Philips-DVDR-9000-H-Service-Manual-2电路原理图.pdf

Published by KC-TE 0547 AV Systems Printed in the Netherlands Subject to modication EN 3139 785 31690DVDR9000HHDD & DVD RecorderService InstructionCLASS 1LASER PRODUCTContents Page1 Technical Specications and Connection Facilities 22 Test Disc & Repair Hints 53 Firmware Upgrading & Diagnostic Software 64 Service Flow chart 75 Directions For Use 12©Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.Version 1.0DVDR9000H/10The 2005 range DVD Recorder products are repaired centrally.Defective sets must be identied, labelled and stored for pick-up.This document gives full instructions for a functional check.Technical information to repair faulty sets is therefore not provided in this document.To test in-coming sets the following must be performed:1. Verify / Reproduce the customers problem2. Verify that set has latest Firmware (see chapter 3) and upgrade if it is not the latest version.3. Full functional checkEN 2 3139 785 316901. Technical Specications and Connection Facilities1. Technical Specications and Connection Facilities1.1 Read / Write SpeedType of Disc (Function) Disc Rotation SpeedRead Speed CD 7X CAV Read Speed DVD 4X CAV Write Speed DVD+R/+RW 2.4X ZCAVWrite Speed DVD-R/-RW 2X 1.2 General:Mains voltage : 198V 276V Mains frequency : 47 Hz 63 HzPower consumption (record) : 4.5V / 9.5V / 1V / 10kVideo - CinchInput voltage : 1Vpp ± 3dB Input impedance : 75Video - YC (Hosiden)According to IEC 933-5Superimposed DC-level on pin 4 (load = 100k)3.5V is detected as 16:9 aspect ratioInput voltage Y : 1Vpp ± 3dB Input impedance Y : 75Input voltage C : 300mVpp ± 3dBInput impedance C : 751.4.4 Out 1Component Video Cinch Y/Pb/Praccording EIO-770-I-A, EIA-770-2Audio - CinchOutput voltage : 2.2Vrms max.Output impedance : > 10k1.4.5 Out 2Audio - CinchOutput voltage : 2Vrms max.Output impedance : > 10kVideo - CinchOutput voltage : 1Vpp ± 3dB Output impedance : 75Video - YC (Hosiden)According to IEC 933-5Superimposed DC-level on pin 4 (load > 100k)3.5V is detected as 16:9 aspect ratioOutput voltage Y : 1Vpp ± 3dB Input impedance : 75Output voltage C : 300mVpp ± 3dBInput impedance : 751.5 Digital Inputs / Outputs 1.5.1 Digital OutputDigital Audio Coaxial / OpticalLCM : according IEC 60958MPEG 1, MPEG 2, AC3 : according IEC 61937DTS : according IEC 61937 + addendum1.5.2 HDMI OutputType A connector (19 pins)1.5.3 Digital Video Input (IEEE 1394)Implementation Standard according:IEEE Std 1394-1995 IEC61883 - Part1IEC61883 - Part 2 SD-DVCR (02-01-1997)Specication of consumer use digital VCRs using 6.3mm magnetic tape dec.1994Mechanical connection according to Annex of IEC 61883-1EN 4 3139 785 316901. Technical Specications and Connection Facilities1.10 PlayabilityDVDR9000HVideo Playback1. Disc Media:CD-R/-RW, MP3-CD, VCD/SVCD,DVD-Video, DVD+R/+RW, DVD-R/-RWx2. Compression Format:MPEG1, MPEG2xAudio Playback1. Disc Media:CD, CD-R/-RW, MP3-CDx2. Compression Format:Dolby Digital, MP3, MPEG2 Multi-channel, PCMx3. MP3 bit rates: 32-320 kbps xStill Picture Playback1. Disc Media:Picture CD, DVD+R/+RW, CD-R/-RWx2. Picture Compression Format:JPEGx1.5.4 G-Link (for IR-remote transmitting device)Output voltage : 5 ± 0.5V (high level)0.4 ± 0.3V (low level)Output impedance : 1501.6 Video PerformanceAll outputs loaded with 75SNR measurements over full bandwidth without weighting.1.6.1 SCART (RGB)SNR : 55dB on all outputBandwidth : 4.8MHz -3dB1.7 Audio Performance 1.7.1 Cinch Output RearOutput voltage 2 channel mode : 2Vrms ± 2dBChannel unbalance (1kHz) : 100dBCrosstalk 16Hz-20kHz : > 87dBFrequency response 20Hz-20kHz : ± 0.5dBSignal to noise ratio (unweighted) : > 85dBDynamic range 1kHz : > 83dBDistortion and noise 1kHz : > 83dBDistortion and noise 16Hz-20kHz : > 75dBIntermodulation distortion : > 70dBMute : > 95dB1.7.2 Scart AudioOutput voltage 2 channel mode : 1.6Vrms ± 2dBChannel unbalance (1kHz) : 85dBCrosstalk 16Hz-20kHz : > 70dBFrequency response 20Hz-20kHz : ± 0.5dBSignal to noise ratio (unweighted) : > 80dBDynamic range 1kHz : > 75dBDistortion and noise 1kHz : > 75dBDistortion and noise 16Hz-20kHz : > 50dBIntermodulation distortion : > 70dBMute : > 80dB1.8 Dimensions and WeightHeight of feet : 5.5mmApparatus tray closed : WxDxH:435x390x89mmApparatus tray open : WxDxH:435x525x89mmWeight without packaging : approx. 7.1 ± 0.5kgWeight with packaging : approx. 8.5kg1.9 Laser Output Power & Wavelength1.9.1 DVDOutput power during reading : 0.8mWOutput power during writing : 20mWWavelength : 650nm1.9.2 CDOutput power : 0.3mWWavelength : 780nmEN 53139 785 31690 2.Test Disc & Repair Hints2.1 Test Disc1) 7104 099 96611 CD-RW printed Audio Disc2) 9965 000 25728 DVD Player Test Pack3) - Blank DVD+RW4) - Blank DVD-RW2.2 Open the DVD Tray manuallyNote: This procedure needs to be performed on condition that:- a customers Disc is jammed in the DVD Tray- the DVD Tray cannot be open via the normal open/close button on the set.1) Place the set on the table with the bottom faced upwards as shown below.2) Insert a screw driver into the slot and open the DVD Tray by sliding the screw driver in the direction shown.Figure 2-12. Test Disc & Repair Hints12EN 6 3139 785 316903. Firmware Upgrading & Diagnostic Software3. Firmware Upgrading & Diagnostic Software3.1 Firmware UpgradingA. Preparation to upgrade rmware:1. Unzip the zip-archive le2. Start the CD Burning software and create a new CD project (data disc) with the following settings:File system : JolietFormat : MODE 2: CDROM XARecording mode : SINGLE SESSION (TRACK-AT-ONCE), FINALIZED CDNote: Long le name is necessary for the preparation of the upgrade disc3. Place the content of the zip-archive into the root directory of the new CD project.4. Burn the data onto a blank CDR or CD-RWB. Procedure to apply the rmware upgrade:1. Hold the + buttons down and Power up the set.2. The tray opens and set will display:FORCE DL >. PUT DSC3. Insert the prepared Upgrade CDROM and close the tray.4. The set will display:INIT DSC > . DOWNLOAD >.The whole process takes less than 15 minutesNote: Do not press any buttons or interrupt the mains supply during the upgrading process, otherwise the set may becomes defective.5. When the upgrade is completed the tray will open automatically and the set will display:REMOVE6. Close the tray and the set will display:DONE C. How to read out the rmware version to conrm set has been upgraded:1. Power up the set.2. Press button on the Remote control and select Setup option3. Press button to select System4. The set will prompt you about clearing the Time Shift Buffer5. Select Yes and press button6. Press button several times to select Version info7. Press button8. The TV connected to the set will display:DIF05_3/493AN SV11205BE 43.2.13 ASP3,9,1,10FPDTTM HW:01020102 DTTMSW:00040200SIT9000-FF3F-S3_F54020051020-1815 pro sxcplusintEPG:3.04 DPMS:P_DPM9. Press button to exitEN 73139 785 31690 4.Service Flow Chart4. Service Flow Chart4.1 Start ProcessStartA(Verification Test)Is it a Hardware problem ?Upgrade to latest FirmwareIs it a knowncomplaint ?Is Firmware solution available ?YesNoYesNoYesNoIs the complaint solved ?Return set to Customer with Report on action doneYesNoIs the complaint documented ?YesNoService W/S to contact the Trade / Customer to work out an action plan.Examples:- explain them that the Firmwaresolution is not ready- Upgrade disc will be send to them themoment a solution is ready- etc.Does the set pass the Dealer Test ?PassFailPerform built-in Dealer Test(Press & hold Play button on Front Panel down + Power-up the set)Send refurbished set from pool stock to Trade / customer- Attached Defect Description Reportand Proof of Purchase.- Pack defective set- Store defective set for pick-upEN 8 3139 785 316904. Service Flow Chart4.2 Verication Process* If complaint is related to System Menu settingConnect up the Recorder to TV antenna, TV set and an External sourceCheck the Firmware version on the setCan the set Start-up ?YesNoA(Verification Test)BRecording CheckCPlayback CheckD *System MenuSend refurbished set from pool stock to Trade / customerReturn set to Customer with Report on action done- Attached Defect Description Report andProof of Purchase.- Pack defective set- Store defective set for pick-upNoYesIs Firmware the last released version ?Upgrade to latest FirmwareAre the checks result ok ?YesNoEN 93139 785 31690 4.Service Flow Chart4.3 Recording ProcessManual Recording with TSB HDD: Manual RecordingCopy to DVD Recordable disc Timer RecordingDoes Timer recordingfunctions ?YesNoDoes manual recordingfunctions ?YesNoBRecordingCheckMake a Timer recording with:- VPS/PDC on and off- Guide Plus+ System- Show View System- manual recordingPlayback the recorded title from HDD browserAre Timer edit & delete feature working ?YesNoMake a manual recording to the HDD using different recording source:- Cam 1 (Front CVBS/S-Video)- Cam 2 (DV-in)- Tuner- Rear Ext 1/2 (external CableBox/Satellite Receiver/VCR/DVD)From the HDD browser select the recorded title and check the following:- edit title feature- play the titleDoes theTSB feature works ?1) Switch the Recorder to Tuner source- The active Tuner channel will berecorded into the TSB (time shiftbuffer), a temporary HDD storagearea.2) By pressing the “INFO“ button theTime shift bar appears on the screen,check the following features:- search forward / backward- instant replay, pause, etc. on thelive TV function1) Make a short recording (1 minute) byselecting a portion in the TSB to berecorded.2) Playback the recorded title from theHDD browserDoes the recordingfunctions ?ContinueContinueYesNoYesNoSend refurbished set from pool stock to Trade / customer- Attached Defect Description Report andProof of Purchase.- Pack defective set- Store defective set for pick-up1) Insert a DVD+RW disc2) In the HDD browser select the recordedtitle for copy to recordable DVD3) From the Disc Menu select the copiedtitle and check the following:- edit (Disc/Title) feature- play the title4) Repeat with DVD-RWDoes copy function ?YesNoIs the Disc Library feature working ?YesNoEN 10 3139 785 316904. Service Flow Chart4.4 Playback ProcessHDD playback Check Disc playback CheckYesNoCPlaybackCheckPlaying other type of disc:1) Use discs of DVD PLAYER TEST PACK for:- (Super) Video CD- MP3 disc- Picture disc (slide show)- special DVD playback check by layer change test usingDVD disc of this package2) For AUDIO CD use of CD-RW printed Audio Disc to check:- Track 3 finger print- Track 8: 600u black dot (max. after 1 min.)From the DVD browser go through the Content, Title & Toolbar optionsPlay a DVD video disc title and check the following:- Pause, Search Fwd/Rev & Next /Previous chapter- Edit features- T/C searchYesNoDoes the set work ?From the HDD browser check the following features:- Sorting- Delete, Copy & Protect- Edit featuresDoes the set work ?ContinueContinueYesNoSend refurbished set from pool stock to Trade / customer- Attached Defect Description Report andProof of Purchase.- Pack defective set- Store defective set for pick-upDoes the set work ?Play a title from the HDD browser and check the following features:- Pause, Search Fwd/Rev & Next /Previous chapter- Editing features- YesNoDoes the set work ?