Philips-HTR-5204-Service-Manual电路原理图.pdf
HTR5204/1271-21-21-31-41-51-61-7234567Digital A/V Surround Receiver8Control 50 HzPower Consumption: 100 WStandby Power Consumption: < 1 WDimensions: 435 x 56 x 325 mm(w x h x d)Weight: 3.2kgCENTRE SPEAKERSystem Full range satelliteImpedance: 8 Speaker drivers: 2 x 2.5” woofer, 1 x 2” tweeterFrequency response: 150Hz 20 kHz Dimensions: 435 x 93.5 x 67 mm(w x h x d)Weight: 1.28 kg PASSIVE SUBWOOFERFrequency response: 40 Hz 150 HzImpedance: 8 Subwoofer driver: 8” subwoofer,Dimensions: 159.5 x 355.5 x 370 mm(w x h x d)Weight: 4.712kgSpecifications subject to change without prior notice.FRONT AND REAR SPEAKERSSystem Full range satelliteImpedance: 4 Speaker drivers: 3” fullrange speakerFrequency response: 150 Hz 20 kHz Dimensions: 95.6 x 198.3 x 75 mm(w x h x d)Weight: 0.62 kg /eachMeasurement SetupTuner AM (MW,LW)Tuner FMBandpassBandpass1-4Service Tools:Universal Torx driver holder .4822 395 91019Torx bit T10 150mm .4822 395 50456Torx driver set T6-T20 .4822 395 50145Torx driver T10 extended .4822 395 50423Compact Disc:SBC426/426A Test disc 5 + 5A .4822 397 30096SBC442 Audio Burn-in test disc 1kHz .4822 397 30155SBC429 Audio Signals disc .4822 397 30184Dolby Pro-logic Test Disc .4822 395 10216SERVICE AIDSHANDLING CHIP COMPONENTS1-5NL WAARSCHUWINGAlle ICs en vele andere halfgeleiders zijngevoelig voor electrostatische ontladingen(ESD).Onzorgvuldig behandelen tijdens reparatie kande levensduur drastisch doen verminderen.Zorg ervoor dat u tijdens reparatie via eenpolsband met weerstand verbonden bent methetzelfde potentiaal als de massa van hetapparaat.Houd componenten en hulpmiddelen ook opditzelfde potentiaal.I AVVERTIMENTOTutti IC e parecchi semi-conduttori sonosensibili alle scariche statiche (ESD).La loro longevità potrebbe essere fortementeridatta in caso di non osservazione della piùgrande cauzione alla loro manipolazione.Durante le riparazioni occorre quindi esserecollegato allo stesso potenziale che quello dellamassa dellapparecchio tramite un braccialettoa resistenza.Assicurarsi che i componenti e anche gli utensilicon quali si lavora siano anche a questopotenziale.GBSafety regulations require that the set be restored to its originalcondition and that parts which are identical with those specified,be used.Safety components are marked by the symbol ! .NLVeiligheidsbepalingen vereisen, dat het apparaat bij reparatie inzijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,identiek aan de gespecificeerde, worden toegepast.De Veiligheidsonderdelen zijn aangeduid met het symbol ! .FLes normes de sécurité exigent que lappareil soit remis à létatdorigine et que soient utiliséés les piéces de rechange identiquesà celles spécifiées.Less composants de sécurité sont marqués ! .DBei jeder Reparatur sind die geltenden Sicherheitsvorschriften zubeachten. Der Original zustand des Geräts darf nicht verändert werden;für Reparaturen sind Original-Ersatzteile zu verwenden.Sicherheitsbauteile sind durch das Symbol ! markiert.ILe norme di sicurezza esigono che lapparecchio venga rimessonelle condizioni originali e che siano utilizzati i pezzi di ricambioidentici a quelli specificati.Componenty di sicurezza sono marcati con ! .GBAfter servicing and before returning set to customer perform a leakagecurrent measurement test from all exposed metal parts to earth groundto assure no shock hazard exist, The leakage current must notexceed 0.5mA.CLASS 1LASER PRODUCT3122 110 03420GB Warning !Invisible laser radiation when open.Avoid direct exposure to beam.S Varning !Osynlig laserstrålning när apparaten är öppnad och spärrenär urkopplad. Betrakta ej strålen.SF Varoitus !Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiinanäkymättömälle laserisäteilylle. Älä katso säteeseen!GB WARNINGAll ICs and many other semi-conductors aresusceptible to electrostatic discharges (ESD).Careless handling during repair can reduce lifedrastically.When repairing, make sure that you areconnected with the same potential as the massof the set via a wrist wrap with resistance.Keep components and tools also at thispotential.F ATTENTIONTous les IC et beaucoup dautressemi-conducteurs sont sensibles auxdécharges statiques (ESD).Leur longévité pourrait être considérablementécourtée par le fait quaucune précaution nestprise à leur manipulation.Lors de réparations, sassurer de bien être reliéau même potentiel que la masse de lappareil etenfiler le bracelet serti dune résistance desécurité.Veiller à ce que les composants ainsi que lesoutils que lon utilise soient également à cepotentiel.ESDD WARNUNGAlle ICs und viele andere Halbleiter sindempfindlich gegenüber elektrostatischenEntladungen (ESD).Unsorgfältige Behandlung im Reparaturfall kandie Lebensdauer drastisch reduzieren.Veranlassen Sie, dass Sie im Reparaturfall überein Pulsarmband mit Widerstand verbundensind mit dem gleichen Potential wie die Massedes Gerätes.Bauteile und Hilfsmittel auch auf dieses gleichePotential halten.DK Advarse !Usynlig laserstråling ved åbning når sikkerhedsafbrydere erude af funktion. Undgå udsaettelse for stråling.F“Pour votre sécurité, ces documents doivent être utilisés pardes spécialistes agréés, seuls habilités à réparer votreappareil en panne“.GB ESD PROTECTION EQUIPMENTComplete Kit ESD3 (small tablemat, wristband,connection box, estention cable and earth cable . 4822 310 10671Wristband tester . 4822 344 139991-6Pb(Lead) Free SolderWhen soldering , be sure to use the pb free solder.INDENTIFICATION:Regardless of special logo (not always indicated)one must treat all sets from 1 Jan 2005onwards, accordingnext rules:Important note: In fact also products of year 2004 mustbe treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305and the higher temperatures belong to this.Due to lead-free technology some rules have to berespected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 withorder code 0622 149 00106. If lead-free solder-pasteis required, please contact the manufacturer of yoursolder-equipment. In general use of solder-pastewithin workshops should be avoided because paste isnot easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able To reach at least a solder-temperature of 400?C, To stabilize the adjusted temperature at the solder-tip To exchange solder-tips for different applications. Adjust your solder tool so that a temperature around360?C 380?C is reached and stabilized at the solderjoint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400?C otherwisewear-out of tips will rise drastically and flux-fluid willbe destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solderalloy / parts is possible but PHILIPS recommendsstrongly to avoid mixed solder alloy types (leaded andlead-free).If one cannot avoid or does not know whether productis lead-free, clean carefully the solder-joint from oldsolder alloy and re-solder with new solder alloy(SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities)has to be purchased at external companies. Special information for BGA-ICs: Always use the 12nc-recognizable solderingtemperature profile of the specific BGA (for de-soldering always use the lead-free temperature profile,in case of doubt) Lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) toprotect the IC against moisture. After opening,dependent of MSL-level seen on indicator-label in thebag, the BGA-IC possibly still has to be baked dry.(MSL=Moisture Sensitivity Level). This will becommunicated via AYS-website.Do not re-use BGAs at all. For sets produced before 1.1.2005 (except productsof 2004), containing leaded solder-alloy andcomponents, all needed spare-parts will be availabletill the end of the service-period. For repair of suchsets nothing changes. On our website www.atyourservice.ce.Philips.comyou find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used inPhilips-setsYou will find this and more technical informationwithin the “magazine”, chapter “workshop news”.For additional questions please contact your localrepair-helpdesk.1-72 - 12 - 1System , Region Code , etc. Setting Produre1)System Reseta) switch source to DISC 6CHb) press and hold buttom on front panelc) VFD will display reset, then sysytem power down and return to original default setting2)Version & Region Code Changea) switch source to DISC 6CHb) press”9” “1“ “0“ on R/Cc) press volume + / - key on R/C to choose desired one 5 regions: EU 12 / UK 05 / APAC 98 / US 37 / US 983)Check on the Sofeware Versiona) switch source to DISC 6CHb) press “1“ “5“ “9“ buttom on R/C c) VFD will display the version6)Upgrading new sofewarea) copy file HTR5200.ROM to root directory of USB discb) switch source to 6CHc) insert USB disc to HTR520X USB socketd) VFD will display UPGRADENOTE: during software upgrade ,you must not press any key and power down. After software upgrading completed ,move USB will display on VFD ,now ,you must power down.CAUTION !Thisinformationisconncialand may notbedistributed.Onlya quadservicepersonshouldreprogramtheRegionCode.2 - 22 - 2REPAIR INSTRUCTION2 - 32 - 3REPAIR INSTRUCTION
