Philips-DVDR-3460-Service-Manual电路原理图.pdf

Published by KC-TE 0715 V&MA Printed in the Netherlands Subject to modication EN 3139 785 32500DVDR3460/75/97/96DVD-Video RecorderCLASS 1LASER PRODUCTContents Page1 Technical Specications and ConnectionFacilities 22 Safety Information, General Notes & Lead Free Requirements 53 Directions for Use 74 Mechanical Instructions 105 Upgrade Software 136 Block Diagrams,Waveforms, Wiring Diagram 15Overall block diagram 15Wiring diagram 16Waveforms of Analog Board 17Waveforms of Digital Board 18Test Point Overview for Analog Board 19Test Point Overview for Digital Board 207 Circuit Diagram and PWB Layout 21Front: Front Panel - Display 21Layout: Front Display (Top View) 22Layout: Front Display (Bottom View) 22Front: Stanby 23Layout: Standby (Top View) 23Layout: Standby (Bottom View) 23Analog: PSU and Tuner 24Analog: Video input/output 25Analog: MSP 26Analog: Audio Converters 27Layout: Analog-Main Part (Top View) 28Layout: Analog-Main Part (Bottom View) 29Contents PageDigital: Back-end Processor 30Digital: Memory 31Digital: 1394 & USB Interface 32Digital: Interfaces 33Layout: Digital-Main Part (Top View) 34Layout: Digital-Main Part (Bottom View) 358 Exploded View & Spare Parts List 37Exploded View of the set 37Spare Parts List 38©Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.Version 1.01. Technical Specifi cations and Connection Facilities1.1 PCB Locations1.2 Diversity Matrix/97/75 /96Tuner PAL NTSC1.3 General:Power Supply : 110V-240V Mains Frequency : 50Hz 60HzPower consumption : 20W (typical)Standby Power consumption : 10kCAM (video) - CinchInput voltage : 1Vpp ± 3dB Input impedance : 751.5.2 Audio/Video Rear Input ConnectorsAudio - Cinch (L/R)Input voltage : 2.2Vrms max Input impedance : > 10kEXT1 VIDEO(CVBS) - CinchInput voltage : 1Vpp ± 3dB Input impedance : 75EXT2 S VIDEO (Y/C) HosidenAccording to IEC 933-5Superimposed DC-level on pin 4 (load > 100k):3.5V is detected as 16:9 aspect ratioInput voltage Y : 1 Vpp ± 3dBInput impedance Y : 75 Input voltage C : 300 mVpp ± 3dBInput impedance C : 75 Input impedance : > 10k1.5.3 Audio/Video Output ConnectorsAUDIO Cinch (L/R)Output voltage : 2 Vrms max.Output impedance : > 10kVIDEO (CVBS) CinchOutput voltage : 1 Vpp ± 3dBOutput impedance : 75 S-VIDEO (Y/C) - HosidenAccording to IEC 933-5Superimposed DC-level on pin 4 (load 100 k):3.5V is detected as 16:9 aspect ratioOutput voltage Y : 1 Vpp ± 3dBOutput impedance Y : 75 Output voltage C : 300 mVpp ± 3dBOutput impedance C : 75 COMPONENT VIDEO Cinch (Y/Pb/Pr)According to EIO-770-I-A, EIA-770-21.6 Digital Inputs / Outputs 1.6.1 IEEE 1394 Digital Video Input (DV IN)Implementation Standard according:IEEE Std 1394-1995 IEC61883 - Part 1IEC61883 - Part 2 SD-DVCR (02-01-1997)Specifi cation of consumer use digital VCRs using 6.3mm magnetic tape dec.1994Mechanical connection according to Annex of IEC 61883-11.6.2 Digital OutputDIGITAL AUDIO CinchLPCM : according IEC 60958MPEG 1, MPEG 2, AC3 : according IEC 61937DTS : according IEC 61937 + addendum1.7 Video Performance 1.7.1 SNRPALRGB CVBS Y/C 55 dB Lumincance: 55 dBChroma: 55 dB (AM) 52 dB (PM)Y: 57 dBC: 57 dB (AM) 54 dB (PM)NTSCY Pb Pr CVBS Y/C 55 dB Lumincance: 55 dBChroma: 54 dB (AM) 54 dB (PM)Y: 55 dBC: 54 dB (AM) 54 dB (PM)EN 33139 785 32500 1.Technical Specifi cations and Connection Facilities1.7.2 BandwidthPALRGB CVBS Y/C0.5 to 4 MHz:+1dB/-2dB0.5 to 4 MHz:+1dB/-2dBY:4.8MHz-3dB4.8 MHz:-3dB 4.8 MHz:-3dB C:700 kHz5.8 MHz:-6dB 5.8 MHz:-6dBNTSCYPbPr CVBS Y/C4.2 MHz:-3dB 4.2 MHz:-3dB Y:4.2MHz-3dB5.8 MHz:-6dB 5.8 MHz:-6dB C: 700 kHzWith Pscan: 8.4MHz -3dB1.8 Audio Performance CDDA (PCM)1.8.1 Cinch Output RearOutput voltage 2 channel mode : 2Vrms ± 1dBChannel unbalance (1kHz) : |0.22| dB (0.05V)Crosstalk 1kHz : |100| dBCrosstalk 16Hz-20kHz : |90| dBFrequency response : |0.2| dB Frequency response with de-emphasis : |0.5| dBSignal to noise ratio (unweighted) : - 95 dB Signal to noise ratio (A-weighted) : - 100 dBSignal to noise ratio (unweighted) : - 115 dBDynamic range 1kHz : |90| dBDistortion and noise 1kHz : -85 dBDistortion and noise 16Hz-20kHz : -85 dBIntermodulation distortion : 0.002 % (60 Hz and 7 kHz)Intermodulation distortion : 0.002 % (-94 dB) (19 kHz and 20 kHz)Phase Difference between channels: 1 samplePhase non-linearity : ± 2°Level non-linearity (-60dB to 90dB): |1.0| dBOutput polarity : 7FFF (H) positive pulse at output 8000 (H) negative pulse at outputMute : -95 dB (during spin- up, spin-down, pause and access)Outband attenuation : -40 dB above 30 kHz1.9 Dimension and WeightSet Dimension W x D x H : 360 x 43 x 322mmNet Weight : 3 kg1.10 Laser Output Power & Wavelength1.10.1 DVDOutput power during reading : 0.8mWOutput power during writing : 20mWWavelength : 650nm1.10.2 CDOutput power : 0.3mWWavelength : 780nm1.11 PlayabilityVideo Playback1. Disc playback media:CD, CD-R/-RW, DVD,DVD-Video, DVD+R/+RW, DVD-R/-RWSVCD, Video CD, DVD+R DL, DVD-R DLVideo disc playback system: PAL, NTSCx2. Compression formats:MPEG2, MPEG1, DivXxAudio Playback1. Disc playback media:CD, CD-R/-RW, MP3-CD, MP3-DVDx2. Compression formats:Dolby Digital, MP3, MPEG2 Multi-channel, PCMx3. MP3 bit rates: 32256 kbps and VBR xStill Picture Playback1. Disc formats:DVD+R/+RW, DVD-R/-RW,DVD+R DL, DVD-R DL, Picture CDx2. Picture Compression Format:JPEGx3. Picture enhancement: Rotate, Zoomx1.12 Supported Disc Types and Media Speed for RecordingDisc Media speedsDVD+R 1x - 16x DVD+RW 2.4 x - 4xDVD-R 1x - 16xDVD-RW 2x - 4xDVD+R DL 2.4x - 8xDVD-R DL 4xEN 4 3139 785 325001. Technical Specifi cations and Connection Facilities2.1 Safety Instructions2.1.1 General SafetySafety regulations require that during a repair: Connect the unit to the mains via an isolation transformer. Replace safety components, indicated by the symbol ,only by components identical to the original ones. Anyother component substitution (other than original type) may increase risk of fi re or electrical shock hazard.Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention tothe following points: Route the wires/cables correctly, and fi x them with themounted cable clamps. Check the insulation of the mains lead for externaldamage. Check the electrical DC resistance between the mains plug and the secondary side:1. Unplug the mains cord, and connect a wire betweenthe two pins of the mains plug.2. Set the mains switch to the on position (keep themains cord unplugged!).3. Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom.4. Repair or correct unit when the resistancemeasurement is less than 1 M.5. Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492).6. Switch the unit off, and remove the wire between the two pins of the mains plug.2.1.2 Laser SafetyThis unit employs a laser. Only qualifi ed service personnel may remove the cover, or attempt to service this device (due to possible eye injury).Laser Device UnitType : Semiconductor laser GaAlAsWavelength : 650 nm (DVD): 780 nm (VCD/CD)Output Power : 20 mW(DVD+RW writing): 0.8 mW(DVD reading): 0.3 mW(VCD/CD reading)Beam divergence : 60 degreeCLASS 1LASER PRODUCTFigure 2-1Note: Use of controls or adjustments or performance of procedure other than those specifi ed herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.2.2 Warnings2.2.1 General All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, ). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential.Available ESD protection equipment: Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. Wristband tester 4822 344 13999. Be careful during measurements in the live voltage section. The primary side of the power supply, including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is off!). It is possible to touch copper tracks and/ or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A lightning stroke and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. Never replace modules, or components, while the unit is on.2.2.2 Laser The use of optical instruments with this product, will increase eye hazard. Only qualifi ed service personnel may remove the cover or attempt to service this device, due to possible eye injury. Repair handling should take place as much as possible with a disc loaded inside the player. Text below is placed inside the unit, on the laser cover shield:Figure 2-22.2.3 NotesDolbyManufactured under licence from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confi dential Unpublished Works.©1992-1997 Dolby Laboratories, Inc. All rights reserved.Figure 2-3TrusurroundTRUSURROUND, SRS and symbol (fi g 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.Figure 2-42. Safety Information, General Notes & Lead Free RequirementsCAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAMADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLINGADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLENVARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLENVARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEENVORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAMATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS DOUVERTURE EXPOSITION DANGEREUSE AU FAISCEAUEN 53139 785 32500 2.Safety Information, General Notes & Lead Free RequirementsVideo Plus “Video Plus+” and “PlusCode” are registered trademarks of the Gemstar Development Corporation. The “Video Plus+” system is manufactured under licence from the Gemstar Development Corporation.Figure 2-5MacrovisionThis product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.2.3 Lead Free RequirementInformation about Lead-free produced setsPhilips CE is starting production of lead-free sets from 1.1.2005 onwards. INDENTIFICATION:Regardless of special logo (not always indicated) One must treat all sets from 1 Jan 2005 onwards, according next rules. Example S/N:Bottom line of typeplate gives a 14-digit S/N. Digit 5&6 is the year, digit 7&8 is the week number, so in this case 1991 wk 18So from 0501 onwards = from 1 Jan 2005 onwardsImportant note: In fact also products of year 2004 must be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this.Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-pate is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400°C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. Adjust your solder tool so that a temperature around 360°C 380°C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400°C otherwise wear-out of tips will rise drastically and fl ux-fl uid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid or does not know whether product is lead-free, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs:- always use the 12nc-recognizable soldering temperature profi le of the specifi c BGA (for de-soldering always use the lead-free temperature profi le, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYS-website.Do not re-use BGAs at all. For sets produced before 1.1.2005 (except products of 2004), containing leaded solder-alloy and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website www.atyourservice.ce.Philips.com you fi nd more information to: null BGA-de-/soldering (+ baking instructions)null Heating-profi les of BGAs and other ICs used in Philips-setsYou will fi nd this and more technical information within the “magazine”, chapter “workshop news”.For additional questions please contact your local repair-helpdesk.EN 6 3139 785 325002. Safety Information, General Notes & Lead Free RequirementsEN 73139 785 32500Directions For Use 3.3. Directions For UseThe following except of the Quick Use Guide serves as an introduction to the set.The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Cus