Sony-RCD-W100-Service-Manual电路原理图.pdf

2003 Sony Corporation Operating Instructions Owners Record The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No.Serial No. 4-246-076-11(1) Compact Disc Recorder RCD-W500C/W100 RadioFans.CN 收音机爱 好者资料库 2 WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths, curtains, etc. And dont place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. This appliance is classified as a CLASS 1 LASER product. This label is located on the rear exterior. CAUTION CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance For the customers in the U.S.A. Dont throw away the battery with general house waste, dispose of it correctly as chemical waste. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. As the laser beam used in this unit is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. For the customers in Canada This Class B digital apparatus complies with Canadian ICES-003. CAUTION TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. RadioFans.CN 收音机爱 好者资料库 3 Table of Contents Getting Started Unpacking . 6 Hooking Up the System . 6 This Unit Can Use the Following Discs 7 Basic Operations Playing a CD . 8 Playing a disc with MP3 files. 9 Using the Display . 13 Locating a Specific Track. 15 Locating a Particular Point in a Track . 16 Playing Tracks/Discs Repeatedly (Repeat Play) .17 Playing in Random Order (Shuffle Play) . 18 Creating Your Own Program (Program Play) .19 Recording/Editing Before Recording . 20 Synchro-Recording a CD to CD-R or CD-RW . 22 Recording on a CD-R or CD-RW Manually .25 Adjusting the Recording Level. 27 Marking Track Numbers While Recording . 28 Fading In and Out recording (Rec Fader). 29 Finalizing a CD-R or CD-RW. 29 Unfinalizing a CD-RW. 30 Erasing Tracks of a CD-RW .31 Labeling Tracks/Discs . 32 Useful Tips for Recording .33 Additional Information Using the Setup Menu . 35 Messages . 36 Self-diagnosis Function .37 System Limitations. 38 Troubleshooting.38 Specifications .Back cover 4 On condensation in the unit If the unit is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the unit. Should this occur, the unit may not operate properly. In this case, remove the CD, CD-R, or CD-RW and leave the unit turned on for about an hour until the moisture evaporates. On handling discs To keep the disc clean, handle it by its edge. Do not touch the surface. Do not stick adhesive papers or tapes onto the disc. If there is glue or a similar substance on the disc, remove it completely before using the disc. On storage Do not expose the disc to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. Store discs in their cases. Do not store discs either stacked horizontally or standing vertically without their cases. On cleaning Fingerprints or dust on the disc may cause poor sound reproduction or sound dropout. Before playing a disc, clean it with a cleaning cloth. Wipe the disc from the center out. If the disc is still dirty after being wiped with a cleaning cloth, wipe it again with a slightly moistened cloth. Then wipe off the residual moisture with a dry cloth. Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for vinyl LPs. Welcome Thank you for purchasing this Sony Compact Disc Recorder. Before operating the unit, please read this manual thoroughly and retain it for future reference. About This Manual The instructions in this manual are for 2 models: RCD-W500C and RCD-W100. RCD-W500C is the model used for illustration purposes. Conventions Instructions in this manual describe the controls on the unit. You can also use the controls on the remote if they have the same or similar names as those on the unit. The following icon is used in this manual: Z Indicates that you can do the task using the remote. Precautions On safety Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further. The use of optical instruments with this product will increase eye hazard. On power sources Before operating the unit, check that the operating voltage of the unit is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the unit. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. If you are not going to use the unit for a long time, be sure to disconnect the unit from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. AC power cord must be changed only at the qualified service shop. 5 Note on High-Speed Synchro-Recording When recording a CD, certain conditions may cause the sound to dropout, noise in the recording, or even unwanted tracks on the CD-R or CD-RW. If this happens, clean the CD as described in “On cleaning” above, and record to the CD-R or CD-RW using normal speed Synchro-Recording only. Note on CD-R or CD-RW playback Playback of a CD-R or CD-RW recorded by a CD-R or CD-RW recorder may not be possible depending on the recording conditions (e.g., dirty disc, etc.). Also, please note that you need to finalize a CD-R or CD-RW before playing it back on DECK A of this unit or a system other than the one used to make the recording. (Finalizing is a process to complete the recording.) After finalizing a CD-R, you can play it in any conventional CD player. However, depending on the state of the recording, the sound may skip during playback. After finalizing a CD-RW, you can play it in a CD-RW compatible player only. Music discs encoded with copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. Note on discs With the following kinds of discs, you may experience a reading failure or noise when recorded to a CD-R or CD-RW. Discs with adhesive labels attached to them Irregularly shaped discs (for example, heart or star shaped) Discs with heavy printing on only one section (may effect the balance of the disc in the disc tray) Old discs Scratched discs Dirty discs Warped discs 6 Hooking Up the System This section describes how to hook up the unit to an amplifier. Be sure to turn off the power of each component before making the connections. Connecting the unit to an amplifier Connect the amplifier to the ANALOG IN/ OUT jacks using the audio connecting cords (supplied), making sure to match the color- coded pins to the appropriate jacks on the components: red (R) to red and white (L) to white. Be sure to make connections firmly to prevent hum and noise. Connecting the unit to a digital component Connect a component such as digital amplifier, CD player, DAT deck, or MD deck through the DIGITAL OPTICAL IN/OUT jacks (S/PDIF square type) with a optical digital cord (not supplied). Be sure to insert the plug until it clicks into place. Optical digital cord (not supplied) RCD-W500C/W100 Amplifier ANALOG IN L R OUT TAPE/MD L R INOUT White (L)White (L) Red (R)Red (R) Audio connecting cords (supplied) (2) ll: Signal flow Unpacking Check that the following items are included: Audio connecting cords Phono plug 2 (red/white) y Phono plug 2 (red/white) (2) Remote commander (remote) (1) R6 (size AA) batteries (2) Inserting batteries into the remote You can control the unit using the supplied remote. Insert two R6 (size AA) batteries by matching the 3 and # ends on the batteries to the markings inside the compartment. When using the remote, point it at the remote sensor on the unit. Tip With normal use, the batteries should last for about six months. When the remote no longer operates the unit, replace both batteries with new ones. Notes Do not leave the remote near an extremely hot or humid place. Do not drop any foreign object into the remote casing, particularly when replacing the batteries. Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a malfunction. If you dont use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Getting Started 7 Getting Started Connecting the AC power cord Connect the AC power cord to a wall outlet. Notes Be sure to place the player on a flat, horizontal place. If the player is left on a slanted position, it may cause a malfunction or damage the player. If the following occurs during CD playback or recording, a reading error may occur or noise may be produced in the recorded results: The disc tray or other part of the system is bumped. The system is placed on an uneven or soft surface. The system is located near a speaker, door, or other source of vibration. This Unit Can Use the Following Discs The unit can use three types of discs as follows: Audio CDs Discs with these logos can be played by both DECK A (the CD player section) and DECK B (the CD-R or CD-RW recording section) of the unit. Audio CD-R Discs with this logo are recordable only one time. When you finalize the disc (page 29), you can play it in either DECK A (the CD player section) or DECK B (the CD-R or CD-RW recording section), or any conventional CD player (you may not be able to play it in some CD players), including home, car, and portable models. (An unfinalized disc can be played only in DECK B.) When you buy a CD-R, please note that you must buy an audio CD-R. A CD-R designed for computer use will not work in this unit. Audio CD-RW Discs with this logo are recordable, and also re-writable. When you finalize the disc (page 29), you can play it in either DECK A (the CD player section) or DECK B (the CD-R or CD- RW recording section), and CD-RW compatible players. They will not play back in most current CD players unless the player is CD-RW compatible. (An unfinalized disc can be played only in DECK B.) When you buy a CD-RW, please note that you must buy an audio CD-RW. A CD-RW designed for computer use will not work in this unit. This logo means that an unit is compatible with Audio CD-R and Audio CD-RW (both Audio CD-R and Audio CD-RW can be used). Note On this player, you can play MP3 files on DECK A only. For details, see “Playing a disc with MP3 files” on page 11. 8 Playing a CD This unit has two decks. In this manual, the CD player section is just called DECK A, and the CD-R and CD-RW recording section is called DECK B. When using the remote, set DECK A/DECK B to DECK A to operate DECK A (the CD player section), or to DECK B to operate DECK B (the CD-R or CD-RW recording section). 1Turn on your amplifier and adjust the volume to the minimum. 2Set your amplifiers input selector to select this unit. 3Press POWER. 4Press OPEN/CLOSE (or one of the DISC 1-5 A buttons for DECK A of RCD- W500C) and place a disc on the inner circle of DECK A (or B). Press OPEN/ CLOSE (or A) again to close the disc tray. 5For DECK A of RCD-W500C, press PLAY MODE repeatedly to select the Continuous play mode. When you select ALL DISCS 1 DISC/ ALBUM Basic Operations The unit plays All discs in the unit consecutively in the order of the disc number. Only one disc you have selected. 6Press H. The unit starts playing. Adjust the volume on the amplifier. To Stop playback Pause playing Select the disc (for DECK A of RCD-W500C) Go to the next disc (for DECK A of RCD-W500C) Z Go to the next track Go to the beginning of the current track or the preceding track Remove the disc *AMS: Automatic Music Sensor Tips You can start playing from a specific track in step 6 1 Turn AMS while the ALBUM SELECT indicator in the display is turned off (or press ./ or the number buttons on the remo