Sony-SCD-XA5400ES-Service-Manual电路原理图.pdf

SERVICE MANUAL Sony Corporation Audio&Video Business Group Published by Sony Techno Create Corporation SCD-XA5400ES SPECIFICATIONS SUPER AUDIO CD PLAYER 9-889-205-01 2008H05-1 2008.08 US Model Canadian Model AEP Model Ver. 1.0 2008.08 Model Name Using Similar MechanismNEW Mechanism TypeCDM66F-DVBU101 Optical Pick-up Block NameKHM-313CAB When a Super Audio CD is played Playing frequency range2 Hz to 100 kHz Frequency response2 Hz to 50 kHz (3 dB) Dynamic range110 dB or more Total harmonic distortion rate 0.0012 % or less Wow and flutterValue of measurable limit (0.001 % W. PEAK) or less When a CD is played Frequency response2 Hz to 20 kHz (0.5 dB) Dynamic range100 dB or more Total harmonic distortion rate 0.0017 % or less Wow and flutterValue of measurable limit (0.001 % W. PEAK) or less General Laser Diode Properties Emission duration: Continuous Laser Output*: Less than 44.6 W * This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Power requirementsNorth America: 120 V AC, 60 Hz Europe: 230 V AC, 50/60 Hz Power consumption25 W Power consumption (during standby mode) 0.5 W Dimensions (w/h/d)430 124 390 mm (17 5 15 3/8 inch) incl. projecting parts Mass (approx.)10.2 kg (22 lb 8 oz) Supplied accessories Audio connecting cordRed and White plugs (1) Remote commanderRM-ASU042 (1) AC power cord (1) BatteryR6 (size-AA) (2) Design and specifications are subject to change without notice. Output jacks * Outputs only the audio signals of the CD Jack typeOutput level Load impedance ANALOG OUT UN- BALANCED Phono jacks 2 Vrms (at 50 kilohms) Over 10 kilohms ANALOG OUT BALANCED XLR2 Vrms (at 50 kilohms) Over 600 ohms HDMIHDMI DIGITAL OUT (CD) OPTICAL* Square optical output connector 18 dBm(Light emitting wave length: 660 nm) DIGITAL OUT (CD) COAXIAL* Coaxial output connector 0.5 Vp-p75 ohms PHONESStereo phone jack 5 mW32 ohms RadioFans.CN 收音机爱 好者资料库 SCD-XA5400ES 2 NOTES ON CHIP COMPONENT REPLACEMENT Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. FLEXIBLE CIRCUIT BOARD REPAIRING Keep the temperature of soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONET WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DON- NS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. CAUTION Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radia- tion exposure. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. RadioFans.CN 收音机爱 好者资料库 SCD-XA5400ES 3 1. SERVICING NOTES . 4 2. GENERAL . 6 3. DISASSEMBLY 3-1. Disassembly Flow . 8 3-2. Case . 8 3-3. Loading Panel Assy . 9 3-4. Front Panel Assy . 9 3-5. MAIN Board . 10 3-6. Mechanism Deck (CDM66F-DVBU101) . 10 3-7. MOTOR Board, Motor (L) Assy (Loading) . 11 3-8. Base Unit Block . 11 4. TEST MODE . 12 5. ELECTRICAL ADJUSTMENT . 16 6. DIAGRAMS 6-1. Block Diagram - SA-CD/CD SERVO Section - . 17 6-2. Block Diagram - HDMI Section - . 18 6-3. Block Diagram - MAIN Section - . 19 6-4. Block Diagram - PANEL, POWER SUPPLY Section - . 20 6-5. Printed Wiring Board - MAIN Section (1/2) - . 22 6-6. Printed Wiring Boards - MAIN Section (2/2) - . 23 6-7. Schematic Diagram - MAIN Section (1/4) - . 24 6-8. Schematic Diagram - MAIN Section (2/4) - . 25 6-9. Schematic Diagram - MAIN Section (3/4) - . 26 6-10. Schematic Diagram - MAIN Section (4/4) - . 27 6-11. Printed Wiring Board - AUDIO Section (1/2) - . 28 6-12. Printed Wiring Boards - AUDIO Section (2/2) - . 29 6-13. Schematic Diagram - AUDIO Section (1/2) - . 30 6-14. Schematic Diagram - AUDIO Section (2/2) - . 31 6-15. Printed Wiring Boards - PANEL Section - . 32 6-16. Schematic Diagram - DISPLAY Board - . 33 6-17. Schematic Diagram - KEY Section - . 34 6-18. Schematic Diagram - POWER Board - . 35 6-19. Schematic Diagram - STANDBY Board - . 36 6-20. Printed Wiring Boards - POWER Section - . 37 7. EXPLODED VIEWS 7-1. Case Section . 47 7-2. DISPLAY Board Section . 48 7-3. Front Panel Section . 49 7-4. MAIN Board Section . 50 7-5. AUDIO Board Section . 51 7-6. Chassis Section . 52 7-7. Mechanism Deck Section (CDM66F-DVBU101) . 53 7-8. Base Unit Section . 54 8. ELECTRICAL PARTS LIST . 55 Accessories are given in the last of the electrical parts list. TABLE OF CONTENTS SCD-XA5400ES 4 SECTION 1 SERVICING NOTES ModelPart No. US and Canadian models3-873-299-1 AEP model3-873-299-2 UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to fl ow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostat- ic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The fl exible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc refl ective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. NOTE OF REPLACING THE IC1103 ON THE MAIN BOARD IC1103 on the MAIN board cannot exchange with single. When this part is damaged, exchange the entire mounted board. MODEL IDENTIFICATION Rear View Part No. You can play the following types of discs on this player. Super Audio CDs Audio CDs DSD Discs This player cannot play the following discs. CD-ROMs (MP3, JPEG, etc.) DVDs DTS-CDs DualDiscs, etc. If you try to play CD-ROMs/DVDs, the error message “Cannot Play” or “No Disc” will appear. For DTS-CDs/DualDiscs, refer to their respective notes below. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. Notes on CD-R/CD-RW playback Discs recorded on CD-R/CD-RW drives may not be played back because of scratches, dirt, recording condition, or the drives characteristics. Besides, the discs, which are not yet finalized at the end of recording, cannot be played back. In these cases, “Reading” will remain or “Cannot Play” will appear on the display. Note on DTS-CDs DTS signals are output from the DIGITAL OUT (CD) jacks only. The DTS signals must be decoded on a DTS-compliant digital device to be listened to. Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. Note on DSD Discs A DSD Disc is a disc recorded in the DSF file format. This player can play DSF files that you have recorded on DVD-ROM compatible DVD-R, DVD-RW, DVD+R and DVD+RW discs. For details on DSD Discs. Compatib e Disc Types SCD-XA5400ES 5 ? Pull out the tray in the direction of arrow ?. ? Rotate the cam (66) with a tapering driver in the direction of arrow ?. cam (66) BOTTOM VIEW ? ? HOW TO OPEN THE TRAY WHEN POWER SWITCH TURNS OFF connect jig (extension cable J-2501-102-A) to MAIN board (CN501, CN1100) and AUDIO board (CN151, CN152). MAIN board (CN501) AUDIO board (CN152) MAIN board (CN1100) AUDIO board (CN151) insulator sheet Note: insert the insulator sheet to prevent short. CAUTION Be sure to execute a solder bridge as a measure against static electricity when removing the optical pick-up or DMB-FIT board. (Otherwise, the OP block will be destroyed.) mechanism deck BOTTOM VIEW MAIN BOARD SERVICE POSITION In checking the MAIN board, prepare jig (extension cable J-2501-102-A: 1 mm Pitch, 13 cores, Length 300 mm). PRECAUTION WHEN REMOVING OPTICAL PICK-UP BLOCK OR DMB-FIT BOARD SCD-XA5400ES 6 SECTION 2 GENERAL This section is extracted from instruction manual. Front Panel ? ?/? (power) switch Turns the power of the player on or off To let the player enter power-saving mode (standby mode), press ?/? (power) on the remote or on the player ? TIME/TEXT button Switches the playing time of the track, the remaining time of the disc, or TEXT information on the display ? MULTI/2CH button Selects the playback area when a disc with the 2- channel area and the multi-channel area (page 8) is loaded ? SA-CD/CD button Switches between the Super Audio CD layer and the CD layer of a hybrid disc ? HDMI button/lamp Sets whether the audio signal is output from the HDMI OUT jack or not When the lamp is lit, sound is output from the HDMI OUT jack When the lamp is not lit, sound is output from the ANALOG OUT jacks and DIGITAL OUT (CD) jacks ? Disc tray Holds a disc ? ? button Opens and closes the disc tray ? ? button and lamp Plays a disc The lamp lights up during playback ? ? button and lamp Pauses playback The lamp lights up during playback pause ? ? button Stops playback ? ? AMS ? dial (AMS: Automatic Music Sensor) Selects a track ? Display window Displays information on the disc or current track ? Remote sensor Receives the signal from the remote ? PHONE LEVEL Adjusts the headphones volume ? PHONES jack Connects the headphones Rear Panel ? IR REMOTE IN jack Equipped on the models for the U S and Canada only Connects an IR repeater ? ANALOG OUT BALANCED L/R jacks Connects a component with XLR input jacks, such as stereo amplifiers, etc , using an XLR (balanced) cable (not supplied) ? HDMI PRIORITY MULTI/2CH switch When both multi-channel area and 2-channel area are recorded on a Super Audio CD layer, sets the area that is given priority to be played back ? HDMI OUT jack Connects components with HDMI jacks, such as HDMI-compliant amplifiers, etc ? DIGITAL OUT (CD) COAXIAL jack Connects a component with the coaxial digital input jack, such an MD deck, etc ? DIGITAL OUT (CD) OPTICAL jack Connects a component with the optical digital input jack, such an MD deck, etc ? DIGITAL OUT (CD) ON/OFF switch Sets whether audio signals are output from the DIGITAL OUT (CD) jacks or not ? AC IN jack Connects the supplied AC power cord (mains lead) ? ANALOG OUT UNBALANCED L/R jacks Connects a component with analog input jacks, such as stereo amplifiers, etc , using an audio co