Philips-DVP-3388-K-Service-Manual电路原理图.pdf

TABLE OF CONTENTS Page Version 1.0 Service Manual . Technical Specifications.1-2 . Safety Instruction, Warning 525 (NTSC/60Hz) Playback: Multi-standard (PAL/NTSC) Video performance Video DAC: 12 bits, 108 MHz Y Pb Pr: 0.7 Vpp 75 ohm Video output: 1 Vpp 75 ohm Video format Digital compression: MPEG 2: DVD/SVCD MPEG 1: VCD/DivX Horizontal resolution: DVD: 720/1920 pixels (50 Hz); 720/1920 pixels (60 Hz) VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) Vertical resolution: DVD: 576/1080 lines (50 Hz); 480/1080 lines (60 Hz) VCD: 288 lines (50 Hz); 240 lines (60 Hz) Audio performance DA converter: 24 bits, 192 kHz Frequency response: DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz - 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz) Signal-Noise (1 kHz): > 90 dB (A-weighted) Dynamic range (1 kHz): > 80 dB (A-weighted) Crosstalk (1 kHz): > 70 dB Distortion/noise (1 kHz): > 65 dB MPEG MP3: MPEG Audio L3 Audio format Digital: MPEG/AC-3/PCM: Compressed digital (16, 20, 24 bits fs, 44.1, 48, 96 kHz) MP3 (ISO 9660): 96, 112, 128, 256 kbps IEC61937 for MPEG 1/2, Dolby Digital 1 optical HDMI output 5.1 channel analog output Audio Front L+R: Cinch (white/red) Audio Rear L+R: Cinch (white/red) Audio Center: Cinch (blue) Audio Subwoofer: Cinch (black) 1-2 For DVP3386K/93 Note Speci cation and design are subject to change without notice. Accessories supplied Quick Start Guide Remote control and batteries Audio/video cables Power cable (except for Taiwan) Playback media DVD-Video, Video CD/SVCD, Audio CD, CD-R/ CD-RW, DVD+R/+RW, DVD-R/-RW, DivX-CD, Picture CD, MP3-CD, WMA-CD, WMV-CD, USB ash drive USB Compatibility: Hi-Speed USB (2.0) Class support: UMS (USB Mass Storage Class) TV standard Number of lines: 625 (PAL/50Hz); 525 (NTSC/60Hz) Playback: Multi-standard (PAL/NTSC) Video performance Video DAC: 12 bits, 108 MHz Y Pb Pr: 0.7 Vpp 75 ohm Video output: 1 Vpp 75 ohm Video format Digital compression: MPEG 2: DVD/SVCD MPEG 1: VCD/DivX Horizontal resolution: DVD: 720/1920 pixels (50 Hz); 720/1920 pixels (60 Hz) VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) Vertical resolution: DVD: 576/1080 lines (50 Hz); 480/1080 lines (60 Hz) VCD: 288 lines (50 Hz); 240 lines (60 Hz) Audio performance DA converter: 24 bits, 192 kHz Frequency response: DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz - 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz) Signal-Noise (1 kHz): > 90 dB (A-weighted) Dynamic range (1 kHz): > 80 dB (A-weighted) Crosstalk (1 kHz): > 70 dB Distortion/noise (1 kHz): > 65 dB MPEG MP3: MPEG Audio L3 Audio format Digital: MPEG/AC-3/PCM: Compressed digital (16, 20, 24 bits fs, 44.1, 48, 96 kHz) MP3 (ISO 9660): 96, 112, 128, 256 kbps IEC61937 for MPEG 1/2, Dolby Digital 1 optical HDMI output 5.1 channel analog output Audio Front L+R: Cinch (white/red) Audio Rear L+R: Cinch (white/red) Audio Center: Cinch (blue) Audio Subwoofer: Cinch (black) Specification For DVP3388K/98 & DVP3388K/96 1-2Safety instruction 1. General safety Safety regulations require that during a repair: . Connect the unit to the mains via an isolation transformer. . Replace safety components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical DC resistance between the mains plug and the secondary side: 1) Unplug the mains cord, and connect a wire between the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4) Repair or correct unit when the resistance measurement is less than 1M . 5) Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury). Laser device unit T ype : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 degree Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning & Notes 1-3Warning 1.General . All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handing during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: 1) Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester 4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , including the heat sink, carries live mains voltage when you connect the player to the mains (even when the player is “off”!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A “lighting stroke” and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while the unit is “on”. 2. Laser . The use of optical instruments with this product, will increase eye hazard. . Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury. . Repair handing should take place as much as possible with a disc loaded inside the player. . Text below is placed inside the unit, on the laser cover shield: Notes: Manufactured under licence from Dolby Laboratories. The double-D symbol is trademarks of Dolby Laboratories, Inc. All rights reserved. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO BEAM. 1-4Lead-Free requirement for service INDENTIFICATION: Regardless of special logo (not always indicated) One must treat all sets from 1.1.2005 onwards, according next rules. Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400°C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. Adjust your solder tool so that a temperature around 360°C 380°C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400°C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: - always use the 12nc-recognizable soldering temperature profile of the specific BGA (for de-soldering always use highest lead-free temperature profile, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website: www.atyourservice.ce.Philips.com You find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will find this and more technical information within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. Notes 1-52009 © Koninklijke Philips N.V. All rights reserved. 12 NC 8670 000 48883 sgptt_909/93 Register your product and get support at www.philips.com/welcome DVP3386K CD 3 / The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages from Philips Customer Contact & Support site: www.p4c.philips.com 2-12009 © Koninklijke Philips N.V. All rights reserved. 12 NC 8670 000 48884 sgptt_910/98 Register your product and get support at www.philips.com/welcome DVP3388K Off On Audio Sync Volume Digital Audio Analog Output HDMI Audio Audio Setup Sound Mode Speaker Setup CD Upsampling 3 / 2-1 The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages from Philips Customer Contact & Support site: www.p4c.philips.com2009 © Koninklijke Philips N.V. All rights reserved. 12 NC 8670 000 51951 sgptt_910/96 Register your product and get support at www.philips.com/welcome DVP3388K Off On Audio Sync Volume Digital Audio Analog Output HDMI Audio Audio Setup Sound Mode Speaker Setup CD Upsampling 3 / 2-1 The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages from Philips Customer Contact & Support site: www.p4c.philips.com1 DIVX(R) 2 HDMI IN HDMI OUT AUDIO OUT FRONT L/R & TV OUT COMPONENT VIDEO IN Pb Y Pr YPbPr & AUDIO OUT FRONT L/R 2-2Product overview Main unit a2 (Standby-on) Turn on the DVD player or switch to standby mode. b Disc compartment c Display panel d Z (Open/Close) Open or close the disc compartment. e u (Play/Pause) Start, pause or resume disc play. f (USB) jack Connect a USB ash drive. g MIC Audio input from a microphone. 4 3 1 2 6 5 7 Remote control 4 3 6 7 9 8 1 5 2 16 17 12 15 13 14 10 11 18 a2 (Standby-On) Turn on the DVD player or switch to standby mode. Press and hold to turn off the DVD player and all HDMI CEC compliant devices. b Z (Open/Close) Open or close the disc compartment. c DISC MENU Access or exit the disc menu. Switch to disc mode. For VCD/SVCD, turn PBC (Playback Control) on or off in PBC mode. 2-3