Studer-970-Service-Manual-Section-4电路原理图.pdf

Professional Audio System Components E48Date printed: 29.11.01 Technical Specifications Contact Ratings:max. 1 A/30 VDC or 0.3 A/125 VAC Note:In this application 48 V must not be exceeded to avoid shock hazard. Switching power60 VA (AC) 100 W (DC) Dimensions:Euro-card100 160 mm, 4 M units wide Ordering Information:Transistor-driven relays1.915.603.xx RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 Professional Audio System Components Date printed: 29.11.01E49 2.2.10 Dual Limiter1.915.700 In sound work there are numerous situations where the signal amplitude has to be limited to a pre-determined level in order to prevent overloading of succeeding equipment, such as light modulators in film work, or radio transmitters. With this limiter, excessive levels are automatically reduced to a preset level, and, since regulation is controlled by the programs en- ergy content, the performance of this limiter is free of any “pumping” ef- fects. Gain reduction is achieved with a Studer Voltage Controlled Ampli- fier (VCA) which ensures low noise performance and negligible distor- tion. Two identical, independent limiter circuits are contained on one Euro- card, plus additional, separate gain stages to drive peak program meters. The perfect tracking of the two VCAs makes this Dual Limiter suitable for stereo work as well, in which case a simple electrical connection is needed to link the units. Note:Gain reduction meters (not supplied) can be connected to the LINK out- puts as well, if required. Professional Audio System Components E50Date printed: 29.11.01 Technical Specifications Input:Impedance5.4 k, balanced configuration 2.7 k, unbalanced configuration Overload point+20 dBu (7.75 Vrms) Output:Impedance< 50 , unbalanced Frequency response+0/0.5 dB, 30 Hz.15 kHz +0/3 dB, 2 Hz.200 kHz Gain0 dB, limiter off Output noise level102 dBu, Limiter on 106 dBu, Limiter off Limiting ratio20:1 Threshold15 dBu.+3 dBu, adjustable Limited output level14 dBu.+4 dBu, depending on threshold setting Attack time1 ms Release time50 ms.5 s, program-dependent PPM Section: Output impedance 10 k Clipping point+24 dBu (12.3 V) Common mode rejection 50 dB, unbalanced to ground Output:balanced and floating Minimum permissible load200 Maximum output level +24 dBu (12.3 V) Frequency response0.2 dB, 30 Hz.60 kHz, equalization off THD 96 dB, equalizer off 93 dB, equalizer on (linear) Supply:15 V (80 mA idling, 170 mA +24 dBu into 200 ) Dimensions:Euro-card100 160 mm, 8 M units wide Ordering Information: Euro-cards:Line equalizer, horizontal, for recessed mounting1.915.776.xx Line equalizer, vertical, for recessed mounting1.915.777.xx Line equalizer, vertical, for flush mounting (ELMA)1.915.779.xx 19” standard productMounting frame (19”/1U) with power supply and front panel, wired for three equalizer cards 1.915.776 (not incl.)1.918.117.xx Professional Audio System Components E56Date printed: 29.11.01 2.2.13 Dual Balancing Unit/Dual Line Amplifier1.915.904 In professional audio work it is not uncommon that equipment with un- balanced input or output configuration must be connected to a system that is based on a strictly balanced design. The Dual Balancing Unit is the ideal component if the requirement of matching unbalanced to balanced equip- ment or vice versa has to be satisfied. The Dual Balancing Unit consists of one Euro-card which contains four separate circuits to accommodate unbalanced-to-balanced or balanced-to- unbalanced matching in a stereo system. It is the ideal choice for applica- tions in which consumer-type stereo equipment has to be integrated into a professional audio system, where balanced audio lines are a must. The Dual Balancing Unit will also be used in situations where balanced auxil- iary units must be connected to unbalanced insert points on a mixing desk. Professional Audio System Components Date printed: 29.11.01E57 The use of the balancing unit is not restricted to matching of balanced and unbalanced audio system components, because it can also be utilized as a (line) booster amplifier or as a stereo-to-mono mixer. By simply connec- ting the unbalanced outputs and inputs together and by adjusting again within the available ranges, two booster amplifiers with a maximum gain of 30 dB and a maximum output capability of +24 dBu*) can be realized. For stereo-to-mono mixing, the unbalanced sides of the amplifier sections simply are connected by means of combining (mixing) resistors, as shown in the diagram below. *)To avoid signal clipping, a system should always be designed in such a way that signal peaks stay well below an amplifiers maximum output ca- pacity. Alignment procedures and level settings depend to a large degree on the type of metering used in an audio system. When making measure- ments with a steady-state signal, a margin of 6 dB below a systems clip- ping point and the PPM deflected to “zero volume”, or a margin of 15 dB (for programs with extreme crest factors, even 20 dB) when utilizing a VU-meter, is considered good engineering practice. Professional Audio System Components E58Date printed: 29.11.01 Technical Specifications Balanced to unbalanced (Section 1): Input impedance 10 k, balanced/floating Maximum input level+24 dBu Output impedance 100 dB; attenuation set to 6 dB, line level +6 dBu Unbalanced to balanced (Section 2): Input impedance5 k, unbalanced Maximum input level+20 dBu Output impedance 50 , balanced/floating Minimum load200 Maximum output level+24 dBu Frequency response0.2 dB, 30 Hz.16 kHz Gain14/30 dB; two fixed steps 0.17 dB; variable S/N 100 dB; gain set to 6 dB, line level +6 dBu Supply:15 V (70 mA, idling; 170 mA, each channel +24 dBu into 200 ) Dimensions:Euro-card100 160 mm, 7 M units wide Ordering Information: Euro-card:Dual balancing unit1.915.904.xx 19”/1U standard products:2CH balancing unit (1 1.915.904)75.700.89212 4CH balancing unit (2 1.915.904)75.700.89422 6CH balancing unit (3 1.915.904)75.700.89632 Professional Audio System Components Date printed: 29.11.01E59 2.3 Racks and Frames 2.3.1 19” Mounting Frame for 3 Euro-Cards1.918.100 This 19” mounting frame (height: 44.5 mm/1U) offers space for three Euro-cards next to the power supply. The power supply provides 15 VDC (regulated) and 24 VDC (unregulated). The frame comes equipped with three edge connectors to accommodate three Euro-cards horizontally, side by side. A blank back panel of ano- dized aluminium is provided and permits the installation of input and out- put connectors as required, depending on the application. Professional Audio System Components E60Date printed: 09.01.02 Technical Specifications Primary:Voltage selector for100, 120, 140, 200, 220, 240 VAC Fuse (slow-blow)400 mA (for 100.140 VAC) 200 mA (for 200.240 VAC) Secondary:Regulated voltage15 VDC, 0.5 A max. Unregulated voltage24 VDC, 0.2 A max. (for signaling) Fuses (slow-blow)2 1 A Ordering Information: 19”/1U standard productMounting frame for three Euro-cards with power supply and stabilizer PCB, with two blank aluminium back panels (1.918.100.21)1.918.100.xx Alternative Back Panels:The mounting frame 1.918.100.xx can be equipped with the following back panels: Ordering Information: Alternative Back Panels for Mounting Frame 1.918.100 Steel back panel for 15 XLR sockets (Neutrik)1.918.113.03 Alternative Back Panels for Blank Panels 1.918.100.21 Aluminium back panel for 6 XLR sockets (Neutrik)1.918.100.36 Aluminium back panel for 1 Siemens 30/39 pin and 1 15pin D-type sockets20.020.402.00 Aluminium back panel for 2 Siemens 30/39 pin sockets1.918.100.33 Mechanical interface Siemens panel D-type connector: see chapter 2.3.4. XLRXLR 123456789101112131415MAINS 123456 XLRXLR MAINS BLANK PANEL 1.918.100.21 BLANK PANEL 1.918.100.21 1.918.100.361.918.100.33 1.918.113.03 1.918.100.01 15p D SIEMENS 30/39p 20.020.402.00 SIEMENS 30/39p SIEMENS 30/39p Professional Audio System Components Date printed: 29.11.01E61 2.3.2 19” Ventilation Unit/19” Blank Panels1.918.119/0XX When filling a cabinet rack with various electronic equipment, consider- able heat may be generated, which could be harmful to other nearby com- ponents. To provide for sufficient convection cooling, the use of ventila- tion units above and below the heat-generating equipment is strongly rec- ommended. A ventilation unit consists of a 19” wide and 1U high sheet metal struc- ture, which extends about 340 mm into the rack. The units front section is perforated, with a slanting metal panel mounted inside. By installing the ventilation unit with that panel either slanting upwards or downwards, the air flow can be directed as desired. If only moderate heat problems have to be coped with, it may be sufficient to use one ventilation unit above or below the heat source, and to provide sufficient spacing from adjacent equipment by installing a 1U blank panel on the opposite side. Ordering Information: 19” Ventilation Units Ventilation unit 19”/1U1.918.119.xx Ventilation unit without air guide panel1.918.119.09 19” Blank Panels Blank panel 19”/1U high, anodized finish1.918.001.xx Blank panel 19”/2U high, anodized finish1.918.002.xx Blank panel 19”/3U high, anodized finish1.918.003.xx Blank panel 19”/1U high, plastic coated, grey1.918.001.09 Blank panel 19”/2U high, plastic coated, grey1.918.002.09 Blank panel 19”/3U high, plastic coated, grey1.918.003.09 Blank panel 19”/1U high, paint finish, grey1.918.011.xx Blank panel 19”/2U high, paint finish, grey1.918.012.xx Blank panel 19”/3U high, paint finish, grey1.918.013.xx Professional Audio System Components E62Date printed: 29.11.01 2.3.3 19” Euro-Card Mounting Frames1.918.318/319 The Euro-card mounting frame (sometimes also referred to as 19” Sub Rack) is an empty structure which fits into any standard 19” rack. It is in- tended to accommodate PCBs of the Euro format vertically, side by side. The available space within the sub rack is divided into 84 Modular Widths, each measuring 5.08 mm (0.2 inches). One Euro-card usually oc- cupies 7 M (Module) widths, thus up to 12 Euro-cards may be installed. The Euro-card frame is supplied as a kit for assembly by the user. Assem- bly instructions are included with each kit. Supplied with the kit is a hinged front panel of anodized aluminium, pro- viding quick access to the plug-in PCBs if required. This front panel and its hinges are available separately in case a damaged panel or hinge needs to be replaced. Separate edge connectors and slide rails are required for each Euro-card and power supply unit installed into the Euro-card frame. Mounting kits containing the slide rails, edge connectors, and other accessories are de- scribed below (1.918.315/316). To provide for convection cooling within an equipment rack, the Ventila- tion Unit 1.918.119.xx is recommended. Euro-Card Racks, Ordering Information: Euro-card frame (19”/3U, ELMA), direct access to 32pin connectors on back panel1.918.318.xx Euro-card frame (19”/3U, ELMA) with additional rear panel, for max. 10 freely assignable connector panels1.918.319.xx Professional Audio System Components Date printed: 29.11.01E63 2.3.4 19” Euro-Card Mounting Accessories Euro-Card Mounting KitFor installing Euro-cards and/or a power supply unit into a Euro-card frame 1.918.318/319, suitable edge connectors and guide rails are required. Euro-Card Mounting Kit, Ordering Information: Mounting kit for 1 Euro-card (ELMA rack); see photograph1.918.315.xx Mounting kit for power supply 1.915.1001.918.316.xx Connector Panels:The connector panels fit into the Euro-card frame with back panel (1.918.319). Please order the suitable panels separately. Professional Audio System Components E64Date printed: 09.01.02 Connector Panel (3U high) Ordering Information: Blank panel1.918.319.21 Panel for Siemens connector (cut out 18 67 mm) *1.918.319.22 Panel for mains inlet and 2 banana sockets1.918.319.23 Panel for 4 XLR sockets1.918.319.24 * Siemens Connector Sets:Including male and female connector: Siemens 30pin, without connector panel1.900.080.xx Siemens 39pin, without connector panel1.900.081.xx * D-Type Adapter Panels:The Siemens connector panel can be used as a base for mounting a D-type connector adapter panel. The adapter sets listed below include male and female connectors, connector cover, bolting spring, clamp, and adapter panel: Adapter Panel Ordering Information: The adapter kits consist of male and female D-type connector, metal or plastic connector cover, adapter panel, and mounting hardware, to fit on the Siemens connector panels 1.918.319.22 (for 3U frames) or 1.918.100.33 (for 1U frames): D-type set, 9pin, metal connector cover1.900.075.xx D-type set, 15pin, metal connector cover1.900.076.xx D-type set, 25pin, metal connector cover1.900.077.xx D-type set, 37pin, metal connector cover1.900.078.xx D-type set, 50pin, metal connector cover1.900.079.xx D-type set, 9pin, plastic connector cover1.970.075.xx D-type set, 15pin, plastic connector cover1.970.076.xx D-type set, 25pin, plastic connector cover1.970.077.xx D-type set, 37pin, plastic connector cover1.970.078.xx D-type set, 50pin, plastic connector cover1.970.079.xx Professional Audio System Components Date printed: 29.11.01E65 Extension Board:For alignment and repair, a Euro-card may have to be operated outside the mounting frame. To facilitate any service work that has to be performed on individual cards, extending the cards 32 electrical connections is pos- sible by means of a flexible extension board. Ordering Information:Extension PCB for Euro-cards, 2 32pin, flexible1.228.327.82