Philips-HTS-5200-Service-Manual电路原理图.pdf

1 - 1HTS5200/12/98/51©Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The NetherlandsAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system ortransmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwisewithout the prior permission of Philips.Published by RY1014 Service Audio Printed in The Netherlands Subject to modificationDVD Home Theater SystemVersion 1.1TABLE OF CONTENTSLocation of PCB Boards . 1-2Versions Variation . 1-2Measurement Setup . 1-4Specifications . 1-3Service Aids . 1-5ESD & Safety Instruction . 1-6Lead-free soldering Information . 1-7Setting procedure & Repair Instructions. 2Disassembly Instructions & Service positions . 3Block & Wiring Diagram . 4VFD+USB+AUX Board . 5Main+LED Board. 6Power Board . 7Service ManualServiceTfswjdfServiceTfswjdfServiceAMP Board . 8Touch Board . 9Mechanical Exploded view . 10Revision List . 11GBChapter3139 785 353011 - 2LOCATION OF PCB BOARDSVERSION VARIATION:Type/VersionsFeatures HTS5200Output Power - 400WVoltage (110127V)Voltage (220240V)Main+Led BoardVFD+USB+UAX BoardAMP BoardType/VersionsBoard in usedHTS5200CCC/12REPAIR SCENARIO MATRIX:/12xx*C = Component Level RepairPower BoardCTouch BoardCCCC/98CC/98xxxTOUCH PCBVFD PCBMAIN PCBPOWER PCBDOOR LED PCBLED PCBMAIN PCBAUX PCBAMPPCBPOWER PCBUSB PCBTOP VIEW BOTTOM VIEW/51xxCCC/51CC1 - 3SPECIFICATIONSPlayback mediaDVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R DL,CD-R/CD-RW, Audio CD, Video CD/SVCD, Picture CD, MP3-CD, WMA-CD, DivX-CD, USB storage device (for /12/98)AVCHD, BD-RE, BD-Video, DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-RDL, CD-R/CD-RW, Audio CD, Video CD/SVCD, Picture CD, MP3-CD, WMA-CD, DivX (Ultra)-CD, USB storage device (for /51)File FormatAudio . .mp3, .wma (for /12/98)Audio . .mp3, .wma.wav (for /51)Video . .divx, .divx ultra, .mpeg, .mpg, .wmv (simple profi le).(for /12/98)Video . .avi, .divx, .mp4, .mkv, .mov, .wmv (for /51)Picture . .jpeg, .jpg (for /12/98)Picture . .jpg, .gif, .png (for /51)AmplifierTotal output power . 400 W RMS (for /12/98)Total output power . 1000 W RMS (30%THD) (for /51)Frequency response . 20 Hz-20 kHz / ±3dBSignal-to-noise ratio . > 65 dB (CCIR) / (A-weighted)Input sensitivity .AUX . 1000 mV (for /12/98)AUX . 900 mV (for /51)MP3 LINK . 550 mV (for /12/98)MP3 LINK . 500 mV (for /51)VideoSignal system . PAL / NTSCComponent video output . 480i/576i, 480p/576p, 720p, 1080i (for /51)HDMI output . 480i/576i, 480p/576p, 720p, 1080i, 1080p (for /12/98)HDMI output . 480i/576i, 480p/576p, 720p,1080i, 1080p, 1080p24 (for /51)AudioS/PDIF Digital audio input .Coaxial . IEC 60958-3Sampling frequency .MP3 . 32 kHz, 44.1 kHz, 48 kHzWMA . 44.1 kHz, 48 kHzConstant bit rate .MP3 . 112 kbps - 320 kbpsWMA . 48 kbps - 192 kbpsRadioTuning range . FM 87.5-108 MHz (50 kHz) (for /12)Tuning range . FM 87.5-108 MHz (50/100 kHz) (for /98/51)Signal-to-noise ratio . FM 50 dBFrequency respose . FM 180 Hz12.5 kHz / ±3dBUSBCompatibility . Hi-Speed USB (2.0)Class support . UMS (USB Mass Storage Class)File system . FAT16, FAT32Maximum memory support . ,the home theater will start to upgrading automaticallyNote: when upgrade in progress, please do not unplug or switch off the device.when the updated is complete ,the home theater automatically switch to standby. 7) Produce to change Tuner grid (for /98) Only applicable for certain regions, in some countries, the frequency step between adjancent channels in the FM hand is 50KHZ(100KHZ in some areas)a) Press on R/C to select “FM”b) In “FM” playbak mode,press & hold button until “grid 9” or “grid 10” appearsNote: repeaing the same action will toggle back to it previous tunning grid setting.* “grid 10” is default for /55/98 version.8)How to replace the defective DVD Loadera) Remove the defective DVD Loader (see chapter 3).b) Accordingly connect DVD Loader and “CN802”, “CN803”, “CN801” on the top of main board as shown below:CN802CN801CN803CAUTION! This information is confidential and may not be distributed.Only a qualified service person should reprogram the Region Code.Upgrade file detected Do you wish to continue withthe software upgrade? OK CancelCurrent model: 5200-12/98/51Version:00.08.00_1 Release:2009.12.16Region: 2 Servo:D1.72.01.008032: 05.00.04.06 Risc: BB.00.00.00MCU: 06.01 Touch: 0044 Dock: Errorif current model doesnot match your set,use down arrow key on the remote to change OKc) Remove solder joint on the ESD protection point.The ESD protection point on the top side view of OPU The Top side view of OPU Note: The ESD protection point on any one side must be soldered if - the DVD Loader is OK and needs to be disconnected from connector CN802, CN803 and CN801 of the main board. - the defective DVD Loader is needed to be send back to supplier for failure analysis and to support back charging evidence.1)Restore factory settinga) Press button on R/Cb) Select ,then press c) Select ,then press to confirm2)Region code change a) Open the Door,then,press “1” “5” “9” on RCb) Press button on RCc) TV will show message as follow:d) If current model doesnot match your set, use down arrow key on the remote to change.3)Password change a) Press button on R/Cb) Select ,then press c) Select ,then press to confirm“0000” is default password supplied.4)Trade modela) Press button on R/Cb) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA OFF“5)Check on software versiona) Press button on R/Cb) Select ,then press c) Select ,then press d) TV will show message as follow: Preference setup Version Info.Current model: 5200-12/98/51 Version :00.08.00_1 Release: 2009.12.16Region: 2 Servo: D1 .72.01.00 8032:05.00.04.06 Resc: BB.00.00.00 MCU: 06.01 Touch: 0044OK Press SETUPto exit menu2 - 22 - 2REPAIR INSTRUCTIONS (One)2 - 32 - 3REPAIR INSTRUCTIONS (Two)