Philips-DVD-625-Service-Manual电路原理图.pdf

Published by MW 0363 Service PaCE©Copyright 2003 Philips Consumer ElAll rights reserved. No part of this publretrieval system or transmitted, in anymechanical, photocopying, or otherwise wiDVD-Video Player DVD625DVD625 /001 /021 /051Power Supply Unit 27 28Front Board 29 30MPEG Board: Index (Diagram M1) 31 36-37MPEG Board: RF Part (Diagram M2) 32 36-37MPEG Board: Servo Part (Diagram M3 33 36-37MPEG Board: Mem. & Audio (Diagram M4) 34 36-37MPEG Board: Video Part (Diagram M5) 35 36-37Printed in the Netherlands Subject to modification EN 3122 785 13390ectronics B.V. Eindhoven, The Netherlands. ication may be reproduced, stored in a form or by any means, electronic, thout the prior permission of Philips.8 Alignments (Not Applicable) 399 Circuit Descriptions (Not Applicable) 3910 Spare Parts List 4010 Revision List 432 Safety Instructions, Warnings, Notes, and Service Hints 33 Directions for Use 54 Dismantling Instructions and Exploded View 175 Diagnostic Software, Trouble Shooting and Test Instructions 196 Wiring-, Block DiagramsBlock Diagram 25Wiring Diagram 267 Electrical Diagrams and Print-Layouts Diagram PWBCL 36532022_000.eps190303Contents Page1 Technical Specifications 2Technical SpecificationsEN 2 DVD625 /0x11.1. Technical SpecificationsSafety Instructions, Warnings, Notes, and Service Hints EN 3DVD625 /0x1 2.2. Safety Instructions, Warnings, Notes, and Service Hints2.1 Safety Instructions2.1.1 General SafetySafety regulations require that during a repair: Connect the unit to the mains via an isolation transformer. Replace safety components, indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points: Route the wires/cables correctly, and fix them with the mounted cable clamps. Check the insulation of the mains lead for external damage. Check the electrical DC resistance between the mains plug and the secondary side:1. Unplug the mains cord, and connect a wire between the two pins of the mains plug.2. Set the mains switch to the 'on' position (keep the mains cord unplugged!).3. Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4. Repair or correct unit when the resistance measurement is less than 1 M. 5. Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492).6. Switch the unit off, and remove the wire between the two pins of the mains plug.2.1.2 Laser SafetyThis unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury).Laser Device UnitType : Semiconductor laser GaAlAsWavelength : 650 nm (DVD): 780 nm (VCD/CD)Output Power : 20 mW (DVD+RW writing): 0.8 mW (DVD reading): 0.3 mW (VCD/CD reading)Beam divergence : 60 degreeFigure 2-1 Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.2.2 Warnings2.2.1 General All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, ). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. Wristband tester 4822 344 13999. Be careful during measurements in the live voltage section. The primary side of the power supply (pos. 1005), including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is 'off'!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A 'lightning stroke' and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. Never replace modules, or components, while the unit is on.2.2.2 Laser The use of optical instruments with this product, will increase eye hazard. Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury. Repair handling should take place as much as possible with a disc loaded inside the player. Text below is placed inside the unit, on the laser cover shield:Figure 2-2 2.2.3 NotesDolbyManufactered under licence from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.Figure 2-3 TrusurroundTRUSURROUND, SRS and symbol (fig 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.Figure 2-4 CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLINGADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLENVARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSENDANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYO NNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU!Safety Instructions, Warnings, Notes, and Service HintsEN 4 DVD625 /0x12.2.3 Service Hints2.3.1 Repair tipsSwitched mode power supplyThe power supply unit has to be replaced in case of failure. The schematic diagram provided in the service manual is only for information and no service parts will be available.DVD Loader The DVD Loader is a non-repairable unit and in case of failure, it has to be replaced with a complete DVD Loader. Mpeg board and Front DisplayThe Mpeg board and Front display has to be repaired down to component level. 2.3.2 Change of Software settingThe software setting can be change according to the following procedure:1. Press “OPEN/CLOSE” button on the front of the player to open the disc tray.2. Enter the 4-digit code on the remote control.3. Enter one of the keys below to change the software setting.REGION CODE USA => 1EUROPE => 2AP => 3LATAM => 4INDIA / RUSSIA => 5CHINA => 6SUBTITLE 7:Set to setup configuration ofDVD625 / 001SUBTITLE 7:Set to setup configuration ofDVD625 / 021SUBTITLE 7:Set to setup configuration ofDVD625 / 0514. The change should effect immediately with information indicated on TV screen.Note: When changing the setup configuration, the change will take immediate effect with the informationindicated on the TV screen for a short period and the tray will close automatically and player will go to standby.2.3.3 Software upgrade via Download discBoth the application and servo software are delivered in one sw stack and it can be flashed into the DVD player by means of a CD-ROM disc. The CD-ROM disc has to be made with a CD writer SW.Note: 1. The file name used for writing on the CD-R/RW MUST be in UPPER-CASE.eg: SD542PH.BIN2. For better and fast reading, add one big garbage file of 50-100MB.Software upgrade procedure1. Open disc tray on the player.2. Insert the DOWNLOAD DISC into the player and close disc tray.3. The upgrading operation will start automatically.4. The VFD will display the upgrading progress, ERASE.WRITE F.WRITE 0 UPGRADE end or the LED will turn ON and OFF)5. The upgrading will take approximately about 1 minute.6. Once when the software is upgraded, the disc tray will automatically eject.7. The player will be restarted automatically and display on Important note:Do not power off or interrupt the mains during the upgrading else the player's flash memory will be erased.2.3.4 Verify settingTo check that the setting has change successfully.1. Press “DISPLAY” button on the remote control while disc tray is open.2. Two lines text will appear on the TV screen. That is how it looks like.SD542PH-030219-728-001NSERVO:001FC72 REG:2In text, the following numbers refer to:SD542PH-030219 => refer to Application software versionREG 2 =>refer to region codeSERVO:001FC72 => refer to servo software version625-001N => refer to setup configuration of a type number,eg. DVD625/0012.3.5 ComPairThere is no ComPair available2.4 Service Tools Test discs Audio signals disc 4822 397 30184 Torx screwdrivers Set (straight, T2 to T20 4822 395 50145 Set (square, T10, T15, T20to T20 4822 395 501322.5 Revision InformationService Manual Version : 1.0Issue Date : February 21, 2003Revision Information : N/AVFD will show “NO DISC”.Directions for Use EN 5DVD625 /0x1 3.3. Directions for UseDirections for UseEN 6 DVD625 /0x13.Directions for Use EN 7DVD625 /0x1 3.Directions for UseEN 8 DVD625 /0x13.Directions for Use EN 9DVD625 /0x1 3.Directions for UseEN 10 DVD625 /0x13.