grundig s800 MANUAL 电路原理图.pdf
RadioFans.CNFRONT PANEL DESCRIPTION (See page 12) LCD DISPLAY DESCRIPTION (See page 14) REAR PANEL DESCRIPTION (See Paee 15) 3 RadioFans.CN SPECIFICATIONS Frequency Range: 100 to 30.000 kHz (0.1 to 30 MHz). Line Audio Outputs: Stereo left and right. 87 to 108 MHz, 118 to 137 MHz. 300 mV. 4.7K Ohms for each output. Sensitivity - SSB AM. USB. LSB modes (0.1 to 30 MHz). AM mode only for 118 to 137 MHz. FM mode only for 87 to 108 MHz. Headphone Jack: DC Power Requirements: 1/8 inch (3.175mm) stereo/mono type. Input: 7-10 VDC 0 1 Amp. supplied from AC ADAPTER, external DC Power (10 dB S+N/N): Less than 0.5 uV, 0.1 to 30 MHz. Supply or 5.7 to 9.0 VDC supplied by (6) Sensitivity - AM internally mounted “D“ cell (1.5V) batteries (not supplied). (10 dB S+N/N): (1000 Hz. 30% Mod): Less than 2.0 uV. 0.1 to 30 MHz. Less than 4.0 pV, 118 to 137 MHz. Current requirements Sensitivity - FM (approximate) from 9.0 VDC Supply or (20 dB S/N) (monaural): Frequency Stability Less than 4 uV, 87 to 108 MHz. 10 ppm, 0C to 50C Batteries with 1/4 W average Audio Output: Mode Dependent: 510 mA minimum with lamp off, Frequency Accuracy: Better than 100 Hz. c 25' C Operating Temperature: 830 mA maximum with lamp on. 0C to +50C Selectivity - SSB. AM: 6 kHz c -6 dB, less than 12 kHz 0 -60 dB. 4 kHz c -6 dB. less than 9 kHz c -60 dB. 2.3 kHz c -6 dB, less than 5 kHz c -60 dB. Weight: 14.55 lbs. (6.6 kg). including AC ADAPTER, (batteries NOT included). IF Frequency - SSB. AM: 1st IF. 55.845 MHz. Size - Width: 20 -7/8“ (53.575 cm). FM: Image Rejection: IF Rejection. IP3 - Intercept Point 2nd IF, 455 kHz. 1st IF. 10.7 MHz (Single Conversion). Greater than 60 dB. 0.1 to 30 MHz Greater than 60 dB, 118 to 137 MHz. Greater than 50 dB. 87 to 108 MHz Greater than 80 dB. 55.845 MHz. Greater than 80 dB. 455 kHz. Height: Depth: Supplied AC ADAPTER Input: Output: 9-1/4“ (23.495 cm) with handle retracted. 8 1/2“ (21.59 cm) including front handles. 120-230 VAC auto switchable. 50/60 Hz with dual switchable plug wires. 9 VDC 1500 mA maximum. Center conductor of connector is positive. (± 50 Ohm Ant. Input) (Attenuator Off): AGC Performance Internal Antenna External Antenna Inputs External Speaker Output Power to Internal Speaker: Internal Speaker Greater than +10 dBm 100 kHz spacing. Greater than -20 dBm Q 5 kHz spacing. Threshold: 1 0 uV Attack Time. 1 mSec. Release Time: SLOW. 3 sec FAST. 300 mSec Less than 6 dB change in audio output for 90 dB RF input change (referenced from the AGC threshold point plus 3 dB). 56 3/4“ (1.414 meters) telescoping whip (for use on all bands). Ferrite rod antenna (For use from 100 kHz through 1800 kHz) 0 1 to 30 MHz. 50 Ohm SO-239 connector or 2 terminal compression connector for 500 Ohm input with ground 87 to 108 MHz and 118 to 137 MHz 75 Ohm “F“ type connector 1 Watt each nominal into two 4 Ohm speakers with 9 VDC supply voltage External jack is 1/4“ (6.35 mm) and two-way for stereo output 2 Watts nominal when neither headphones nor external speakers are plugged in 4'(10 16 cm), 4 Ohms. 4 RadioFans.CN 5An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the appliance and cart combination to overturn. The lightning flash with arrow head symbol, within an equilateral triangle,is intended to alert the user to the presence of uninsulated “dangerous voltage“ within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT'S AC ADAPTER TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET, REFER SERVICING TO QUALIFIED PERSONNEL ONLY CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THE AC ADAPTER WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES OF THE AC ADAPTER CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. ATTENTION: POUR PREVENIR LES CHOCS ELECTRIQUES, NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT. 1. Read Instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. 5. Cleaning-Unplug this appliance from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleansers. Use a damp cloth for cleaning. 6. Attachments-Do not use attachments that are not recommended by the manufacturer or they may cause hazards. 7. Water and Moisture-Do not use this product near water-for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool- and the like. 8. Accessories-Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. 9. Ventilation-This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Any slots or openings in the,cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. KEEP CURTAINS AND OTHER FLAMMABLE MATERIALS OUT OF DIRECT CONTACT WITH THE AC ADAPTER. WARNING. TO PREVENT FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE THIS PRODUCT'S AC ADAPTER TO RAIN OR MOISTURE 10. Power Sources-This product should be operated only from the type of power source indicated on the marking label of the supplied AC Adapter. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company. 11. Lightning-For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug the AC adapter from the wall outlet. 12. Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them may be fatal. 13. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 14. Servicing-Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 15. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the AC adapter cord or plug is damaged. b. If the AC adapter has been exposed to rain or water. c. It the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. An improper adjustment may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. d. If the product has been dropped or the cabinet has been damaged. e. When the product exhibits a distinct change in performance-this indicates a need for service. 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock or other hazards. 17. Safety Check-Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 18. Outdoor Antenna Grounding-Before attempting to install this product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. a. Use No.10 AWG (5.3mm 2 ) copper, No.8 AWG (8.4mm 2 ) aluminum, No.17 AWG (1.Omm 2 ) copper-clad steel or bronze wire or larger, as ground wire. b. Secure antenna lead-in and ground wires to house with stand-off insulators spaced from 4 feet (1.22m) to 6 feet (1.83m) apart. c. Mount antenna discharge unit as close as possible to where lead-in enters house. d. A driven rod may be used as the grounding electrode where othertypes of electrode systems do not exist. Refer to the National Electrical Code, ANSI/NFPA 70-1990 for information. e. Use jumper wire not smaller than No.6 AWG 13.3mm 2 ) copper or equivalent, when a separate antenna grounding electrode is used. EXAMPLE OF ANTENNA GROUNDING RadioFans.CNTABLE OF CONTENTS Thank you for purchasing the GRUNDIG SATELLIT 800 MILLENNIUM Shortwave Receiver. This receiver has been designed and manufactured to high quality standards, and will provide reliable operation for many years. Please carefully read the Owner's Manual in order to take advantage of the many interesting features that will provide enjoyable listening to radio broadcasts around tha world SPECIFICATIONS 4 MEMORY DESCRIPTION 19 IMPORTANT SAFEGUARDS 5 STORING A MEMORY CHANNEL 19 RECALLING A MEMORY LOCATION 19 TABLE OF CONTENTS 6 DELETING A MEMORY LOCATION 19 GENERAL DESCRIPTION 7 SCAN FUNCTIONS 20 SCAN DESCRIPTION 20 POWER SUPPLY 8 MEMORY CHANNEL SKIP 20 AC ADAPTER 8 BATTERY OPERATION CLOCK AND TIMER FUNCTIONS 21 AND INSTALLATION 8 TIME DISPLAY 21 SETTING THE 24 HOUR CLOCKS 21 INSTALLATION 10 TIMER OPERATION 21 UNPACKING 10 SETTING TIMER ON/OFF TIMES 22 LOCATION 10 ENABLING/DISABLING FIXED INSTALLATION 10 TIMER OPERATION 22 PORTABLE OPERATION 10 ANTENNA REQUIREMENTS 10 SPECIAL USE FEATURES AND FUNCTIONS 25 LOCK ALL ENTRY TO KEYPAD 25 FRONT PANEL DESCRIPTION 12 BROADCAST BAND TUNING STEP SIZE 25 DELETE ALL MEMORY CHANNELS 25 LCD DISPLAY DESCRIPTION 14 AUTOMATIC BANDWIDTH SETTING REAR PANEL DESCRIPTION 15 WITH MODE SELECTION DISABLE (ENABLE) 25 GETTING STARTED 16 QUICK REFERENCE GUIDE 26 GENERAL OPERATING INFORMATION 16 GLOSSARY OF TERMS 29 MICROPROCESSOR RESET 16 BEEP TONES 16 TROUBLESHOOTING 30 FIRST STEPS 16 DIRECT FREQUENCY ENTRY 16 SUGGESTED REFERENCES 30 SHORTWAVE 'METER' BAND DESIGNATOR ENTRY 17 SERVICE INFORMATION 31 FREQUENCY RESOLUTION 17 FRONT PANEL LOCK (UNLOCK) 17 ONE YEAR LIMITED WARRANTY 31 AM SYNCRONOUS OPERATION 17 SSB OPERATION 18 MEMORY CHANNEL LOG 32 FM OPERATION 18 AGC OPERATION 18 6 RadioFans.CNGENERAL DESCRIPTION The SATELLIT 800 MILLENNIUM is a microprocessor controlled, synthesized, world band receiver with con- tinuous coverage capability from 100 kHz through 30 MHz which includes the AM broadcast and shorwave bands. Reception also includes FM broadcast (87 - 108 MHz) and Aircraft (118 -137 MHz) bands. The SATELLIT 800 MILLENNIUM offers excellent sensitivity, selectivity, dynamic range, and features that permit easy tuning of desired stations. Conveniently located front panel controls allow for rapid operator programming and ease of use. The unit can be operated from either the supplied AC ADAPTER or from six “D“ cell batteries (not supplied) for portable operation. A low battery voltage indication is displayed when that condition exists. Three electronically switched IF filters are provided. The front panel liquid crystal display provides feedback of the current status of the receiver. The seven digit frequency display provides resolution to 100 Hz accuracy in the AM broadcast, Aircraft and Shortwave bands. Resolution to 20 kHz is displayed in the FM broadcast band mode. Backlighting of the display is selectable by a front panel button. To prolong battery life with internal battery operation, the backlighting automatically turns off after a short delay following a function change or retuning of the receiver. Reception modes include Lower/Upper Sideband (LSB), (USB), and AM in the Shortwave, and AM broadcast bands. For the Shortwave and AM broadcast bands, a selectable sideband synchronous detector (SYNC) allows for enhanced reception by eliminating or reducing distortion due to fading signals. During FM broadcast use, stereo reception is available through the use of headphones. Other built-in reception aids include selectable slow or fast AGC, RF attenuator for use in strong signal handling conditions, as well as treble and bass controls. Two independent, real time clocks provide a local and alternative time selection. Also provided is a two event timer. A programmable memory area allows for 70 independent receiver set up memories. These memories do not require battery backup and are thus unaffected by power interruptions. All parameters associated with a particular memory channel are stored including the frequency, mode, bandwidth, fast or slow AGC, RF attenuator and synchronous detector. These memory channels may be accessed manually or through a time scan with each channel monitored for a 5 second period. 7 RadioFans.CNPOWER SUPPLY AC ADAPTER Keep curtains and other flammable materials out of The SATELLIT 800 MILLENNIUM receiver is supplied direct contact with the AC ADAPTER to avoid overheat with an auto-switchable AC ADAPTER to power it ing. indoors. The AC ADAPTER is designed to be plugged into a wall outlet that supplies nominal 120 VAC, 60 Hz GRUNDIG assumes no responsibility for damage or nominal 230 VAC 50 Hz power. due to operation with an AC adapter other than the The AC adapter is supplied with a North American type connector. To use the unit in countries using a European one supplied with this unit. BATTERY OPERATION AND INSTALLATION type connector, plug the North American connector into The SATELLIT 800 MILLENNIUM receiver is designed the US to Europlug adapter that is provided. to operate from either the supplied AC ADAPTER or Connect the output connector of the AC adapter to the from six “D“ cell batteries (not supplied). NOTE: Check the batteries periodically for leakage. IF UNIT IS TO 9 VDC, 1 amp connector on the back of the rece