Sony-CDP-CE575-Service-Manual电路原理图.pdf

SERVICE MANUAL COMPACT DISC PLAYER US Model Canadian Model AEP Model SPECIFICATIONS CDP-CE575 Ver 1.1 2001.07 9-929-586-12Sony Corporation 2001G0500-1Home Audio Company C 2001.7Shinagawa Tec Service Manual Production Group Model Name Using Similar MechanismNEW CD Mechanism TypeCDM59-5BD27 Base Unit NameBU-5BD27 Optical Pick-up NamePXR-104X Compact disc player LaserSemiconductor laser ( = 780 nm) Emission duration: continuous Frequency response2 Hz to 20 kHz 0 5 dB Dynamic rangeMore than 93 dB Harmonic distortionLess than 0 0045% Outputs ANALOG OUT DIGITAL OUT (OPTICAL) PHONES General Power requirements120 V AC, 60 Hz Power consumption11 W Dimensions (approx )430 x 110 x 400 mm (w/h/d)(17 x 4 3/8 x 15 3/4 in ) incl projecting parts Mass (approx )5 2 kg (11 lbs 8 oz) Supplied accessories Audio cord (2 phono plugs 2 phono plugs) (1) Remote commander (remote) (1) R6 (size AA) batteries (2) Design and specifications are subject to change without notice. Load impedance Over 10 kilohms Wave length: 660 nm 32 ohms Jack type Phono jacks Optical output connector Stereo phone jack Maximum output level 2 V (at 50 kilohms) 18 dBm 10 mW RadioFans.CN 收音机爱 好者资料库 2 CDP-CE575 SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground TABLE OF CONTENTS 1.SERVICEING NOTES.3 2.GENERAL.6 3.DISASSEMBLY 3-1.Disassembly Flow .8 3-2.Case (409538) .9 3-3.Front Panel Section .9 3-4.CD Mechanism Deck (CDM59-5BD27). 10 3-5.MAIN Board . 10 3-6.Base Unit (BU-5BD27). 11 3-7.Table Assy . 11 3-8.Sensor Board . 12 3-9.Loading Motor Board . 12 4.ASSEMBLY. 13 5.TEST MODE. 14 6.ELECTRICAL ADJUSTMENTS. 18 7.DIAGRAMS 7-1.Note for Printed Wiring Boards and Schematic Diagrams . 21 7-2.Printed Wiring Board BD Section . 22 7-3.Schematic Diagram BD Section . 23 7-4.Printed Wiring Boards MOTOR/SENSOR Section . 24 7-5.Schematic Diagram MOTOR/SENSOR Section . 25 7-6.Schematic Diagram MAIN Section (1/2) . 26 7-7.Schematic Diagram MAIN Section (2/2) . 27 7-8.Printed Wiring Boards MAIN Section . 28 7-9.Printed Wiring Boards DISPLAY Section . 30 7-10. Schematic Diagram DISPLAY Section . 31 7-11. IC Pin Function Description . 32 8.EXPLODED VIEWS 8-1.Case Section . 36 8-2.Front Panel Section . 37 8-3.Chassis Section . 38 8-4.CD Mechanism Deck Section-1 (CDM59-5BD27) . 39 8-5.CD Mechanism Deck Section-2 (CDM59-5BD27) . 40 8-6.Base Unit Section (BU-5BD27) . 41 9.ELECTRICAL PARTS LIST. 42 ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. Ver 1.1 2001.07 RadioFans.CN 收音机爱 好者资料库 3 CDP-CE575 SECTION 1 SERVICING NOTES The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emis- sion, observe from more than 30 cm away from the objective lens. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT MODEL IDENTIFICATION BACK PANEL ModelPart No. US model4-233-720-0s Canadian model4-233-720-1s AEP model4-233-720-2s HOW TO OPEN THE DISC TABLE WHEN POWER SWITCH TURNS OFF Insert a tapering driver into the aperture of the unit bottom, and turn it in the direction of the arrow (to OUT direction). table tapering driver *To close the disc table, turn the tapering driver in the reverse direction (to IN direction). Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur- ing repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. NOTES ON CLEANING OF OPTICAL PICK-UP LENS Do not clean up the optical pick-up lens. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure. Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times. LASER DIODE AND FOCUS SEARCH OPERATION CHECK This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. Part No. 4 CDP-CE575 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display. To check, perform the following procedure. Checking Method: 1. Set the test disc on a free tray, and chuck the disc. 2. Press the H button and playback the disc. 3. The following will be displayed on the fluorescent indicator tube. Display : 1kHz/0 dB/ L ?(38h to 3Fh) A B C D E F G(40h to 47h) H I J K L MNO(48h to 4Fh) P QR S T U VW(50h to 57h) X Y Z _(58h to 5Fh) a b c d e f g(60h to 57h) h i j k l m n o(68h to 6Fh) p q r s t u v w(70h to 77h) x y z I (78h to 7Fh) i (A0h to A7h) 8859-1 9C PR (A8h to AFh) 23 (B0h to B7h) 1 (B8h to BFh) (C0h to C7h) (C8h to CFh) D (D0h to C7h) Y(D8h to DFh) (E0h to E7h) (E8h to FFh) (F0h to F7h) y(F8h to FFh) No.66 No.67 to No.99 TRACK No. Recorded contentsDisplay T All the same T All the same T All the same T All the same T All the same T All the same T All the same X Y Z _ (58 T All the same T All the same T All the same T All the same (A0 i are not displayed (A8 (B0 (B8 (C0 (C8 (D0 (D8 (E0 are not displayed (E8 are not displayed (F0 are not displayed (F8 yare not displayed T All the same T All the same to T All the same * 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 to 99 1 4 1 2 3 4 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) 6 CDP-CE575 SECTION 2 GENERAL This section is extracted from instruction manual. 4 CHECK qh (13) CLEAR qj (13, 14, 16, 17) CONTINUE 2 (9, 13, 15, 18) DISC 15 3 (9, 10, 13) Disc compartment ws (9) DISC SKIP 9 (9, 12, 13) Display 4 (11) EX-CHANGE 8 (12, 15) FADER ql (14, 20) MEGA CONTROL 0 (18, 19) MENU wf (8, 16, 17) PEAK SEARCH qk (15) PHONES jack wh (10) POWER 1 (7, 9, 16) PROGRAM qd (9, 13, 18) Remote sensor wa (6) REPEAT qf (10, 18) SHUFFLE qs (9, 10, 18) TIME EDIT qg (14) TIME/TEXT w; (11) X-FADE/NO DELAY wg (19, 20) Parts Identification Front Panel The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for details. Rear Panel 2ND CD IN jacks 3 (8) ANALOG OUT L/R jacks 4 (6) CONTROL A1II jacks 1 (6, 20) DIGITAL OUT OPTICAL jack 2 (7) Mains lead 5 (6) BUTTON DESCRIPTIONS A OPEN/CLOSE wj (7, 9, 10, 11) H 5 (9, 13, 15, 18, 20, 22) X 6 (10, 15, 18, 22) x 7 (10, 15, 18) lAMSL (DISC) dial qa (10, 13, 15, 17, 18, 19) m/M (AMS+/) wd (10, 14, 17, 18) 7 CDP-CE575 Parts Identification 5 Remote Control ANALOG OUT LEVEL +/ wh (6, 7, 10) CD1/2/3 switch 1 (7) CHECK 9 (13) CLEAR ws (13, 14, 16, 17) CONTINUE 3 (9, 13, 15, 18) DISC/CAPS 6 (10, 17) DISC SKIP +/ qh (9, 12, 13) ENTER wa (17) FADER/DEL w; (14, 20) HIGH-LIGHT wd (12) MEGA CONTROL 4 (18, 19) MUSIC SCAN qa (10) NAME INPUT qs (17) NO DELAY ql (19, 20) Number buttons 7 (10, 13, 17) PROGRAM qj (9, 13, 18) REPEAT 0 (10, 18) SHUFFLE 2 (9, 10, 18) TIME/TEXT/SPACE 5 (11, 17) X-FADE qk (19, 20) BUTTON DESCRIPTIONS 10 8 (10, 13) N wf (9, 13, 15, 18, 20, 22) X qd (10, 15, 18, 22) x wg (10, 15, 18) ./ qf (10, 13, 15, 17, 18, 19) m/M qg (10, 14, 17, 18) CDP-CE575 8 This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISASSEMBLY 3-2. CASE (409538) (Page 9) 3-3. FRONT PANEL SECTION (Page 9) 3-6. BASE UNIT (BU-5BD27) (Page 11) 3-7. TABLE ASSY (Page 11) 3-5. MAIN BOARD (Page 10) 3-4. CD MECHANISM DECK (CDM59-5BD27) (Page 10) 3-8. SENSOR BOARD (Page 12) 3-9. LOADING MOTOR BOARD (Page 12) SET CDP-CE575 9 3-2.CASE (409538) 3-3.FRONT PANEL SECTION 1two screws (case3 TP2) 3case (409538) 2two screws (BVTP3 8) 1two screws (case3 TP2) 2connector (CN601) 2connector (CN602) 4claw 3four screws (BVTP3 8) 5front panel section 4claw 1wire (flat type) (15 core) (CN801) 2connectors (CN351) CDP-CE575 10 3three screws (BVTP3 8) 2three screws (BVTP3 8) 7wire (flat type) (21 core) (CN301) 8connector (CN311) 5screw (BVTP3 8) 4Slide the tray until the screw that fixes the table assy can be seen through around hole in the table assy. 1Insert a tapering driver from the bottom of the chassis, and turn it in the direction of the arrow until the base unit goes down to the lowest position. 6 9CD mechanism deck (CDM59-5BD27) a a 3-4.CD MECHANISM DECK (CDM59-5BD27) 3-5.MAIN BOARD 3 two screws (PTTWH3 6) 2 two screws (BVTP3 8) 5 MAIN board1 three screws (BVTP3 8) 4 two PC board holders CDP-CE575 11 4two screws (PTPWH M2.6) 4two screws (PTPWH M2.6) 5base unit (BU-5BD27) 1wire (flat type) (21 core) (CN101) 6four compression springs (932) 3 2two screws (PTPWH M2.6) 7holder (BU) assy lever (lifter) BU section Note: When installing the BU on the chassis, set the lever (lifter) in free position, the gear (U/D) in UP position, and insert the shaft into the groove of gear (U/D). gear (U/D) b b 3-6.BASE UNIT (BU-5BD27) 3-7.TABLE ASSY Note: When installing the table assy on the chassis assy, engage the gear (loading C) with the groove by looking into the gear through a hole in the table assy. qstable assy 9three screws (BTTP M2.6) q;clamp e c c d d e qabracket (guide) gear (loading C) 7two screws (BTTP M2.6) 5screw (BTTP M2.6) 6bracket (guide)2two screws (BTTP M2.6) 1Slide the tray until the screw that fixes the bracket (guide) can be seen through a round hole , in the table assy. 3 8bracket (guide 2) 4wire (flat type) (6 core) (CN15) CDP-CE575 12 3-8.SENSOR BOARD 3-9.LOADING MOTOR BOARD 3 two screws (BTTP M2.6) 4 LOADING MOTOR board 1 belt (loading) 2 connector (CN13) 1 screw (PTPWH M2.6) 3 belt (rotary) 4 two screws (BTTP M2.6) 4 two screws (BTTP M2.6) 5 SENSOR board 2 tray CDP-CE575 13 SECTION 4 ASSEMBLY Note: Follow the assembly procedure in the numerical order given. ADJUSTING PHASE OF SWING GEAR AND GEAR (U/D) 6 screw (PTPWH M2.6) 5 stopper washer (FR) 4 Push fully the shaft of shaft gear and align the hole shape of gear (loading B). 3 Let the swing gear through under the chassis and engage its dowel with the groove of rotary encoder. 2 Install the rotary encoder so that its groove comes to the position shown in the figure. 1 Insert the shaft gear up to the position where its shaft comes out by 5 mm. g g h h f f f 7 gear (U/D) 8 screw (PTPWH M2.6) q; screw (PTPWH M2.6) circle mark circle mark swing gear gear (RV) Fig. A 9 gear (RV) Note: Align swing gear, a circle mark on the gear (U/D), and the teeth of gear (RV) to the position showing in the Fig. A. 14 CDP-CE575 ADJ MODE NOTE: This mode cannot be performed without a general remote com- mander. 1.Chuck the CD first, and then turn OFF the power. 2.Short-circuit the test point TP (ADJ) of the MAIN board and ground with a lead wire. 3.Press the POWER button to turn ON the power. The CD is playback the 2nd track automatically and the ADJ mode is set. 4.To exit the mode, press the POWER button to turn OFF the power. ADJ Mode Special Function Table ButtonFunction DISC 1RFDC display DISC 2Decision of Disc size (8/