Philips-DVD-580-M-Service-Manual电路原理图.pdf
Published by MW 0267 Service PaC©Copyright 2002 Philips Consumer EAll rights reserved. No part of this publretrieval system or transmitted, in anymechanical, photocopying, or otherwDVD-Video Player DVD580MDVD580M /691 /001Power Board 31 32Front Board 33 34Decoder Board: Processor and Memory 35 37-38Decoder Board: Audio Interface 36 37-38AV Board (NON-EU) 39 40AV Scart Board (EU) 41 42Karaoke Board 43 43E Printed in the Netherlands Subject to modification EN 3122 785 12290lectronics B.V. Eindhoven, The Netherlands. ication may be reproduced, stored in a form or by any means, electronic, ise without the prior permission of Philips.8 Alignments(Not Applicable) 459 Circuit Descriptions 4510 Spare Parts List 532 Safety Instructions, Warnings, Notes, and Service Hints 33 Directions for Use 44 Mechanical- and Dismantling Instructions 135 Diagnostic Software, Trouble Shooting and Test Instructions(Not Applicable) 176 Wiring-, Block DiagramsBlock Diagram 29Wiring Diagram 307 Electrical Diagrams and Print-Layouts Diagram PWBCL 26532085_000.eps180702Contents Page1 Technical Specs and Connection Facilities 2Technical SpecificationsEN 2 DVD580M1.1. Technical SpecificationsCL 26532085_073.eps180702Safety Instructions, Warnings, Notes, and Service Hints EN 3DVD580M 2.2. Safety Instructions, Warnings, Notes, and Service Hints2.1 Safety Instructions2.1.1 General SafetySafety regulations require that during a repair: Connect the unit to the mains via an isolation transformer.Replace safety components, indicated by the symbol g19, only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points:Route the wires/cables correctly, and fix them with the mounted cable clamps.Check the insulation of the mains lead for external damage.Check the electrical DC resistance between the mains plug and the secondary side:1. Unplug the mains cord, and connect a wire between the two pins of the mains plug.2. Set the mains switch to the 'on' position (keep the mains cord unplugged!).3. Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4. Repair or correct unit when the resistance measurement is less than 1 M. 5. Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492).6. Switch the unit off, and remove the wire between the two pins of the mains plug.2.1.2 Laser SafetyThis unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury).Laser Device UnitType : Semiconductor laser GaAlAsWavelength : 650 nm (DVD): 780 nm (VCD/CD)Output Power : 20 mW (DVD+RW writing):0.8 mW (DVD reading): 0.3 mW (VCD/CD reading)Beam divergence : 60 degreeFigure 2-1 Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.2.2 Warnings2.2.1 GeneralAll ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, g34). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. Wristband tester 4822 344 13999.Be careful during measurements in the live voltage section. The primary side of the power supply (pos. 1005), including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is 'off'!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A 'lightning stroke' and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply.Never replace modules, or components, while the unit is on.2.2.2 LaserThe use of optical instruments with this product, will increase eye hazard.Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury.Repair handling should take place as much as possible with a disc loaded inside the player.Text below is placed inside the unit, on the laser cover shield:Figure 2-2 2.2.3 NotesDolbyManufactered under licence from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.Figure 2-3 TrusurroundTRUSURROUND, SRS and symbol (fig 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.Figure 2-4 CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLINGADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLENVARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTE LYLLE ÄLÄ KATSO SÄTEESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSENDANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYO NNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU!Directions for UseEN 4 DVD580M3.3. Directions for Use Directions for Use EN 5DVD580M 3.Directions for UseEN 6 DVD580M3.Directions for Use EN 7DVD580M 3.Directions for UseEN 8 DVD580M3.Directions for Use EN 9DVD580M 3.Directions for UseEN 10 DVD580M3.
