Yamaha-RXE-100-Service-Manual电路原理图.pdf

RX-E100 RX-E100 SERVICE MANUAL I CONTENTS TO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . . . .1 FRONT PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 DISASSEMBLY PROCEDURES . . . . . . . . . . . . . . . . .5 TEST MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 AMP ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . .7 TUNER ADJUSTMENTS . . . . . . . . . . . . . . . . . . . 810 IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1113 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . 1415 PRINTED CIRCUIT BOARD . . . . . . . . . . . . . . . 1624 PIN CONNECTION DIAGRAM . . . . . . . . . . . . . . . . .25 SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . 2628 REMOTE CONTROL TRANSMITTER . . . . . . . . . . . .29 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3038 SYSTEM CONTROL . . . . . . . . . . . . . . . . . . . . . 3948 NX-E100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. IMPORTANT NOTICE 100684 SERVICE MANUAL RX-E100/NX-E100 MINI COMPONENT SYSTEM CRX-E100 CRX-E100 is composed of RX-E100 and CDX-E100. This is a service manual for the RX-E100 (including NX-E100). For service manuals of CDX-E100, please refer to the service manuals with the following publication numbers : CDX-E100100685 RX-E100 RX-E100 I TO SERVICE PERSONNEL 1. Critical Components Information. Components having special characteristics are marked Z and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only). When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. AC LEAKAGE TESTER OR EQUIVALENT EQUIPMENT UNDER TEST INSULATING TABLE WALL OUTLET WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. 1 M U, C, R, A models M B, G models I FRONT PANELS GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. RX-E100 RX-E100 2 I REAR PANELS M U model M C model M R model M A model M B model M G model RX-E100 RX-E100 I FM SECTION Tuning Range U, C models . . . . . . . . . . . . . . . . . . . . . . . 87.5 to 107.9MHz A, B, G models . . . . . . . . . . . . . . . . . . . 87.50 to 108.00MHz R model . . . . . . . . . . . . . . 87.5 to 108.0/87.50 to 108.00MHz Usable Sensitivity (75 ) Mono (S/N 30dB) U, C, R models . . . . . . . . . . . . . . . . 1.5V DIN, Mono (S/N 26dB) A, B, G models . . . . . . . . . . . . 1.8V Alternate Channel Selectivity U, C, R models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75dB Selectivity (two signals, 40kHz Dev.) A, B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55dB Signal-to-Noise Ratio Mono/Stereo (IHF) U, C, R models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77/71dB Mono/Stereo (DIN-weighted, 40kHz Dev.) A, B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71/65dB Harmonic Distortion Mono/Stereo (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . 0.5/1.0% Frequency Response 20Hz to 15kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 1.5dB Stereo Separation 1kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB I AUDIO SECTION Minimum RMS Output Power per Channel 20Hz to 20kHz, 0.1% THD, 6 U, C, A, B, G models . . . . . . . . . . . . . . . . . . . . 40W + 40W 1kHz, 0.07% THD, 6 . . . . . . . . . . . . . . . . . . . . 50W + 50W Maximum Power per Channel (EIAJ) 1kHz, 10% THD, 6 (R model only) . . . . . . . . . 60W + 60W Dynamic Power per Channel (IHF) 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50W + 50W 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65W + 65W 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75W + 75W 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80W + 80W DIN Standard Output Power per Channel 1kHz, 0.7% THD, 4 (G model only) . . . . . . . . . 60W + 60W Dynamic Headroom (6) U, C, models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0dB IEC Power 1kHz, 0.04% THD, 6 (G model only) . . . . . . . . 50W + 50W Power Band Width 0.1% THD, 30W/6 . . . . . . . . . . . . . . . . . . . 10Hz to 50kHz Damping Factor 20Hz to 20kHz, 6 . . . . . . . . . . . . . . . . . . . . . . . .60 or more Input Sensitivity/Impedance CD, etc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150mV/47k Maximum Input Signal Level (1kHz, 0.5% THD) CD, etc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0V Output Level/Impedance REC OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150mV/1.2k SUB WOOFER (50Hz) . . . . . . . . . . . . . . . . . . . . . . 2V/730 Headphone Jack Rated Output/Impedance CD, etc 1kHz, 150mV, 6 . . . . . . . . . . . . . . . . . 0.43V/330 Frequency Response (20Hz to 20kHz) CD, etc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00.5dB Total Harmonic Distortion (20Hz to 20kHz) CD, etc to MAIN SP OUT (20W/6) . . . . . . . . . . . . . 0.04% Signal-to-Noise Ratio (IHF-A-Network) CD, etc, Input Shorted (150mV) . . . . . . . . . . . . . . . . . . 93dB Residual Noise (IHF-A-Network) SP OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100V Channel Separation (Vol. 30dB) CD, etc, Input 5.1k Shorted, 1kHz/10kHz . . . . .60dB/45dB Tone Control Characteristics BASS: Boost/cut . . . . . . . . . . . . . . . . . . . . 10dB (50Hz) Turnover Frequency . . . . . . . . . . . . . . . . . 350Hz TREBLE : Boost/cut . . . . . . . . . . . . . . . . . . . 10dB (20kHz) Turnover Frequency . . . . . . . . . . . . . . . . . 3.5kHz Filter Characteristics SUB WOOFER (L.P.F.) . . . . . . . . . . . . . fc = 100Hz, 6dB/oct. I SPECIFICATIONS 3 I AM SECTION Tuning Range U, C models . . . . . . . . . . . . . . . . . . . . . . . .530 to 1710kHz A, B, G models . . . . . . . . . . . . . . . . . . . . . .531 to 1611kHz R model . . . . . . . . . . . . . . . . 530 to 1710/531 to 1611kHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V/m Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB I TUNER SECTION Tuner Output Level FM (1kHz) 100% mod. U, C, R models . . . . . . . . . . . . . . . . . . . 500mV 40kHz Dev. A, B, G models . . . . . . . . . . . . . . . . . . . 270mV AM (30% mod., 1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . 150mV I GENERAL Power Supply U, C models . . . . . . . . . . . . . . . . . . . . . . . . AC 120V, 60Hz A model . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240V, 50Hz B, G models . . . . . . . . . . . . . . . . . . . . . . . . AC 230V, 50Hz R model . . . . . . . . . . . . . . AC 110/120/220/240V, 50/60Hz Power Consumption U, C models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110W R, A, B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . 100W AC Outlets Switched x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100W max Dimensions (W x H x D) . . . . . . . . . . . . . . 217 x 108 x 312mm (8-9/16 x 4-1/4 x 12-5/16) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 kg (9 lbs. 14 oz) Accessories . . . . . . . . . . . . . . . . . . . . . . AM loop antenna x 1 Indoor FM antenna x 1 Remote Control Transmitter x 1 Battery (size UM-4E, R03) x 4 * Specifications subject to change without notice. U . USA model C . Canadian model A . Australian model B . British model G . European model R . General model RX-E100 RX-E100 4 I INTERNAL VIEW qP. C. B. MAIN (6) wP. C. B. MAIN (1) eP. C. B. TUNER rP. C. B. MAIN (2) tP. C. B. OPERATION yPOWER TRANSFORMER uP. C. B. MAIN (4) iP. C. B. MAIN (3) qrwe iytu G DIMENSIONS Units : mm (inch) 275(10-13/16)22 (7/8) 15 (9/16) 8 (5/16) 312(12-5/16) 217(8-9/16) 100(3-15/16) 108(4-1/4) RX-E100 RX-E100 Fig. 1 q q Top Cover Fan w w e r t Fig. 2 Amp Unit y Fig. 3 I DISASSEMBLY PROCEDURES (Remove parts in disassembly order as numbered.) 1. Removal of Top Cover a. Remove 4 screws ( q ) and 4 screws ( w ) in Fig. 1. 5 y 2. Checking the Amp Unit and replacing parts a. Disconnect the power plug from AC outlet. b. Remove 2 screws ( e ) attaching the rear panel to the chassis. (Fig. 2) c. Disconnect the connector for the fan. d. Remove 3 screws ( r, t ) attaching the fan to the chassis and then remove the fan. (Fig. 2) e. Remove 3 screws ( y ) attaching the Main P.C.B. to the Heat Sink. (Fig. 2) f. Loosen the wiring harness. g. Move the Amp Unit toward the rear. (Fig. 2) h. As shown in Fig. 3, set the Amp Unit upright. i. Fit insulating material (thick paper, etc.)to prevent the chassis and the transformer from contacting the Main P.C.B. j. Using a wire, connect the pin jack ground to the chassis. (If they are left unconnected, the grounding remains open and the unit fails.) k. Connect the power plug and turn on the power switch. l. When replacing parts, remove 5 screws ( u, i ) fixing the P.C.B. Tuner and then remove the P.C.B. Tuner. (Fig. 3) u i (Copper) (Copper) (Copper) RX-E100 RX-E100 6 ITEST MODE STANDBY/ON Key is pushed while pushing DISPLAY Key and AUTO/MANL Key. TEST MODE indication. PRESET/TUNING B Key Test mode number up. PRESET/TUNING N Key Test mode number down. PRESET/BAND Key Executive test mode. STANDBY/ON Key POWER OFF The completion of test mode. POWER Off condition TEST MODE UPTEST MODE DOWN When present mode is carried out. Test mode is finished. DISPLAYFUNCTIONPRESET/BAND Key 01 DEST-B,G 02 FL+CLEAR Stop/Low/High DESTINATIONR (AM9k/FM:50k)R (AM10k/FM100k)AB,GU,CJ DisplayR9kR10kAB, GU, CJ (*1) 03 FL CHECK 04 FANStop 05 Ver-Z1.02 06 SUM5b4d 0599.05.28 TEST PROGRAM MODE FUNCTION DESCRIPTION Indication for destinaion. (*1) All FL segments and BACKUP RAM CLEAR. All FL segments and circuit board short circuit inspection. Cooling fan drive OUT Version information of the microcomputer software. (*2) The date of the microcomputer software. (*2) The calculation of SUM is done and indicated after that. (*2) 1st : all segments light 2nd : RAM CLEAR 1st : all segments light 2nd : Even-numbered segments and even numbered digits are turned on. 3rd : Odd -numbered segments and odd- numbered digits are turned on. It is changed to the date indication. It is changed to version indication. Re-calculation (*2) Contents of indication change by the microcomputer software. (Note that memories set by the user will be erased.) Also, the preset contents of the tuner are restored to the factory preset ones. PRESET EDIT VOLUMERDS PSPTY RT CT PTY HOLD STEREOAUTOTIMER SLEEPTUNEDMEMORY TIMER STANDBY EDIT VOLUMERDSPTYCTSTEREOAUTOTIMERPRESETPSRT PTY HOLDSLEEPTUNEDMEMORY TIMER STANDBY PRESET EDIT VOLUMERDS PSPTY RT CT PTY HOLD STEREOAUTOTIMER SLEEPTUNEDMEMORY TIMER STANDBY FL CHECK 1st 2nd 3rd RX-E100 RX-E100 7 Preset group A B C D E P1P2P3P4P5P6P7P8 CAUTION : When executing Test mode No. 2 RAM CLEAR, be sure to write down the preset memory contents of the tuner, using a table like the one shown below. Execution of RAM CLEAR will set the memory contents of the tuner back to the factory preset state which means that all the memories preset by the user will be erased. G FACTORY PRESET NOTE 1) PRESET PAGE. A : FMB : AMC : FMD : AM E : FM BAND FM (MHz) AM (kHz) MARKETS U, C, R(100k/10k) A, B, G, R,(50k/9k) U, C, R(100k/10k) A, B, G, R(50k/9k) 8 107.9 107.90 1440 1440 7 106.1 106.10 1350 1350 6 88.1 88.10 900 900 5 107.9 108.00 1710 1611 4 101.5 101.50 530 531 3 87.5 87.50 1400 1404 2 95.1 95.10 1080 1080 1 98.1 98.10 630 630 PRESET No. I AMP ADJUSTMENTS GConfirmation of Idling Current 1) No signal applied. 2) Non-loaded condition. 3) Aging is not neccessary. Note If the measured voltage exceeds 5mV, cut the lead wire of R197(L ch) or R204(R ch) and then check again if each measured value satisfies the rating. Item MAIN L MAIN R Test Poin R214 (Between terminal) R220 (Between terminal) Rating (DC) 0.1mV5mV Note) If R197(L ch) or R204(R ch) have already been cut off and idling current does not flow, reconnect R197(1k) or R204(1k). Q112 and Q115 are transistors f