欢迎来到收音机爱好者资料库! | 帮助中心 忘不了收音机那份情怀!
收音机爱好者资料库
全部分类
  • 德国收音机>
  • 国产收音机>
  • 日本收音机>
  • 国外收音机>
  • 进口随身听>
  • 卡座/开盘/组合/收录机>
  • CD/VCD/DVD/MD/DAC>
  • DAT/LP唱机>
  • 功放/音响/收扩>
  • 老电视>
  • ImageVerifierCode 换一换

    Philips-DVP-1120-Service-Manual电路原理图.pdf

    • 资源ID:83538       资源大小:1.39MB        全文页数:37页
    • 资源格式: PDF        下载积分:22积分
    会员登录下载
    三方登录下载: QQ登录
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    Philips-DVP-1120-Service-Manual电路原理图.pdf

    . Technical Specifications.1-2 . Safety Instructions, Warnings, Notes.1-3 . Mechanical and Dismantling Instructions.2-1 . Region Code, Software Version 50/60 Hz Power consumption to check the File Name. Note: It is required capital letter for the File System name. 2) Burn the data onto a blank CDR B. Procedure for software upgrade: 1) Power up the set and insert the prepared Upgrade CDR. 2) The set will starts reading disc & response with the following display TV screen: Upgrade File DETECTED Upgrade? Press Play TO START. 3) Press button to confirm, then screen will display : Files coping UPGRADING 4) The upgraded disc will automatically out when files coping complete, then take out the disc. 5) About 1 minute later, the trace will automatically close when upgrading complete. C. Read out the software versions to confirm upgrading 1) Power up the set and press button on the remote control. 2) Press button. The software version and other information are display on the TV screen as follows: Version XX.XX.XX.XX (main version) SUB-VER XX.XX.XX.XX (software version of application software) 8032 XX.XX.XX.XX Servo XX.XX.XX.XX (software version of Servo) RISC XX.XX.XX.XX DSP XX.XX.XX.XX Region Code XX 3-1 Caution: The set must not be power off during upgrading, in that case the decoder board will be damaged entirely. 4-1 Spindle motor does not move Yes Yes No No No No Yes Check whether “RFA5V” (+5V) voltage is normal. Correct connection Check the RFA5V power supply Check/Replace Q2 Q3. Check/ Replace U1. Have no focus 1. Check U1 182pin FOCUS_PWM signals 2.If there are F+, F-, T+ and T- signals output from U7. Check/Replace the loader Yes Yes No Go Check whether laser voltage (2.3V for DVD & 1.9V for CD) on Collector of Q2 and Q3 Check the FFC connection between 24P and the loader. 1.Whether voltage on pin 129 of U1 varies between 0 and 3.3V (3.3V for CD and 0V for DVD), 2.Whether peripheral components are eroded or badly soldered. Trouble shooting chart Motor no move FOCUS_PWN waveform 4-2 The power can not be on or off Go Ye s Yes No No The power cant be on or off Yes Repair the power board Check the power supply on the power board is normal. Check/Correct connection Whether the connection to K401 is broken. Correct the connection Replace U1. No No Yes Yes Check if the CN301 on the front board to CN5 on the decoder board is in good contact. Whether there is 0V and 3.3V voltage difference on Pin 192 PCON of U1. Trouble shooting chart 4-3 All output voltages on the power board is 0V or deviated.No No No Yes No U1(PIN 8 - Drain waveform) Replace F1 Replace C1&C2 if D1, D2, D3, D4 are normal. Check/ replace U1. Check whether U1 are eroded. All output voltages on the power board is 0V or deviated Check whether there is 300V on C1 and C2. Check whether 100KHz oscillating signal on Pin6 of U1 Check if +5V, , +12V and -12V are short. Check whether the components in the short-circuit voltage are defected or eroded. Yes Yes Yes Yes U1(PIN 3 - RC waveform) Trouble shooting chart Check whether F1 is blown4-4Disc cannot be read. No Yes No Yes No Yes Yes No No Yes Disc cannot be read. Check the loaded circuit 1.Check voltage on pin 100 of U1 varies between 0 and 3.3V: 3.3V for CD 0V for DVD 2.Check whether peripheral components are eroded or defect Check the FFC connection between 24P and the loader. Check U1 and peripheral components Re-solder or replace the defective parts Check the connection between U1 Correct connection Replace U1 or loader. Yes Check whether there is laser voltage (2.3V for DVD and 1.9V for CD) on Collector of Q2 &Q3 Check if there is RFO signal on pin10 of CN2. (The normal RFO signal is a clear reticulated wave) Trouble shooting chart Check U1, U7, and peripheral components are eroded or badly soldered.

    注意事项

    本文(Philips-DVP-1120-Service-Manual电路原理图.pdf)为本站会员(cc518)主动上传,收音机爱好者资料库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知收音机爱好者资料库(点击联系客服),我们立即给予删除!

    温馨提示:如果因为网速或其他原因下载失败请重新下载,重复下载不扣分。




    ADZZ
    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2025 收音机爱好者资料库 版权所有
    备案编号:鄂ICP备16009402-5号

    收起
    展开