Yamaha-RXSL-80-Service-Manual电路原理图.pdf

I CONTENTS TO SERVICE PERSONNEL . 2 IMPEDANCE SELECTOR . 3 FRONT PANELS. 4 REAR PANELS . 56 REMOTE CONTROL PANELS. 6 SPECIFICATIONS / 参考仕様. 710 INTERNAL VIEW . 10 DISASSEMBLY PROCEDURES / 分解手順. 1113 SELF DIAGNOSIS FUNCTION (DIAG) / 自己診断機能（）. 1433 D-AMP MODULE TROUBLESHOOTING / -故障診断. 33 AMP ADJUSTMENT / 部調整.34 DISPLAY DATA . 35 IC DATA . 3642 BLOCK DIAGRAM. 4344 PIN CONNECTION DIAGRAM . 45 PRINTED CIRCUIT BOARD . 4657 SCHEMATIC DIAGRAM . 5864 PARTS LIST . 6579 REMOTE CONTROL. 8081 04.09 100920 P.O.Box 1, Hamamatsu, Japan SERVICE MANUAL AV RECEIVER/AV AMPLIFIER RX-SL80 RX-SL80 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. 2 RX-SL80 RX-SL80 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE I TO SERVICE PERSONNEL 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA- SON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. “CAUTION” “F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125V FUSE.” CAUTION F1: REPLACE WITH SAME TYPE 5A, 125V FUSE. ATTENTION F1: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 5A, 125V. 3 RX-SL80 RX-SL80 本機搭載基板付使用 下記通。 The P.C.B.s installed in this unit are soldered using the following solder. About Lead Free Solder / 無鉛 無鉛種類、修理時下記 無鉛使用推奨。 Sn+Ag+Cu （錫+銀+銅） Sn+Cu （錫+銅） Sn+Zn+Bi （錫+亜鉛+） 注意： 無鉛融点温度通常鉛入比3040 程度高、合 使用。 鉛入使得場合、交換 部品端子部周辺部無鉛取除、 無鉛鉛入十分溶状態 付。 Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: 1. As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. 2. If lead solder must be used, be sure to remove lead free solder from each terminal section of the parts to be replaced and from the area around it completely before soldering, or make sure that the lead free solder and lead solder melt together fully. Side A / A面Side B / B面 DIGITAL P.C.B.Lead Free Solder / 無鉛Lead Free Solder / 無鉛 INPUT P.C.B.Lead Free Solder / 無鉛 MAIN P.C.B.Lead Free Solder / 無鉛Lead Free Solder / 無鉛 POWER P.C.B.Lead Free Solder / 無鉛 I IMPEDANCE SELECTOR (B, G models only) IMPEDANCE SELECTOR WARNING: Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. Side A Side B SMT REFLOW Process MI FLOW Process Solder Dip 4 RX-SL80 RX-SL80 I FRONT PANELS RX-SL80 (U, C, R, T, K, A, L models) RX-SL80 (B, G models) RX-SL80 (J model) 5 RX-SL80 RX-SL80 RX-SL80 (T model) RX-SL80 (K model) RX-SL80 (A model) RX-SL80(B, G models) I REAR PANELS RX-SL80 (U, C models) RX-SL80 (R model) 6 RX-SL80 RX-SL80 I REMOTE CONTROL PANELS U, C, R, T, K, A, L, J modelsB, G models RX-SL80 (L model) RX-SL80 (J model) 7 RX-SL80 RX-SL80 I Audio Section / 部 Minimum RMS Output Power (Power Amp. Section) / 定格出力 (部) (1 kHz) FRONT L/R U, C models (0.9% THD, 6 ohms) .(FTC) 65W + 65W R, T, K, A, B, G, L, J models (0.9% THD, 6 ohms) . 70W + 70W CENTER U, C models (0.9% THD, 6 ohms) . (FTC) 65W R, T, K, A, B, G, L, J models (0.9% THD, 6 ohms) . 70W SURROUND L/R U, C models (0.9% THD, 6 ohms) .(FTC) 65W + 65W R, T, K, A, B, G, L, J models (0.9% THD, 6 ohms) . 70W + 70W Maximum Power / 実用最大出力 (EIAJ, 1kHz, 10% THD) FRONT L or R R, T, K, A, B, G, L, J models (6 ohms). 100W CENTER R, T, K, A, B, G, L, J models (6 ohms). 100W SURROUND L or R R, T, K, A, B, G, L, J models (6 ohms). 100W Input Sensitivity / Input Impedance (入力感度/入力 ) (U, C, R, T, K, A, L, J models) DVD/CD, etc.200 mV / 47 k-ohms (B, G models) VIDEO 2, EXT. IN, TV IN .200 mV / 47 k-ohms Maximum Input Signal Level / 最大許容入力 (1 kHz, 0.5% THD) (U, C, R, T, K, A, L, J models) DVD/CD, etc. 2.0 V or more (B, G models) VIDEO 2, EXT. IN, TV IN . 2.0 V or more Output Level / Output Impedance (出力電圧/出力 ) VCR OUT (U, C, R, T, K, A, L, J models) . 200 mV / 820 ohms EXT., TV (B, G models) .200 mV / 1.0 k-ohms SUB WOOFER (FRONT SP: Small) .2.0 V / 1.2 k-ohms Headphone Jack Rated Output / Impedance ( 出力/出力) DVD/CD, etc. (1 kHz, 47 mV, 8 ohms) . 100 mV / 100 ohms Frequency Response / 周波数特性 DVD/CD, etc. to FRONT L/R (20 Hz to 50 kHz) .+0/-3.0 dB Total Harmonic Distortion / 全高調波歪率 (1 kHz, 35W, 6 ohms) (U, C, R, T, K, A, L, J models) DVD/CD, etc. (Effect Off) to FRONT L/R . 0.04 % or less (B, G models) EXT. IN (Effect Off) to FRONT L/R . 0.04 % or less Signal to Noise Ratio / 信号対雑音比 (IHF-A network) (U, C, R, T, K, A, L, J models) DVD/CD, etc. (Input shorted, 250 mV, Effect Off) to SP OUT . 100 dB or more (B, G models) EXT. IN (Input shorted, 250 mV, Effect Off) to SP OUT . 100 dB or more Residual Noise / 残留 (IHF-A network) FRONT L/R . 150 V or less Channel Separation / (Vol -14 dB, Effect Off) DVD/CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) . 60 dB or more/45 dB or more Tone Control Characteristics / 特性 BASS Boost/Cut .10 dB (60Hz) TREBLE Boost/Cut . 10 dB (20kHz) Filter Characteristics / 特性 FRONT, CENTER, SURROUND : SMALL (H.P.F.) .40/ 60/ 80/ 90/ 100/ 110/ 120/ 160/ 200 Hz, 12 dB / oct. SUBWOOFER (L.P.F.) .40/ 60/ 80/ 90/ 100/ 110/ 120/ 160/ 200 Hz, 24 dB / oct. I Video Section / 部 Video Signal Type / 信号方式 U, C, R, K, J models .NTSC T, A, B, G, L models.PAL Video Signal Level / 信号 .1 Vp-p / 75 ohms Maximum Input Level / 最大許容入力 . 1.5 Vp-p or more Signal to Noise Ratio / 信号対雑音比 . 50 dB or more Monitor Out Frequency Response / 周波 数帯域 Video Signal Level .5 Hz to 10 MHz, -3 dB I FM Section / FM部 Tuning Range U, C models .87.5 to 107.9 MHz T, K, A, B, G models .87.50 to 108.00 MHz R, L models . 87.5 to 108.0 / 87.50 to 108.00 MHz J model.76.0 to 90.0 MHz 50dB Quieting Sensitivity / 50dB SN感度 (IHF) (1kHz, 100% Mod.) Mono .2.8 V (20.2 dBf) Signal to Noise Ratio / 信号対雑音比 (IHF) Mono / Stereo. 73 dB / 70 dB Harmonic Distortion / 歪率 (1 kHz) Mono / Stereo.0.5 % / 0.5 % Antenna Input / 入力 .75 ohms unbalanced I AM Section / AM部 Tuning Range / 受信周波数範囲 U, C models . 530 to 1,710 kHz T, K, A, B, G, J models . 531 to 1,611 kHz R, L models . 530 to 1,710 / 531 to 1,611 kHz Antenna / 入力 .Loop Antenna I SPECIFICATIONS / 参考仕様 8 RX-SL80 RX-SL80 55.5 (2-3/16) 300 (11-13/16) 9.6 (3/8) 15.6 (5/8) 325.2 (12-13/16) 435 (17-1/8) Unit : mm (inch) 単位: mm（） I General / 総合 Power Supply / 電源電圧 U, C models . AC 120 V, 60 Hz R model . AC 110 120 V, 50/60 Hz T model . AC 220 V, 50 Hz K model . AC 220 V, 60 Hz A model . AC 240 V, 50 Hz B, G models . AC 230 V, 50 Hz L model. AC 220 240 V, 50/60 Hz J model. AC 100V, 50/60 Hz Power Consumption / 消費電力 U, C models . 90 W R, T, K, A, B, G, L models . 90 W J model. 130 W Standby Power Consumption (reference data) / 待機時 消費電力(参考値) U, C, R, J models . 0.8 W T, K, A, L models. 0.9 W B, G models (Scart Off/On). 0.9 W / 2.5 W Dimensions / 寸法 (W x H x D) .435 x 55.5 x 325 mm (17-1/8 x 2-3/16 x 12-13/16) Weight / 質量 . 6.4 kg (14 lbs. 2 oz.) Finish / 仕上 . Silver color Accessories / 付属品 Remote Control x 1, Battery (Manganese Dry) x 2, Indoor FM Antenna x 1, AM Loop Antenna x 1, Cable Tag x 5 pairs * Specifications are subject to change without notice due to product improvements. 参考仕様外観予告変更。 U . U.S.A. modelA. Australian model C . Canadian modelB. British model R . General modelG . European model T . Chinese modelL . Singapore model K . Korean modelJ . Japanese model Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. 実施権基製造。 、DOLBY、PRO LOGICD記号 、商標。 SILENT CINEMA is a trademark of YAMAHA CORPORATION. SILENT CINEMA 株式会社登録商標 。 “DTS” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. DTS、DTS 96/24登録商標。 AAC商標。 DIMENSIONS / 寸法図 9 RX-SL80 RX-SL80 Set Menu Table / ROOM: SUBWOOFER SPEAKERS SET Check: Check OK? CENTER FRONT SUR. LR BASS OUT CROSS OVER SUBWOOFER PHASE FR C SL SR SWFR UNI T FRONT L FRONT R CENTER SUR L SUR R SWFR TEST 100 Hz 300 Hz 1 kHz 3 kHz 10 kHz SP LFE HP LFE SP D. R HP D. R A. MUTE A. DELAY DUAL MONO I N (1) I N (2) I N (3) SET DI MMER MENU SHI FT MEM. GUARD STEP STANDBY Category BASI C SET UP MANUAL SET UP No. 1 2 3 MAIN MENU SOUND I NPUT OPTI ON A B C D E F G A B A B C D D SUB MENU SPEAKER SET SP LEVEL SP DI STANCE CENTER GEQ LFE LEVEL D. RANGE AUDI O SET I NPUT ASSI GN I NPUT MODE DI SPLAY SET MEMORY GUARD PARAM. I NI TUNER SET SCART SET SELECT MENU SM L YES 5 spk CANCEL Test Tone YES SML LARGE SML BOTH 80 Hz NORMAL L - - R L - - R L - - R L - - R SWFR - met ers (R, T, K, A, B, G, L, J models) feet (U, C models) 3. 0 m 10. 0 ft 3. 0 m 10. 0 ft 3. 0 m 10. 0 ft 3. 0 m 10. 0 ft 3. 0 m 10. 0 ft 3. 0 m 10. 0 ft OFF - - 0 - - 0 - - 0 - - 0 - - 0 0 dB 0 dB MAX MAX MUTE 0 ms MAI N DVD/ CD DTV/ CBL VI DEO1 AUTO 0 0 OFF AM9/ FM50 ON S, M, L YES, NONE 2, 3, 4, 5 SET, CANCEL YES, No LRG, SML, NON LARGE, SMELL LRG, SML, NON BOTH, FRNT, SWFR 40, 60, 80, 90, 100, 110, 120, 160, 200 NORMAL, REVERSE Cent er 10 st ep Cent er 10 st ep Cent er 10 st ep Cent er 10 st ep -20 t o 0 dB, 1dB st ep met ers (m) feet (ft ) 0. 3 t o 24 m, 3. 0 m, 0. 1m st ep 1. 0 t o 80. 0 feet , 10. 0 feet , 0. 5 feet st ep 0. 3 t o 24 m, 3. 0 m, 0. 1m st ep 1. 0 t o 80. 0 feet , 10. 0 feet , 0. 5 feet st e