Philips-FWC-100-Service-Manual电路原理图.pdf

CLASS 1LASER PRODUCTCOMPACTDIGITAL AUDIOService ManualServiceServiceServiceSPR 00 0001FW-C100/21/21M/22/30/34/37TABLE OF CONTENTSPageLocation of pc boards für Reparaturen sind Original-Ersatzteile zu verwenden.ILe norme di sicurezza esigono che lapparecchio venga rimessonelle condizioni originali e che siano utilizzati i pezzi di ricambioidentici a quelli specificati.“After servicing and before returning set to customer perform aleakage current measurement test from all exposed metal parts toearth ground to assure no shock hazard exist. The leakage currentmust not exceed 0.5mA.“CLASS 1LASER PRODUCT3122 110 03420GB Warning !Invisible laser radiation when open.Avoid direct exposure to beam.S Varning !Osynlig laserstrålning när apparaten är öppnad och spärrenär urkopplad. Betrakta ej strålen.SF Varoitus !Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiinanäkymättömälle laserisäteilylle. Älä katso säteeseen!DK Advarse !Usynlig laserstråling ved åbning når sikkerhedsafbrydere erude af funktion. Undgå udsaettelse for stråling.1-6PCS 90 1152-1SPR 00 00043DIGITAL SOUND CONTROLSTANDBY-ONPROGRAM CLOCKTIMERFULL AUTO STOPMASTER VOLUMETAPE2PLAYBACKPLAY/RECTAPE1PLAYSTOP. OPENPAUSERECORDPLAYSTOP. OPENPAUSEMINI HIFI SYSTEMCD1 2 3TAPE1 2TAPECDTUNERAUXPRESETTUNINGSTOPCLEARSEARCHPLAY PAUSEPREVNEXTDISC CHANGEDISC 3OPENCLOSEDC3CHANGERVIDEOOPTIMALJAZZROCKTECHNODSCDISC 2DISC 1DEMO STOP6 5 4 1 3 2 * when the system is in standby ordemonstration mode.If the PLUG and PLAY has not been installedbefore, you can access this feature by switchingon the system from the main power outlet.“AUTO INSTALL- PRESS PLAY” will bedisplayed.2PressPLAY to start installation.“INSTALL” will be displayed and followed by“TUNER” and then “AUTO“.ThePROGRAMstarts flashing.PLUG and PLAY will start searching for allradio stations on FM band and then followed byradio stations on MW and LW bandsrespectively.All available radio stations with sufficient signalstrength will be stored.Up to 40 presets may bestored. The last preset radio station will appear onthe display when PLUG and PLAY is completed.Toexit without storing the PLUG and PLAY,pressÇbutton(on the system only).Notes: PLUG and PLAY will be reinitiated again duringthe next power up if :i)PLUG and PLAY installation was notcompleted.ii)No stereo frequency being detected duringPLUG and PLAY, “CHECK ANTENNA“ will bedisplayed.You can store any radio stations manually orautomatically after PLUG and PLAY.When PLUG and PLAY is used,all previouslystored radio stations will be replaced.During PLUG and PLAY, if no button is pressedwithin 15 seconds, the system will go todemonstration mode (if demonstration mode isenable) Demonstration mode The system has a demonstration mode thatshows the various features offered by the system.Todisable the demonstration modePress and hold Ç(on the system only)for 5secondswhen the system is in demonstrationmode.“DEMO OFF“ is displayed.The system will switch to standby mode.2213TUNERTAPE 1/2CDSLEEPAUXDIMDSCDBBMUTEREPEATPAUSESHUFFLEÅCD DIRECTVOLUMEáàëíÉ Ç12EnglishToenable the demonstration modePress and hold Ç(on the system only)for 5secondswhen the system is in standby mode.The demonstration will begin.Notes: If the demonstration mode has not been disabled,it will resume 5 seconds later after the systemswitches to standby mode.When the system is switched on from the mainpower outlet,the CD changer tray may open andclose again to initialize the set.Even though the AC power cord is removed fromand reconnected to the wall socket,thedemonstration will remain off until it is switched onagain. Switching the system ON¶PressCD,TUNER,TAPEor AUX.¶PressSTANDBY-ON in demo.You can also switch on the system by pressingany one of the CD DIRECT PLAY buttons (onsystem only).Switching the system to standbymode¶PressSTANDBY-ONor Bon the remotecontrol. The system will switch to standby mode.Selecting the Source¶Press the respective source selection button:CD,TUNER,TAPEor AUX.The display indicates the selected source.Note: For an external source, make sure you haveconnected the audio left and right OUT terminalsof the external equipment (TV, VCR,Laser Discplayer, DVD player or CD Recorder) to the AUX INterminals.DIM mode(only on remote control)You can select the desired brightness for thedisplay.¶PressDIMto select DIM 1, DIM 2, DIM 3 orDIM OFF display mode.TheDIMdisplay lights up.“DIM 1“, “DIM 2“, “DIM 3“ or “DIM OFF“will be displayed depending on the modeselected. DIM OFF - normal brightness with VolumeIndicator On DIM 1 - normal brightness with VolumeIndicator Off DIM 2 - half brightness with VolumeIndicator On DIM 3 - half brightness with VolumeIndicator OffOperating the System