Philips-DVP-5996-K-Service-Manual电路原理图.pdf

· Instruction.2-1 · Software Upgrade.3-1 · Accessory list.4-1 · Revision List.5-1 This simple Service Manual is for “ Exchange“ Scenario TABLE OF CONTENTS Page 3139 785 33404 Version 1.4 DVP3260 DVP3264 DVP3252 DVP5990 DVP3266K DVP5996KService Manual PHILIPS GB ©Copyright 2008 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. CLASS 1 LASER PRODUCTPublished by KC-ET 0809 Service Audio Printed in The Netherlands Subject to modification DVP3260/05/12 DVP3260/05(Second Generation)DVP3264/12 DVP3260/12(Second Generation)DVP3252/51/75 DVP3264/12(Second Generation)DVP5990/12/05 DVP3266K/51 DVP5996K/51 Service DVD Player How to remove the CD manually from the tray 1. Please do as below instruction in case the tray can not be open: I. Power off the DVD player. II. Please gently push the guider and wait until the tray comes out (Figure1). 2-1 Figure 1 Software upgrade Preparation to upgrade software 1) Start the CD Burning software and create a new CD project (Data Disc) with the following setting: Label: DVPXXXX (No need the label name) File Name: DVPXXXX_XX.BIN Power on the set and open the tray, then press to check the File Name. Note: It is required capital letter for the File System name 2) Burn the data onto a blank CDR A. Procedure for software upgrade: 1) Power on the set and insert the prepared Upgrade CDR. 2) The set will starts reading disc & response with the following display TV screen: Upgrade File DETECTED Upgrade? Press Play TO START. 3) Press button to confirm, then screen will display : Files coping UPGRADING 4) The upgraded disc will automatically out when files coping complete, then take out the disc. 5) About 1 minute later, the trace will automatically close when upgrading complete. B. Read out the software versions to confirm upgrading 1) Power on the set and press button on the remote control. 2) Pressbutton to check the software information. The software version and other information are display on the TV screen as follows: Version XX.XX.XX.XX (Main version) SUB-VER XX.XX.XX.XX (software version of application software) 8032 XX.XX.XX.XX Servo XX.XX.XX.XX (software version of Servo) RISC XX.XX.XX.XX DSP XX.XX.XX.XX Region Code X 3-1 Caution: The set must not be power off during upgrading, Otherwise the Main board will be damaged entirely. Item No. 12NC No. Description RC 996510010908 Remote control for DVP3260/05/12, DVP3264/12, DVP3260/05/12(Second Generation) and DVP3264/12 (Second Generation) 996510012682 Remote control for DVP5990/12/05 996510010908 Remote control for DVP3252/51 and DVP3252/75 996510010959 Remote control for DVP3266K/51 996510013355 Remote control for DVP5996K/51 AV Cable 996510001106 AV Cable for DVP5990/05/12, DVP3252/51 , DVP3266K/51, DVP5996K/51 and DVP3252/75 Accessories Spare Parts List 4-1 5-1 Revision List Version 1.0 Initial Release Version 1.1 * Adding DVP3252/51 * Adding DVP5990/12/05 * Update Accessory Spare Part List Version 1.2 * Adding DVP3266K/51 * Update Accessory Spare Part List Version 1.3 * Adding DVP5996K/51 * Adding DVP3252/75 * Update Accessory Spare Part List Version 1.4 * Adding DVP3260/05 (Second Generation, OPU type: IM) * Adding DVP3260/12 (Second Generation, OPU type: IM) * Adding DVP3264/12 (Second Generation, OPU type: IM)