Yamaha-HTR-6040-Service-Manual电路原理图.pdf

SERVICE MANUAL 101041 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. I CONTENTS TO SERVICE PERSONNEL . 2 FRONT PANELS. 34 REAR PANELS . 47 REMOTE CONTROL PANELS. 8 SPECIFICATIONS / 参考仕様 . 911 INTERNAL VIEW . 12 DISASSEMBLY PROCEDURES / 分解手順. 1214 UPDATING FIRMWARE / 書込. 1517 SELF DIAGNOSIS FUNCTION (DIAG) / 自己診断機能（）. 1836 DISPLAY DATA . 37 IC DATA . 3852 BLOCK DIAGRAMS . 5354 PIN CONNECTION DIAGRAMS. 55 PRINTED CIRCUIT BOARDS. 5668 SCHEMATIC DIAGRAMS. 6980 REPLACEMENT PARTS LIST . 8195 REMOTE CONTROL. 9699 Advanced setup / 設定初期設定戻. 100 P.O.Box 1, Hamamatsu, Japan 2007 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission. 07.02 RX-V461/HTR-6040/ DSP-AX461 This service manual is the RX-V461/HTR-6040/DSP-AX461 (U, C, R, K, A, L and J models). For service manual of the RX-V461/RX-V461DAB (T, B, G and E models), please refer to the following publi- cation number: RX-V461/RX-V461DAB (T, B, G and E models): 101048 For U, C, R, K, A, L and J models AV RECEIVER/AV AMPLIFIER RX-V461/HTR-6040/DSP-AX461 RadioFans.CN 收音机爱 好者资料库 RX-V461/HTR-6040/DSP-AX461 15 RX-V461/HTR-6040/ DSP-AX461 Optical cable 光 DVD/CD player DVD/CD Main unit 本機 DVD/CD player DVD/CD Main unit 本機 Digital audio pin cable I UPDATING FIRMWARE / 書込 下記部品部品交換場合、最新 書込行。 DSP P.C.B. IC201 （DSP P.C.B.） 必要 DVDCD （DIGITAL OUTPUT （OPTICALCOAXIAL） 端子付） 光 （OPTICAL端子使用時） 音声 （COAXIAL端子使用時） CD CD、PC最新 指定先 制作。 操作方法 1. 本機DVD/CD下記接続 。 （Fig. 1） Fig. 1 Example of OPTICAL terminal / OPTICAL端子使用例 Example of COAXIAL terminal / COAXIAL端子使用例 After replacing the following parts with the replacement part, be sure to write the latest firmware. DSP P.C.B. IC201 (DSP P.C.B.) G Required Tools DVD or CD player (with DIGITAL OUTPUT (OPTICAL or COAXIAL) terminal) Optical cable (when OPTICAL terminal is used) Digital audio pin cable (when COAXIAL terminal is used) Firmware CD *To make the firmware CD, download the latest firm- ware from the specified download source to PC. G Operation Procedures 1. Connect the main unit and DVD/CD player as shown below. (Fig. 1) RadioFans.CN 收音机爱 好者资料库 RX-V461/HTR-6040/DSP-AX461 16 RX-V461/HTR-6040/ DSP-AX461 Fig. 2 2. 本機 “STANDBY/ON” 、 “SPEAKERS A/B/ OFF” 押、本機電源AC 接続。 （Fig. 2） FIRMWARE UPDATE起動、 “SPDIF Upgrade” 表示。 （Fig. 2） Writing is completed. / 書込完了Writing is started. / 書込開始 Fig. 3 3. DVD/CD電源AC 接続。 4. DVD/CD “STANDBY/ON” 押 。 5. DVD/CD “EJECT” 押、 開。 6. CD載、閉 。 7. DVD/CD “PLAY” 押。 書込開始。 （Fig. 3） 8. 書込完了後、 “Upgrade OK” 、 “Please.” 、 “Turn off!” 繰返表示 。 （Fig. 3） 2. While pressing the “STANDBY/ON” key and “SPEAK- ERS A/B/OFF” key of the main unit simultaneously, connect the power cable of the main unit to the AC outlet. (Fig. 2) The FIRMWARE UPDATE mode will then be acti- vated and “SPDIF Upgrade” is displayed. (Fig. 2) 3. Connect the power cable of DVD/CD player to the AC outlet. 4. Press the “STANDBY/ON” key of the DVD/CD player. 5. Press the “EJECT” key of the DVD/CD player to open the tray. 6. Put the firmware CD on the tray and close the tray. 7. Press the “PLAY” key of the DVD/CD player. Then writing of the firmware is started. (Fig. 3) 8. When writing of the firmware is completed, “Up- grade OK”, “Please.” and “Turn off!” are dis- played repeatedly. (Fig. 3) FIRMWARE UPDATE mode STANDBY/ON keySPEAKERS A/B/OFF key SPDIF Upgrade Address:XXXXXXUpgrade OK Please. Turn off! XXXXXX: Address information of the received data / 受信情報 RX-V461/HTR-6040/DSP-AX461 17 RX-V461/HTR-6040/ DSP-AX461 本機既存、書込 同場 合、 “Same Version” 、 “Please.” 、 “Turn off!” 表示繰返。 （ 必要。） CD再生開始後、10秒以上経 過表示変場合、 CD再生最初直 。 “Address:XXXXXX” 後、 “FILE CORRUPTED” 表示場合、書込破損 確認、 “操作方法” 18 一度直。 “Upgrade Failed” 表示場合、 “操作方 法” 18一度直 。 9. DVD/CD “STOP” 押。 10.DVD/CD “EJECT” 押、 開。 11.CD外、閉 。 12.DVD/CD電源切、電源 AC抜。 13.本機 “STANDBY/ON” 押電源切 。 確認 正更新確認 。 詳細 自己診断 （） 参 照。 表示 、書込 異場合、 “操作方 法” 113一度直 。 *When the version of the firmware to be written is the same as the one existing in the main unit, “Same Version”, “Please.” and “Turn off!” are displayed repeatedly. (Upgrading is not neces- sary.) If the display remains unchanged for more than 10 seconds after starting the firmware CD play procedure, perform the firmware CD play pro- cedure again from the beginning. If “FILE CORRUPTED” is displayed after “Address:XXXXXX”, check to make sure that the written data is not corrupted and perform Steps 1 to 8 of “Operation Procedures” again. If “Upgrade Failed” is displayed, perform Steps 1 to 8 of “Operation Procedures” again. 9. Press the “STOP” key of the DVD/CD player. 10.Press the “EJECT” key of the DVD/CD player to open the tray. 11.Remove the firmware CD from the tray and close the tray. 12.Turn off the power of the DVD/CD player and dis- connect the power cable from the AC outlet. 13.Turn off the power by pressing the “STANDBY/ON” key of the main unit. G Confirmation of firmware version and checksum Confirm that the firmware version and checksum value is updated successfully with the DIAG function. For more information, refer to “SELF DIAGNOSIS FUNC- TION (DIAG)”. *When the displayed firmware version and checksum are different from written firmware version and checksum, follow the steps from 1 to 13 of “Opera- tion Procedures” again. RX-V461/HTR-6040/DSP-AX461 18 RX-V461/HTR-6040/ DSP-AX461 I SELF DIAGNOSIS FUNCTION (DIAG)自己診断機能 （） This unit has self diagnosis functions that are intended for inspection, measurement and location of faulty point. There are 18 DIAG menu items, each of which has sub- menu items. Listed in the table below are menu items and sub-menu items. Note that not all menu items listed will apply to the models covered in this service manual. 本機、検査、測定、不良個所発見目的自己 診断機能 （） 。 18個、 。 下表一覧。 下表全項目、 記載適用限。 No.DIAG menuSub-menu 1 2 3 4 5 6 7 8 9 10 11 12 13 BYPASS AUDIO CHECK SPEAKERS SET 6CH-INPUT MIC CHECK FL/OSD CHECK TEST TONE FACTORY PRESET AD DATA CHECK XM STATUS (U, C models) DOCK USB (Not applied to these models.) DAB (Not applied to these models.) ANALOG BYPASS DSP BYPASS AUDIO CHECK FRNT : SML 0dB CENTER : NONE LFE/B : FRNT TONE : MAX TONE : MIN 6ch INPUT 6-ohm 6ch INPUT 8-ohm LIM : , PLDET : , THM : MIC CHECK VFD CHECK VFD DISP OFF VFD DISP ALL VFD DIMMER CHECK PATTERN TEST ALL TEST FRNT L TEST CENTER TEST FRNT R TEST SURR R TEST SURR L TEST LFE PRESET INHI PRESET RSRV PD : , PV : TH : , PL : PI : , DE : K0 : , K1 : 1k -1dB/44 1k -61dB/44 Mute/44 XM Tone/44 ISO Tone/44 1k -1dB/32 1k -61dB/32 Mute/32 XM Tone/32 ISO Tone/32 Bus Power : OFF DOCK : DOCK ignore USB 1 USB 2 DAB 1 DAB 2 DAB 3 RX-V461/HTR-6040/DSP-AX461 19 RX-V461/HTR-6040/ DSP-AX461 No.DIAG menuSub-menu 14 15 16 17 18 IF STATUS (Not applied to these models.) PROTECTION PROTECTION HISTORY SOFT SWITCH ROM VER/SUM IF 1 IF 2 IF 3 IF 4 IF 5 IF 6 IF 7 IF 8 IF 9 IF 10 IF 11 IF 12 IF 13 IF 14 IF 15 IF 16 IF 17 PRD L : PRD H : PRV L : PRV H : THM : PLD8H : PLD8L : PLD6H : PLD6L : PRI : PDET : History 1 History 2 History 3 History 4 SW MODE MODEL DESTINATION TUNER DESTINATION VIDEO FORMAT AAC OSD YPAO RDS XM DAB USB DOCK (iPod) VERSION ALL CHECKSUM PROGRAM CHECKSUM SPI CHECKSUM SPD CHECKSUM XM VERSION DAB VERSION FlashROM TEST SDRAM TEST EEPROM TEST RX-V461/HTR-6040/DSP-AX461 20 RX-V461/HTR-6040/ DSP-AX461 起動 本体下図示同時押 “STANDBY/ ON” 押、起動。 Starting DIAG Press the “STANDBY/ON” key while simultaneously pressing those two keys of the main unit as indicated in the figure below. Turn on the power while pressing these keys. / 同時押、電源。 Keys of main unit / 本機 解除 1. 解除前、No. 8 FACTORY PRESET （初期化禁止 初期化） 設定。 保持場合、必 PRESET INHIBITED （初期化禁止） 選 択。 2. 本機 “STANDBY/ON” 押、電源 。 起動時表示 本機FL、 （ 履歴） 表示、数秒後 表示 （1. ANALOG BYPASS） 。 Canceling DIAG 1. Before canceling DIAG, execute setting for FAC- TORY PRESET of DIAG menu No.8 (Memory ini- tialization inhibited or Memory initialized). *In order to keep the user memory stored, be sure to select PRESET INHIBITED (Memory ini- tialization inhibited). 2. Turn off the power by pressing the “STANDBY/ON” key of the main unit. Display provided when DIAG started On the FL display of the main unit, an opening mes- sage (including the protection history) appears for a few seconds followed by the DIAG menu display (1. ANALOG BYPASS). 解除起動 動作、故障箇所診 断支障場合、次方法 解除状態入 。 （過電流検出以外動 作解除） 上図同時押 “STANDBY/ON” 押。、上図3秒以上押続 。 本体FL SLEEP 点滅 、解除状態 知。 Starting DIAG in the protection cancel mode If the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described below, and it will be possible to enter the DIAG mode. (The protection functions other than the excess current detect function will be disabled.) Press the “STANDBY/ON” key while simultaneously pressing those two keys indicated in the figure above. At this time, keep pressing those two keys for 3 sec- onds or longer. In this mode, the SLEEP segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the protection functions disabled. 注意！ 解除起動、危険状態 作動、動作本機 破壊。 使用場合十分注意。 CAUTION! Using this product with the protection function dis- abled may cause damage to the main unit. Use spe- cial care for this point when using this mode. RX-V461/HTR-6040/DSP-AX461 21 RX-V461/HTR-6040/ DSP-AX461 NO PROTECTION After a few seconds / 数秒後 DIAG menu display / 表示 1.ANLOG BYPASS Opening message / 表示 When there is no protection history 履歴無場合 履歴場合： 過電流履歴場合 When there is a history of protection function: When there is a history of protection function due to excess current PRI PRT:xxx 原因：過電流流。 補足：電流検出、 電流検出異常 特定。 異常状態電源、瞬時 、電源切 。 Cause: An excessive current flowed through the power amplifier. Supplementary information: As current of the power amplifier is detected, the abnormal channel can be identified by checking the current detect transistor. Turning on the power without correcting the abnormality will cause the protection func- tion to work immediately and the power sup- ply will instantly be shut off. When there is no history of protection function:履歴無場合： AD value when the protection function is working 動作時A/D値 AD value when the protection function is working 動作時A/D値 DC出力異常履歴場合When there is a history of protection function due to abnormal DC output 原因：DC出力異常。 補足：故障端子直流電圧 掛原因、働 示。 異常状態、約3秒後 掛、電源切 。 Cause: DC output of the power amplifier is abnormal. Supplementary information: The protection function worked due to a DC voltage appearing at the speaker terminal. A cause could be a defect in the amplifier. If the power is turned on with the abnormality unsolved, the protection function works in about 3 seconds to turn off the power. PRD PRT:xxx 注意！ 異常状態本機電源入、危険状態 、回路損傷受原因。 連続 “PRI” “PRD” 働場合、3回目 “STANDBY/ON” 押 電源入。再度電源入場合、 一度本機電源AC電源抜 接続直。 本機電源前、各内 出力損傷 。 電流、各抵抗器 間測定。 Note) Applying the power to the main unit without cor- recting the abnormality can be dangerous and cause additional circuit damage. To avoid this, if “PRI” and “PRD” protection function has been ac- tivated 3 times continuously, the power will not turn on even when the “STANDBY/ON key is pressed. In order to turn on the power again, dis- connect the power cable of the main unit from the AC outlet once and then reconnect it again. The output transistors in each amplifier channel should be checked for damage before applying power of the main unit. Amplifier current should be monitored by measur- ing across the emitter resistors for each channel. RX-V461/HTR-6040/DSP-AX461 22 RX-V461/HTR-6040/ DSP-AX461 原因：温度異常。 補足：温度制限越原因、 働示。 異常状態、約1秒後 掛、電源切。 各検出関、後述 参照。 異常温度履歴 場合 When there is a history of protection function due to excessive heat sink temperature Cause: The temperature of the heat sink is excessive. Supplementary information: The protection function worked due to the temperature limit being exceeded. Causes could be poor ventilation or a defect related to the thermal sensor. If the power is turned on with the abnormality unsolved, the protection function works in about 1 second to turn off the power. For detection of each protection function, refer to DIAG menu described later. THM PRT:xxx 電源部電圧異常履歴場合When there is a history of protection function due to abnormal voltage in the power supply section PRV PRT:xxx 原因：電源部電圧異常。 補足：電源電圧原因、働 示。 異常状態、約1秒後 掛、電源切 。 Cause: The voltage in the power supply section is abnormal. Supplementary information: The protection function worked due to a de- fect or overload in the power supply. If the power is turned on with the abnormality unsolved, the protection function works in about 1 second to turn off the power. AD value when the protection function is working 動作時A/D値 AD value when the protection function is working 動作時A/D値 履歴 働場合、履