For U model “CAUTION” “F6002: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 125V FUSE.” For C model CAUTION F6002: REPLACE WITH SAME TYPE 10A, 125V FUSE. ATTENTION F6002: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 10A, 125V. All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities. WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! About lead free solder 3 RX-V2065/HTR-6295 RX-V2065/HTR-6295 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. WARNING: Lithium batteries WARNING: Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following precautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disassemble the batteries. Never heat batteries or throw them into fire. ADVARSEL! Lithiumbatteri Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren. VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller an ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty peristo valmistajan ohjeiden mukaisesti. U model C, R, T, K, A, B, G, E, F, L models Top view Front view FRONT PANELS RX-V2065 (U model) 4 RX-V2065/HTR-6295 RX-V2065/HTR-6295 HTR-6295 (C model) RX-V2065 (C, R, K, A, B, G, E, F, L models) RX-V2065 (T model) 5 RX-V2065/HTR-6295 RX-V2065/HTR-6295 RX-V2065 (R model) REAR PANELS RX-V2065 (U model) RX-V2065 (C model) 6 RX-V2065/HTR-6295 RX-V2065/HTR-6295 RX-V2065 (A model) RX-V2065 (T model) RX-V2065 (K model) 7 RX-V2065/HTR-6295 RX-V2065/HTR-6295 HTR-6295 (C model) RX-V2065 (B, G, E, F models) RX-V2065 (L model) 8 RX-V2065/HTR-6295 RX-V2065/HTR-6295 REMOTE CONTROL PANELS RAV296 (U model) RAV297 (C, R, A, L models) RAV298 (T, K, B, G, E, F models) RAV38 (U, C, R, T, K, A, B, G, E, F, L models) 9 RX-V2065/HTR-6295 RX-V2065/HTR-6295 Audio Section Minimum RMS Output Power (Power Amp. Section) (20 Hz to 20 kHz, 0.08 % THD, 8 ohms) FRONT L/R .130 W + 130 W CENTER .130 W SURROUND L/R .130 W + 130 W SURROUND BACK L/R .130 W + 130 W Maximum Power (JEITA) (1 kHz, 10 % THD, 8 ohms) R, T, K, A, L models FRONT L/R .175 W + 175 W CENTER .175 W SURROUND L/R .175 W + 175 W SURROUND BACK L/R .175 W + 175 W MAX. Power Per Channel (1 kHz, 0.7 % THD, 4 ohms) B, G, E, F models FRONT L/R .180 W + 180 W CENTER .180 W SURROUND L/R .180 W + 180 W SURROUND BACK L/R .180 W + 180 W IEC Power (1 kHz, 0.08 % THD, 8 ohms) B, G, E, F models FRONT L/R .130 W + 130 W Dynamic Power Per Channel (IHF) FRONT L/R drive (8 / 6 / 4 / 2 ohms) .160 / 200 / 260 / 330 W Dynamic Headroom U, C models 8 ohms .0.9 dB Damping Factor (20 Hz to 20 kHz, 8 ohms, SPEAKER-A) FRONT L/R .100 or more Input Sensitivity/Input Impedance (1 kHz, 100 W/8 ohms) PHONO (MM) . 3.5 mV / 47 k-ohms AV5 etc. . 200 mV / 47 k-ohms MULTI CH INPUT FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, SUBWOOFER . 200 mV / 47 k-ohms Maximum Input Signal (1 kHz) PHONO (MM) (0.1 % THD) .60 mV or more AV5 etc. (Effect ON) (0.5 % THD) .2.3 V or more Output Level/Output Impedance REC OUT . 200 mV/1.2 k-ohms PRE OUT . 1 V/1.2 k-ohms SUBWOOFER (2 ch stereo and FRONT SP: small) . 1 V/1.2 k-ohms ZONE2, 3 OUT . 200 mV/1.4 k-ohms Headphone Jack Rated Output/Output Impedance AV5 etc. input (1 kHz, 50 mV, 8 ohms) . 100 mV/470 ohms Frequency Response AV5 etc., FRONT (10 Hz to 100 kHz) .+0/-3 dB RIAA Equalization Deviation PHONO (MM) . 0 0.5 dB Total Harmonic Distortion PHONO (MM) to REC OUT (20 Hz to 20 kHz, 1 V) .0.02 % or less AV5 etc. (PURE DIRECT) to FRONT SP OUT (20 Hz to 20 kHz, 50 W) 8 ohms .0.06 % or less SPECIFICATIONS Signal to Noise Ratio (IHF-A network) PHONO (MM) to REC OUT (Input shorted 5 mV) U, C, R, T models . 86 dB or more K, A, B, G, E, F, L models . 81 dB or more AV5, etc. (PURE DIRECT) to SP OUT (Input shorted 250 mV) . 100 dB or more Residual Noise (IHF-A network) FRONT L/R to SP OUT .150 V or less Channel Separation (1 kHz / 10 kHz) PHONO (Input shorted) . 60 dB or more / 55 dB or more AV5, etc. (Input 5.1 k-ohms shorted) . 60 dB or more / 45 dB or more Volume Control .MUTE / -80 dB to +16.5 dB / 0.5 dB step Tone Control Characteristics FRONT L/R Bass Boost/Cut . 10 dB/2 dB, step 50 Hz Turnover frequency .350 Hz Treble Boost/Cut .10 dB/2 dB, step 20 kHz Turnover frequency .3.5 kHz Filter Characteristics FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct. SUBWOOFER small (L.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct. Video Section Video Signal Type (Gray back) Gray back U, C, R, K models .NTSC T, A, B, G, E, F, L models .PAL Video conversion .NTSC/PAL Composite Video Signal Level .1 Vp-p / 75 ohms S-Video Signal Level B, G, E, F models Y .1 Vp-p / 75 ohms C .0.286 Vp-p / 75 ohms Component Video Signal Level Y .1 Vp-p / 75 ohms Cb/Cr .0.7 Vp-p / 75 ohms Video Maximum Input Level VIDEO CONVERSION OFF .1.5 Vp-p or more Video Signal to Noise Ratio . 50 dB or more Monitor Out Frequency Response (VIDEO CONVERSION OFF) Component video signal level .5 Hz to 60 MHz, -3 dB FM Section Tuning Range U, C models .87.5 to 107.9 MHz R, L models .87.5 to 108.0 MHz / 87.50 to 108.00 MHz T, K, A, B, G, E, F models .87.50 to 108.00 MHz 50 dB Quieting Sensitivity (IHF) (1 kHz, 100 % MOD.) Mono .3 V (20.8 dBf) 10 RX-V2065/HTR-6295 RX-V2065/HTR-6295 U .U.S.A. model C .Canadian model R .General model T .Chinese model K .Korean model A .Australian model B .British model G .European model E