Technics-SADA-15-Service-Manual电路原理图.pdf

Service Manual TOP NEXT Order No. MD0105119C1 A2 AV Control Stereo Receiver lSA-DA15 Color (K) . Black Type (N) . Gold Type PP . U.S.A. and Canada FM Tuner Section Frequency range87.9-107.9 MHz Sensitivity11.2 dBf (2V, IHF58) 50 dB quieting sensitivity MONO18.3 dBf (4.5V, IHF58) STEREO38.3 dBf (45V, IHF58) Total harmonic distortion MONO0.2% STEREO0.3% S/N MONO73 dB STEREO67 dB Frequency response20 Hz-15 kHz,+1 dB, -2 dB Alternate channel selectivity65 dB Capture ratio1.5 dB Image rejection at 98 MHz40 dB Spurious response rejection at 98 MHz75 dB AM suppression50 dB Stereo separation 1 kHz40 dB 10 kHz30 dB Antenna terminal75 (unbalanced) AM Tuner Section Frequency range530-1710 kHz Sensitivity20V, 330V/m Selectivity55 dB IF rejection (at 1000 kHz)50 dB Video Section Output voltage at 1 V input (unbalanced)10.1 Vp-p Maximum input voltage1.5 Vp-p Input/output impedance75 Amplifier Section Rated minimum sine wave RMS power output 20 Hz-20 kHz both channels driven 0.05% total harmonic distortion100 W per channel (6) 1 kHz continuous power output both channels driven 0.05% total harmonic distortion105 W per channel (6) Total harmonic distortion rated power at 20 Hz-20 kHz0.05% (6) half power at 1 kHz0.03% (6) Power bandwidth both channels driven, -3 dB10 Hz-100 kHz (6, 0.9%) Power output at the DVD 6CH operation 20 Hz-20 kHz (each channels driven) 0.05% total harmonic distortion Front2 x 100 W (6) Center100 W (6) Surround2 x 100 W (6) Low frequency damping factor30 (6) Load impedance pagina 1 van 2 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 2001 Matsushita Electronics (S) Pte. Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. TOP NEXT Front A or B4 - 8 A and B8 BI-WIRE6 - 8 Center6 - 8 Surround6 - 8 Frequency response PHONORIAA standard curve0.8 dB CD, DVD, TV, VCR1, VCR2, VCR3, TAPE10 Hz-100 kHz,3 dB Input sensitivity PHONO0.4 mV (3 mV, IHF66) CD, DVD, TV, VCR1, VCR2, VCR3, TAPE27 mV (200 mV, IHF66) S/N (IHF A) (VGCA ON) PHONO80 dB (80 dB, IHF66) CD, DVD (L/R/C/LS/RS), TV, VCR1, VCR2, VCR3, TAPE113 dB (IHF A, Rated Power, S=2 V) 90 dB (100 dB, IHF66) Input impedance PHONO47 k CD, DVD, TV, VCR1, VCR2, VCR3, TAPE22 k Tone controls BASS50 Hz,+10 to -10 dB TREBLE20 kHz,+10 to -10 dB Subwoofer frequency response (-6 dB)7 - 200 Hz General Power supplyAC 120 V, 60 Hz Power consumption400 VA 310 W Dimensions (W x H x D)430 x 158 x 370 mm (16-15/16” x 6-7/32” x 14-9/16”) Mass11.7 kg (25.8 lb.) Power consumption in standby mode:1 W DIN POWER (1 kHz T.H.D. 1%)2 X 100W (6) Notes: 1.Specifications are subject to change without notice./Mass and dimensions are approximate. 2.Total harmonic distortion is measured by the digital spectrum analyzer. * Manufactured under license from Dolby Laboratories.“Dolby”,“Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. * Manufactured under license from Digital Theater System.“DTS” and“DTS Digital Surround” are trademarks of Digital Theater System. pagina 2 van 2 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 1 Safety Precaution TOP PREVIOUS NEXT (This “Safety Precaution” is applied only in U.S.A.) 1. Before servicing, unplug the power cord to prevent an electric shock. 2. When replacing parts, use only manufacturers recommended components for safety. 3. Check the condition of the power cord. Replace if wear or damage is evident. 4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc. 5. Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the customer from being exposed to a shock hazard. lInsulation Resistance Test 1. Unplug the power cord and short the two prongs of the plug with a jumper wire. 2. Turn on the power switch. 3. Measure the resistance value with ohmmeter between the jumper AC plug and each exposed metal cabinet part, such as screw heads, antenna, control shafts, handle brackets, etc. Equipment with antenna terminals should read between 3M and 5.2M toall exposed parts*. (Fig 1) Equipment without antenna terminals should read approximately infinity to all exposed parts. (Fig 2) *Note: Some exposed parts may be isolated from the chassis by design. These will read infinity. 4. If the measurement is outside the specified limits, there is a possibility of a shock hazard. The equipment should be repaired and rechecked before it is returned to the customer. pagina 1 van 3 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. pagina 2 van 3 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. TOP PREVIOUS NEXT pagina 3 van 3 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 2 Before Repair and Adjustment TOP PREVIOUS NEXT Disconnect AC power, discharge Power Supply Capacitors C1702, C703C706, C742, C901, C904 through a 10 , 5 W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screw driver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid over current. Current consumption at AC 120 V, 60 Hz in NO SIGNAL mode should be 4501000 mA. TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 3 Protection Circuitry TOP PREVIOUS NEXT The protection circuitry may have operated if either of the following conditions are noticed: lNo sound is heard when the power is turned on. lStops during a performance. The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance ofthe amplifier are used. If this occurs, follow the procedure outlines below: 1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power once again after one minute. Note: When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again. TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 4 Accessories TOP PREVIOUS NEXT AC power supply cord. 1 pc. AM Loop Antenna Set/. 1 set. FM Indoor Antenna. 1 pc. Remote Control/Transmitter. 1 pc. TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 5.1 Front Panel TOP PREVIOUS NEXT TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 5.2 Remote Control TOP PREVIOUS NEXT TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 5 Front Panel Controls TOP PREVIOUS NEXT 5.1 Front Panel 5.2 Remote Control TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 6.1 Disassembly Procedure for each major P.C.B. TOP PREVIOUS NEXT Step 1 CS 3CA16OExternal ROM address for CS49326 4N.C.OTC9482 STB 5CLOCKOTC9482F Clock 6DATAOTC9482F Data 7N.C.IUnused/Free, Release internal pull-up for resistance 8N.C.IUnused/Free, Connect to GND through resistance 9INT2IUnused/Free, Connect to GND through resistance 10RESETIReset Input 11N.C.IUnused/Free, Release internal pull-up for resistance 12N.C.IUnused/Free, Release internal pull-up for resistance 13GND-GND 14XIN-4 MHz ceramic oscillation terminal 15XOUT-4 MHz ceramic oscillation terminal 16VDD-+5V 17N.C.IUnused/Free, Connect to GND through resistance 18N.C.IUnused/Free, Connect to GND through resistance 19N.C.IUnused/Free, Connect to GND through resistance 20N.C.IUnused/Free, Connect to GND through resistance 21OVLERRICS4226:OVLERR Overflow/error 22INTREQICS49326:INTREQ 23HOLDIPower failure detection, Power failure, Power on/Connectivity for H 24N.C.IUnused/Free, Release internal pull-up for resistance 25STB_SOTC9162/TC9163:STB Strobe 26CLK_SOTC9162/TC9163:CLK Serial clock 27DAT_SOTC9162/TC9163:DATA Serial data output 28MUTEA-GND 29N.C.OSoftware muting L:OFF H:ON 30N.C.Unused/Free Low output fixing 31N.C.IUnused/Free, Release, Connect to GND through resistance 32N.C.IUnused/Free, Release, Connect to GND through resistance 33N.C.OUnused/Free, Release H output pagina 2 van 3 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. TOP PREVIOUS NEXT 34N.C.OUnused/Free, Release H output 35N.C.OUnused/Free, Release H output 36N.C.OUnused/Free, Release H output 37N.C.OUnused/Free, Release H output 38N.C.OUnused/Free, Release H output 39N.C.OUnused/Free, Release H output 40N.C.OUnused/Free, Release H output 41N.C.OUnused/Free, Release H output 42N.C.OUnused/Free, Release H output 43N.C.OUnused/Free, Release H output 44N.C.OUnused/Free, Release H output 45N.C.OUnused/Free, Release H output 46N.C.OUnused/Free, Release H output 47N.C.OUnused/Free, Release H output 48N.C.OUnused/Free, Release H output 49N.C.OUnused/Free, Release internal pull-up for resistance H output 50N.C.OUnused/Free, Release internal pull-up for resistance H output 51N.C.OUnused/Free, Release internal pull-up for resistance H output 52N.C.OUnused/Free, Release internal pull-up for resistance H output 53N.C.OUnused/Free, Release internal pull-up for resistance H output 54EXT DACOInitialization diode, Internal pull-up resistance 55EXT RONOInitialization diode, Internal pull-up resistance 56DTS 2OInitialization diode, Internal pull-up resistance 57INITIInitialization diode, Reading input 58N.C.IUnused/Free, Connect to GND through resistance 59N.C.IUnused/Free, Connect to GND through resistance 60N.C.IUnused/Free, Connect to GND through resistance 61N.C.IUnused/Free, Connect to GND through resistance 62N.C.IUnused/Free, Connect to GND through resistance 63N.C.IUnused/Free, Connect to GND through resistance 64CDOUTICS4226:CDOUT Serial data input 65CS42OCS4226:CS Tip select 66SCLKOMain-Sub Serial clock output for communication 67TXDOMain-Sub Serial data output for communication 68RXD IMain-Sub Serial data input for communication 69/CS49OCS49326:CS CS49326 Tip select 70CCLKOCS49326/CS4226/CS4341:CCLK Serial clock 71CDINOCS49326/CS4226/CS4341:CDIN Serial data 72SCOUTICS49326:SCDOUT Serial data input 73AVSS-Power analaog for conversion of A/D, Connect to GND 74VREF-Reference voltage for conversion of A/D 75VOLUMEA/DVolume position detection for A/D 76REQSIMain-Sub Communication 77POWERODSP Power control L:ON H:OFF 78REQM OMain-Sub Communication 79PONOCD4226:PDN CS4226/CS4341 Reset 80CSRESETOCS49326:RESET CS49326 Reset pagina 3 van 3 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 9 Block Diagram TOP PREVIOUS NEXT TOP PREVIOUS NEXT pagina 1 van 1 29-11-2012file:/H:/Audio%20nieuw/T/Technics/viewing/SGML_VIEW_DATA/NA/SA-DA15. 8 -V Q352 11 15 14 DT SEL CK SEL ST SEL VIDEO A VIDEO B 2 D352D351 1 7 9 10 13 (3) 26X2 X1 X3 (2) 27 (4) 25 (5) 24 (6) 23 (7) 22 X4 X5 (9) 20 (10) 19 (12) 17 X7 X8 Level shift Latch circuit Shift register (11) 18 16 15 13 (8) 21X6 Vss 1 28 VDD REGULATOR 5 VIDEO C 6 VR502 REC_L LCH S301 S301 VR501(L) FRT_VCR2 DVD_LCH 16 +V Q351 REGULATOR+B CD VCR2 PHONO PB LCH RO LCH VCR REC (OUT) PLAY (IN) TAPE JK401 JK402 JK403 JK402 TV MONITOR OUT TV IN DVD IN VCR1 IN JK405 JK404 JK405 VCR1 OUT VCR2 VIDEO JK352 BUFFER AMP PHONO EQ AMP TONE AMP IC401 TC9163AN AUDIO SELECTOR IC503 NJM4580EDTE1 RCH IC451 AN6558F FROM IC901 TUNER MODULE VIDEO SELECTOR IC351 NJM2296D IC402 NJM4580EDTE1 -B -B +B JK352 VCR3 IN DVD LCH JK406 42 44 RX3 A OUT6 26 A OUT5 25 34 5689 10(13) 24-bit DSP PROCESSING RAM PROGRAM MEMORY RAM DATA MEMORY STC RAM INPUT BUFFER PLL CLOCK MANAGER DATA07 811, 1417 CMP DAT27 CMP CLK28 CMP REQ29 25SCLK N1 26LRCLK N1 22SDATA N1 CLK IN CLK SEL 30 31 FILTD FILTS 3233 MCLK 44 SCLK43 LRCLK42 AU DATA041 AU DATA140 AU DATA239 XMT9583 FILT 171940 +VA +VD CM OUT 1636 SCD OUT 19 EMWR 4 EXTMEN 2120 INTREQ 5 EMOE SCDIN 6 SCCLK 7 CS 18 RESET 36 INTREQ SCD OUT D OUT1 D IN3 32 D IN2 33 D IN1 34 30 31 MCLK OUT 37 LRCK SCLK 38 AUDATA0 AUDATA1 AUDATA2 X1001 (12.288MHz) SCLK SCLK LRCK LRCK A OUT3(4) 23 (24) CCLK CD OUT CD IN CS PDN AUDIO AIN1L(AIN1R) OVL/ERR CCLK CD OUT CD IN OVL/ERR PDN CS42 CS RESET CS49 43 RX1 RX2 AIN2L(AIN2R) A OUT1(2) 21 (22) Q1001 POWER 11(12) AIN1L 14 VSSA 35 VDDA 34 POWER SUPPLY AUDATA0 AUDATA1 AUDATA2 XMT958 XMT958 DIGITAL AUDIO INPUT INTERFACE FRAMER SHIFTER ROM PROGRAM MEMORY RAM DATA MEMORY INPUT BUFFER CONTROLLER RAM OUTPUT BUFFER OUTPUT FORMATTER PARALLEL OR SERIAL HOST INTERFACE COMPRESSED DATA INPUT INTERFACE SPDIF RECEIVER L_DSP A OUT MCLK MCLK XTI 28 AINAUX 15 CA18 IC1001 CS49326-CLR TV (OPTICAL) DVD (OPTICAL) CD (OPTICAL) JK1302 LOGIC CONTROL AC3/DTS DECODER BUFFER AMP BUFFER AMP BUFFER AMP IC1201 NJM4580EDTE1 IC1204 NJM4580EDTE1 INVERTER LOGIC CONTROL IC1006 SNAHC1U04DBV IC1005 SN74HCU04APW IC1003 SN74LV244APW LOGIC CONTROL IC1004 SN7AHCT244PW +B +B +B +B +B +B JK1301 JK1303 IC1002 C0FBZJ00004 DIR/DAC/VOL IC1206(1207) NJM2115D CS42 PDN POWER OVL/ERR OVL/ERR POWER PDN CS42 21776579 CS RESET 80 CS RESET CS49 CS49 69 SCD OUT 72 SCD OUT STB S CLK S DAT S 252627 22 24 23 X3 X4 X2-1 (21)8 4 3 SW CONT. CLK STB DATA 13 1516 C CLK CD OUT CD IN CCLK CD OUT CD IN 647071 INT REQ INTREQ 22 2 X1-1 X2-226 27 25 X1-2 10(19)X5 (20)9 X6-1 X OUT X IN 1514 CF1901 10 Q1901 RESET 23 HOLD CLOCK CK VR DATA DT VR 56 S CLK CM CK RXD CM DO 6667 TXD CM DI 68 REQS CM RQS 76 REQM CM RQM 78 ST SEL CK SEL DT SEL 9 INT2 57 INIT RESET Q1902,D1901 MUTEA 29 STATUS ST VR 4 MUTE_S C_IN DSP_SW STB S 75 VR501 (VR_PS) DSP_SW A OUT REC_L L_DSP RESET D_C CA18 1 CA18 DVD_LCH DVD SW TV DVD C JK407 JK406 BUFFER AMP SELECTOR BUFFER AMP BUFFER AMP IC1203 NJM4580EDTE1 IC1202 NJM4580EDTE1 IC406 NJM4580EDTE1 IC403 TC9162AN IC1901 M38B57M6170F SYSTEM CONTROL IC1205 NJM4580EDTE1 +B +B BUFFER AMP JK406 151416 4 (25) Lch IN (Rch IN) RL501 (D/A) Q511,Q513 (Q512,Q514) VR502 (BALANCE) RL502 (VGCA) RL503 (BI-AMP) RL504 D/A (LS) Q503 Q501 Q507,Q509 (Q508,Q510) Q502 MAIN_LIN MAIN_LS MUTE_S ST_VR CK_VR DT_VR RL505 (C) Q515 (Q516) DPASS C_IN DATA CK STB D/A D/A LCH D_C 23 SW_OUT SW_IN 22 10 SL_IN 3 L_OUT 9 SL_OUT C_OUT 6 C_IN 7 VR501 (C) L_OUT L_OUT L_DSP MUTING VR501 (SL) IC1209 NJM4580EDTE1 IC508 NJM4580DD MUTING IC504 NJM4580EDTE1 Q1201 MUTING RELAY DRIVE CONTROL RELAY DRIVE CONTROL RELAY DRIVE CONTROL RELAY DRIVE CONTROL SUBWOOFER OUT BUFFER AMP TONE AMP TONE AMP TONE AMP BUFFER AMP TONE AMP BUFFER AMP DVD SL JK407 BUFFER AMP TONE AMP M TONE AMP JK404 IC502 NJM4580EDTE1 IC405 NJM4580EDTE1 IC1210 NJM4580EDTE1 IC507 NJM4580DD IC1211 TC9428F SOUND CONTROLLER (VOLUME) IC1208 NJM4580EDTE1 IC506 NJM4580DD IC505 NJM4580DD RCH YC YC YC 7071727678 COM CK COM DO COM DI COM REQS COM REQM CM CK CM DO CM DI CM RQS CM RQM 79 VIDEO B 80 VIDEO A VIDEO B VIDEO A 10 RESET Q901 22 HOLD 60 VOL D