Philips-HTS-3610-K-Service-Manual电路原理图.pdf

Published by KC-TE 0519 AV Systems Printed in the Netherlands Subject to modication EN 3139 785 31630HTS3300K/51 für Reparaturen sind Original-Ersatzteile zu verwenden.Sicherheitsbauteile sind durch das Symbol !markiert.ILe norme di sicurezza esigono che lapparecchio venga rimessonelle condizioni originali e che siano utilizzati i pezzi di ricambioidentici a quelli specificati.Componenty di sicurezza sono marcati con !GBAfter servicing and before returning set to customer perform a leakagecurrent measurement test from all exposed metal parts to earth ground toassure no shock hazard exist. The leakage current must not exceed0.5mA.EN 73139 785 31630Measurements Setup, Service Aid & Lead Free Requirements 2.2.1 Lead Free RequirementsPb(Lead) Free SolderWhen soldering , be sure to use the pb free solder.INDENTIFICATION:Regardless of special logo (not always indicated) one must treat all sets from 1 Jan 2005 onwards, according next rules:Important note: In fact also products of year 2004 must be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this.Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400°C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. Adjust your solder tool so that a temperature around 360°C 380°C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400°C otherwise wear-out of tips will rise drastically and fl ux-fl uid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid or does not know whether product is lead-free, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs:- always use the 12nc-recognizable soldering temperature profi le of the specifi c BGA (for de-soldering always use the lead-free temperature profi le, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYS-website.Do not re-use BGAs at all. For sets produced before 1.1.2005 (except products of 2004), containing leaded solder-alloy and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website www.atyourservice.ce.Philips.com you fi nd more information to: null BGA-de-/soldering (+ baking instructions)null Heating-profi les of BGAs and other ICs used in Philips-setsYou will fi nd this and more technical information within the “magazine”, chapter “workshop news”.For additional questions please contact your local repair-helpdesk.EN 8 3139 785 316303. Directions For Use3. Directions For UseThe following except of the Quick Use Guide serves as an introduction to the set.The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: www.p4c.philips.comQUICK START GUIDE 12nc: 3139 246 19201HTS3300K1 whats in the box 2 connect TV3 connect subwoofer, speakers and antennas3a Placement of speakers3c Connect theFM and MWantennasREAR L REAR RFRONT LCENTERFRONT RSubwooferTV3b Connect the speakersand subwoofer to theDVD system(refer to the user manual for“Individual speaker volumeadjustment”)3d Connect the mainscord to the powersupplyPbPr YLRFRONT RFRONT LREAR RREAR LCENTERNote:For connecting to a Progressive Scan TV,refer to the user manual for properconnections and detailed set up.ARemote controlincludes 2x AA batteriesDBGHCSubwooferFM wireantennaMW loop antennaMain unitFront/Rear/Center speakersVideo cableE Audio cableFAHGEAY Pb Pr cablesnot suppliedOREN 93139 785 31630Directions For Use 3.4 play a discDISC4a Press DISC.Point the remote controltowards the DVD system.4b Load in a discPress OPEN CLOSE toopen and close the disctray.4c Select correctAV In channelSwitch to the correctinput source by using theTV remote control.GET PICTURE Check the connection of the DVD systemto TV is in place (see 2 Connect TV). Check the AV mode on TV. It may becalled FRONT, A/V IN, or VIDEO. Choosethe different modes using TV remotecontrol. Or, use the TV remote control to selectChannel 1 on TV, then press Channel downbutton until you get the picture. See your TV manual for more details.Refer to chapter “DVD Setup Menu Options” in the user manualfor detailed descriptions.More settings and features GET SOUNDTo enhance the soundqualityPress SOUND button toselect a predefined digitalsound effect.Detailed playback features and additionalfunctions are described in the user manual.No sound from rearspeakers?Press SURR button to select“Multi-Channel”.5 programme radio stationsNEEDS HELP? Visit our website www.philips.com/support5a Press TUNER.5b Press and hold PLAY 2until“START .” appears.It will start to programmeall available radio stations.5c Once complete, useS / T to select apreset radio station.Note: This feature is only availablefor first time setup.6 connect other device (optional)AUDIO OUTPbPr YLRAudio/Video deviceNote: Connect the AUDIO OUTPUT of other audio/videodevice to this DVD system in order to use the HomeTheatre Audio Systems surround sound capabilities.Press AUX/DI on the remote control in order tolisten to the playback.EN 10 3139 785 316303. Directions For UseQuickStartGuideHTS3610KHomeTheatreSystemDVDsystemRearspeakers(left&right)Remotecontroland2batteriesQuickstartguideCentrespeakerSubwooferFrontspeakers(left&right)WhatsintheBoxAudiocables(red&whiteplugs)Videocables(yellowplug)AM/MWloopantennaFMwireantennaUsermanualConnectSpeakers&SubwoofertoDVDSystemConnectthevariouscolouredplugsfromthespeakersandsubwoofertothesamecoloursocketontherearofDVDsystem.FixAntennas1ConnecttheFMantennatotheFMsocket,extendtheantennaandfixitonthewall.DVDSystem(back)2UnfoldtheAM/MWloopantennaandfixtheclawintotheslot.3Pushbacktabandinserteachwireintoslot.PositionSpeakers&Subwoofer1PlacecentrespeakeronorclosetotheTV.2Placesubwooferonthefloor.3PlacefrontspeakersequaldistancefromtheTVandanglethem45degreetothelistener.4Placerearspeakersfacingthelistener,equaldistanceontheleftandright.MWloopantennaDVDSystem(back)RearSpeaker(left)RearSpeaker(right)FrontSpeaker(right)FrontSpeaker(left)CentreSpeakerDVDSystem(back)Sub-Woofer