Philips-DVP-3180-K-Service-Manual电路原理图.pdf
. Technical Specifications.1-2 . Safety Instruction, Warning & Notes.1-3 . Mechanical and Dismantling Instructions.2-1 . Region Code, Software Version& Upgrades.3-1 . Trouble Shooting Chart.4-1 . Wiring Diagram.5-1 . Electrical Diagrams and Print-layouts.6-1 . Set Mechanical Exploded view .7-1 . Revision List.8-1 TABLE OF CONTENTS Page 3139 785 32430 Version 1.0 DVP3180KService ManualPHILIPS GB ©Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. CLASS 1 LASER PRODUCTPublished by TCL-H Y 701 Service Audio Printed in The Netherlands Subject to modificationDVP3180K/93 Service DVD Player Technical Specifications TV Standard (PAL/50Hz) (NTSC/60Hz) Number of lines 625 525 Playback Multi standard (PAL/NTSC) Video Performance Video DAC 10 bit, 108MHz YPbPr: 0.7Vpp 75 ohm Video output 1Vpp 75 ohm Video Format Digital Compression MPEG 2 for DVD, SVCD MPEG 1 for VCD DVD 50Hz 60Hz Horiz. resolution 720 pixels 720 pixels Vertical resolution 576lines 480 lines VCD 50Hz 60Hz Horiz. resolution 352 pixels 352 pixels Vertical resolution 288lines 240 lines Audio Format Digital MPEG/AC-3/ Compressed Digital PCM 16, 20, 24bits fs, 44.1, 48, 96kHz MP3(ISO 9660) 96,112,128,256kbps & variable bit rate fs,32, 44.1,48 kHz Analogue Sound Stereo Dolby surround-compatible downmix from Dolby Digital multi-channel sound Audio Performance DA converter 24bits, 192KHz DVD fs 96kHz 4Hz-44kHz fs 48kHz 4Hz-22kHz SVCD fs 48kHz 4Hz-22kHz fs 44.1kHz 4Hz-20kHz CD/VCD fs 44.1kHz 4Hz-20kHz Signal-Noise (1kHz) >95dB Dynamic Range (1kHz) >85dB Cross talk (1kHz) >85dB Distortion/Noise (1kHz) >75dB MPEG MP3 MPEG Audio L3 Connections YpbPr Cinch 3x Video output Cinch( yellow) Audio L+R output Cinch (white/red) Digital output 1 coaxial IEC60958 for CDDA/LPCM IEC61937 for MPEG1/2, Dolby Digital Cabinet Dimensions (w X h X d) 360 x 37 x 235 mm Weight Approximately 2.0 kg Power Consumption Power supply 110V 240V 50 / 60HZ Power consumption in standby mode to check the File Name. Note: It is required capital letter for the File System name. 2) Burn the data onto a blank CDR B. Procedure for software upgrade: 1) Power up the set and insert the prepared Upgrade CDR. 2) The set will starts reading disc & response with the following display on TV screen: SMART UPGRADE READ 3) About 2 seconds later, the TV screen will display 20 SMART UPGARD UPGRADE TO VXXX. XX. XX. 4) After 20 seconds later, the upgrading will proceed automatically, and the TV screen display as below: UPGRADING DONT POWER OFF 5) The upgraded disc will automatically out when upgrading complete, then take out the disc. 6) Power off the set and restart set. C. Read out the software versions to confirm upgrading 1) Power up the set. 2) Press button. The software version and other information are display on the TV screen as follows: XXXXXXXX (Date) VER: XX.XXX.XXX. (Version of the certification) SC: XXX (Version of the servo) F/ W ID (Version of the kernel and the software) CHIP ID (Check sum) PASSWORD REGION RATING CURRENT MODEL EXIT SETUP 3-1 Caution: The set must not be power off during upgrading, in that case the decoder board will be damaged entirely.
