Philco_H2010-Safari-Sams-475-2电路原理图.pdf
PHOTO FACT8 Folder with ClRCUMRACE* PHILCO MODELS H2O1OBL, H2O1OL (Ch. 1OAT1O) DISASSEMBLY INSTRUCTIONS CHASSIS REMOVAL 1. Remove all external push-on type knobs except the Elap- sed-Time knob. 2. Remove 4 metal screws on bottom holding cabinet stand and lower section of cabinet to the chassis. 3. Remove 2 metal screws at rear and one in front holding top plastic housing. Remove antenna connection from tuner. Remove metal screw holding ground strap. Re- move top plastic housing. 4. Remove 2 metal screws at rear and one at front of opti- cal system. Remove optical unit. 5. Remove5 metal screws holding battery mounting bracket. Remove bracket. 6. Remove chassis. PICTURE TUBE REMOVAL 1. Remove chassis. 2. Remove picture tube socket, sleeve and magnet assembly, and HV lead. 3. Slide the picture tube out the top of chassis. MODEL H2010L (SAFARI) CHASSIS 10AT10 TRADE NAME Philco Models H2010BL, H2010L (Safari) (Ch. 10AT10) MANUFACTURER Philco Corp., Tioga SOOOmmf (2200mnif) TERMINAL VIEW LI TERMINAL VIEW 12 COLLECTOR TRANSISTOR BASING COLLECTOR /BASE EMITTER EMITTER XI THRU X7 X8THRUX14 X16 AC voltage measured at 1000 ohms unless otherw nslt. umbers bottom of s are counted in clockwise direction o xket. 4. Lin 5. All s Voltage controls s se stated. maintained at et for normal ocke T17 pin to olts for operation; n comm voltoc, o sign n negative e readings. al applied, A PHOTOFACT STANDARD NOTATION SCHEMATIC Howard W. Sams & Co., Inc. I960 PAGE 2 RadioFans.CN SOUND TAKE-OFF AND VIDEO CONNECTIONS USED IN SOME VERSIONS - RadioFans.CN IGHSIDEOF RAST CONTROL AUDIO DRIVER 16 TERMINAL GUIDE AUDIO OUTPUT T7 TERMINAL GUIDE JSED IN SOME VERSIONS r .33 (543)|L2n,e<, 1W El W| PHILCO MODELS H2O1OBL, H2O1OL (Ch. 1OAT1O) RadioFans.CN TRANSISTOR AND TUBE PLACEMENT CHART CHANNEL SELECTOR E TUNING OSCILLATOR MIXER RFAMP T1597 _ T1600 _ T1561 SWEEP PRINTED BOARD CHASSIS AND VERT OUTPUT PRINTED BOARDVIDEO, SOUND, SYNC PRINTED BOARD o go 00 5 O So TRANSISTOR AND TUBE FAILURE CHECK CHART The following chart lists tubes and transistors whose failures are most likely to produce indicated symptoms. Refer to Transistor & Tube Placement Chart for location of tubes and transistors. POWER SUPPLY FAILURE No raster, no sound Fuse(l.GA), Rect. (B-t-) SWEEP FAILURE No raster, has sound X16, X17, X18, Diode (Damper), VI, V2, V3 No vertical deflection X14, X15 Poor vert, linearity or foldover X14, X15 Poor horiz. linearity or foldover X16, X19, X18, Diode (Damper) Narrow picture Rect. (B+), X16, X17, X18, Diode (Damper) Vert, off freq. X14 Horiz. off freq. X16 LOSS OF PICTURE OR SOUND No pic, no sound, has raster XI, X2, X3, X4, Diode (Video Det), X5 No pic, no sound, has snow X201, X202, X203, XI No pic, has sound, has raster X6, V3 Has pic, no sound XI, X8, X9, MO, Xll SYNC FAILURE No vert, sync X13 No horiz. sync X13 No vert, or horiz. sync X13 m 70 K) SET 475 FOLDER 2 PAGE 3 RadioFans.CN CircuiTrace Numbers 1 thru 48 A Howard W. Sams PAGE 4 CIRCUITRACE*Photo VIDEO, SOUND, SYNC PRINTED BOARD RadioFans.CN CircuiTrace Numbers 92 thru 139 T31 138 134 129 136 127 A Howard W. SamiCIRCUITRACEPhoto SWEEP PRINTED BOARD o ll o o m O X 58 5S O r 0 m 70 to SET 475 FOLDER 2 PAGE 5 RadioFans.CN ALIGNMENT INSTRUCTIONS PRE-ALIGNMENT INSTRUCTIONS The High Voltage lead should be securely taped and kept away from the chassis. Set Range switch to Normal and Drive Level control (R7) to mid-position. Suggested Alignment Tools: AlthruA9 GENERAL CEMENT * 6009, 8195, 8274, 8275, 8728, 8987 WALSCO #2531 A10, A12, A13 GENERAL CEMENT #8282, 8606, 8606L, 9295 WALSCO #2526, 2543, 2544, 2545 VIDEO IF ALIGNMENT Connect the synchronized sweep voltage from the sweep generator to the horizontal input of the oscilloscope for horizontal deflection. The generator output lead should be terminated with its characteristic impedance, usually 50 ohms. Use only enough sweep generator output to provide a usable pattern on scope. Connect a variable bias supply between TP-3 and chassis. The required bias will range from -1.5 to +3 volts. During alignment set bias to -K 2 volts unless otherwise stated. Adjust Al and A2 so that top of inner core is flush with top of outer core. SWEEP GENERATOR COUPLING Unplug IF cable from tuner and connect gener- ator across cable plug. Across antenna input jack. Reconnect IF cable. 11 SWEEP GENERATOR FREQUENCY Not used 69MC (10MC Swp) MARKER GENERATOR FREQUENCY 39. 75MC (4001, 30% AM Mod) 41. 25MC 47. 2 SMC 45.3MC 45. OMC 44. OMC 65. 75MC 44. 7MC 42. SMC 45. 75MC CHANNEL 4 CONNECT SCOPE Vert. Amp. to TP-4. Low side to chassis. ADJUST A3 A4, Ag A6 A7 AS A9 Fine Tuning Mixer Collectoi Coil REMARKS Adjust for MINIMUM scope indication. Raise bias at TP-3 in positive direction if necessary to obtain usable scope de- flection being careful not to overload. Adjust for maximum scope indication. Adjust for MINIMUM scope indication. DO NOT disturb for balance of alignment. Adjust for maximum scope Indication. Use peak nearest top of coil. Check for response curve similar to Fig. 1. If necessary, retouch Mixer Collector coil to correct high frequency side of curve, A5 for low frequency side and A7 for correct tilt. SOUND IF ALIGNMENT Connect the negative lead of a 3 volt bias supply to TP-3. Positive to chassis. SIGNAL GENERATOR COUPLING High side thru 10K to TP-4. Low side to chassis. 11 SIGNAL GENERATOR FREQUENCY 4. SMC (400% 30% AM Mod) CHANNEL Any non- interfering CONNECT VTVM DC probe to point . Common to chassis. ADJUST A10, All A12, A13 REMARKS Adjust for maximum deflection. (All not used in some sets). Preset for maximum core separation. Adjust for maximum deflection using first peak turning in. Adjust A13 for maximum deflection using first peak turning in. Disconnect test equipment and tune in a weak air signal. Retouch A12 for MINIMUM noise or distortion. 10. 11. F IG.I PAGE 6 RadioFans.CN TUNER ALIGNMENT INSTRUCTIONS 76-11773(1110) PRE-ALIGNMENT INSTRUCTIONS The High Voltage lead should be securely taped and kept away from the chassis. Suggested Alignment tools: A201, A208, A210, A212, A219 thru A222 GENERAL CEMENT #5009, 8195, 8274, 8275, 8728, 8987 WALSCO #2531 A217, A218 GENERAL CEMENT #5004, 5008, 5009 WALSCO #2520 OSCILLATOR ALIGNMENT Set the Fine Tuning to the center of its range. The generator output lead should be terminated with its characteristic impedance, usually 50 ohms. Use only enough sweep generator output to provide a usable pattern on scope. Coils not containing slugs are adjusted by bending toward or away from switch wafer. DUMMY ANTENNA Direct SIGNAL GENERATOR COUPLING Across antenna terminals. ii SIGNAL GENERATOR FREQUENCY 209. 75MC (400 30% AM Mod) 203.75MC 197. 75MC 191. 75MC 185.75MC 179. 75MC 173.75MC 81. 75MC 75. 75MC 65.75MC 59. 75MC 53.75MC CHANNEL 13 12 11 10 9 8 7 6 5 4 3 2 CONNECT SCOPE Across Video Det.load . ADJUST A201 A202 A203 A204 A205 A206 A207 A208 A209 A210 A211 A212 REMARKS Adjust for MINIMUM scope indication. M M .- II M , Video Sound T$tefe OR DIPA T 30*/ 76* 1 F IG.20I Video jIL* IMCMAxV OR DIP/70* -_-. , an* / I T iSound 3M7 50 -.70*1 F IG.202o RF AND MIXER ALIGNMENT 13 14. 15. 16. 17 18. 19. Connect the synchronized sweep voltage from the sweep generator to the horizontal input of the oscilloscope for horizontal deflection. The generator output lead should be terminated with its characteristic impedance, usually 50 ohms. Connect a 330O resistor from Collector of Mixer to chassis. Replace cover. Use only enough sweep generator output to provide a usable pattern on scope. Use 10MC sweep unless otherwise noted. Coils not containing adjustable cores are adjusted by expanding or compressing coil turns. DUMMY ANTENNA Two 120C Carbon Resistors 11 SWEEP GENERATOR COUPLING Across antenna termi- nals with 120S2 in each lead. 11 11 SWEEP GENERATOR FREQUENCY 213 MC 177MC 85MC Not used MARKER GENERATOR FREQUENCY 211. 25MC 215.75MC 213 MC 210 MC 216MC 177MC 87. 75MC B3.25MC 43. SMC (400% 30% AM Mod) CHANNEL 13 7 6 11 4 CONNECT SCOPE Vert. Amp. thru special Detector jig (Fig. 204) to point . Low side to chassis. Across Video Det. load ADJUST A213 A214, A215 A216 A217, A218 A219, A220 A221 A222 REMARKS Adjust for maximum gain and symmetry of response similar to Fig. 201. with markers as shown. If necessary, adjust by expanding or com- pressing coil turns for maximum sym- metrical response centered about 113MC. marker. Adjust spacing between gimmick wires (A216) for proper bandwidth as in Fig. 201 Adjust to obtain correct tilt on top of curve as in Fig. 203 to compensate for the tuning effect of channel 13. Repeat step 14, retouch only SLIGHTLY. Repeat step 16. Adjust for approximate correct bandwidth with sound carrier between 50 and 70% as in Fig. 202. Adjust for maximum gain at 83. 25MC marker. Repeat step 17 adjust A219 and A220 only SLIGHTLY. Remove 330S resistor. Adjust for MINIMUM 400% indication on scope. Cettor Freq/-Actu lC iy Desired 00 2 58 3 O So D9 Actual Desired- Center Freq. 177MC v INPUT COMPENSATED ORIGINAL 2. 2mmf1N60 OUTPUT 330mmf o 5 m 70 FIG. 203 SET 475 F IG.204 FOLDER 2 (BUILD IN SHIELDED CASE) PAGE 7 RadioFans.CN TUNER PARTS LIST AND DESCRIPTIONS 76-11773(1110) TRANSISTORS ITEM No. X201 X202 X203 PHILCO PART NO. 34-6000-25 34-6000-26 34-6000-27 USE RF Amp. (T1561) Mixer (T1600) Oacillator (T1597) REPLACEMENT DATA CBS PART No. RCA PART No. RAYTHEON PART No. SYLVANIA PART No. NOTES PNP PNP PNP FIXED Capacity values given in th Includes clamp assembly. KJ n 00 O K do So TRANSFORMER (DRIVER) ITEM No. T6 TURNS RATIO PRI. 1 SEC. 1 REPLACEMENT DATA PHILCO PART No. 32-8916-1 PART No. Merit PART No. Stoncor PART No. Thordorson PART No. Triod PART No. NOTES TRANSFORMER (AUDIO OUTPUT) ITEM No. T7 IMPEDANCE PRI. 70n CT SEC. 3.2n REPLACEMENT DATA PHILCO PART No. 32-8908-1 PART No. Merit PART No.PART No.PART No.PART No. Triod PART No. NOTES SPEAKER ITEM No. SP1 TYPE SIZE 3i FIELD PM V. C. IMP. 3-4n REPLACEMENT DATA PHILCO PART No. 36-1652-5 GUAM PART No. 3A07 NOTES RECTIFIERS ITEM No. Ml M2 M3 M4 M5 RATING CURRENT (Measured) .620A . 620A .001A .040A .010A REPLACEMENT DATA PHILCO PART No. 34-8048-3 34-8048-3 34-8050-3 34-8050-7 34-8050-2 INTERNATIONAL PART No. SD500 SD500 SD500 SD500 SD500 ITT PART No. HAS 04 HAS 04 HA504 HA504 HA504 SARKES TARZIAN PART No. 10H 10H F-2 F-2 F-2 SYLVANIA PART No. SR500 SR500 SR200 SR200 SR200 NOTES Silicon Type Silicon Type Silicon Type Silicon Type Silicon Type O o m TO PAGE 11 RadioFans.CN PARTS LIST AND DESCRIPTIONS (Continued) FUSES ITEM No. M6 TYPE 3AG RATING 1. 6A 125V S/B P/T REPLACEMENT DATA PHILCO PART No. FUSE 45-2656-23 HOLDER LITTELFUSE PART No. FUSE 31501.6 (SAG 1. 6A 125V S/B P/T) HOLDER BUSS PART No. FUSE MDV 1 6/10 HOLDER BATTERIES ITEM No. M7 VOLTAGE 7iv PHILCO PART No. 41-8066 REPLACEMENT DATA BURGESS AB EVEREADY AB 560 MALLORY AB NOTES CRYSTAL DIODES No. M8 M9 M10 Mil M12 M13 M14 ORIG. TYPE 1N60A 1N60A 1N60A 1N60A 1N60A 1N60A 1N91 REPLACEMENT DATA PHILCO PART No. 34-8022-3 34-8022-3 34-8022-3 34-8022-3 34-8022-3 34-8022-3 34-8051 CBS PART No. 1N60 1N60 1N60 1N60 1N60 1N60 RAYTHEON PART No. 1N60 1N60 IN60 1N60 1N60 1N60 SYLVANIA PART No. 1N60 1N60 1N60 1N60 1N60 1N60 NOTES Video Detector (Pigtail) FM Discriminator (Pigtail) FM Discriminator (Pigtail) Phase Detector (Pigtail) Phase Detector (Pigtail) Noise Switch (Pigtail) Horiz. Damper (Pigtail) MISCELLANEOUS ITEM No. M15 M16 M17 M18 M19 PART NAME Tuner Switch Switch Magnet Antenna Printed Board Printed Board Printed Board PHILCO PART No. 76-11773 42-2116-2 42-2113-1 76-10970-1 54-6992 54-6991 54-6990 NOTES VHF (T-110) Function (AC-Battery-Charge) Range (Fringe, Normal, Strong) Beam Aligning JFD Replacement Part #TA390 Video, IF, Sync, Sound Deflection Vert. Output CABINETS & CABINET PARTS (When Ordering Cabinets & Cabinet Parts, Specify Model, Chassis & Color) NAME Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Beam Splitter Mirror Lid Lid Mask Housing Tilt Mechanism Cabinet Cabinet Cabinet Top Cabinet Top Handle Assembly Handle Assembly PART NO. 28-11353-2 28-11353-4 54-5577-1 54-6265-48 54-6265-51 54-5638-1 54-5638-2 54-6265-49 54-6265-52 54-6265-50 54-6265-53 54-5575 54-5576 54-5570-1 54-5570-2 28-13111 54-5568-1 76-11788 54-5575-3 54-5574-4 54-5569-1 54-5569-2 76-11805-1 76-11805-2 DESCRIPTION Channel Selector, Model H-2010L Channel Selector, Model H-2010BL Fine Tuning Off-On-Volume, Brightness, Contrast, Vert. Hold, Model H2010L Olf-On-Volume, Brightness, Contrast, Vert. Hold, Model H2010BL Function, Model H2010L Function, Model H2010BL Range, Model H2010L Range, Model H2010BL Time Indicator, Model H2010L Time Indicator, Model H2010BL Part of Optical System Part of Optical System Visor, Part of Optical System, Model H2010L Visor, Part of Optical System, Model H2010BL Part of Optical System Part of Optical System Part of Optical System Model H2010L Model H2010BL Brown, Model H2010L, H2010BL Black, Models H2010L, H2010BL Model H2010L Model H2010BL WIRING DATA High Voltage Lead Use BELDEN No. 8869 Shielded Hook-up Wire Use BELDEN No. 8885 (Single Conductor) 8738 (Two Conductor) General-use Unshielded Hook-up Wire Use BELDEN No. 8530 (Solid) Available in Ten Colors 8524 (Stranded) Available in Ten Colors Power Cord (Interlock Type) Use BELDEN No. 8874 300J2 Tuner Input Lead Use BELDEN No. 8225 300S2 Antenna Lead-in Use BELDEN No. 8230 or 8275 Antenna Rotor Cable Use BELDEN No. 8464 (Flat) or 8484 (Round) - 4 Conductor 8485 (Round) - 5 Conductor 8488 (Round) - 8 Conductor PAGE 12 RadioFans.CN PHILCO MODELS H2O1OBL, H2OlOL(Ch. 1OAT1O) FOLDER 2 M3IA WOXJLO9 (OIIL) eU!l-9JL H3NHX RadioFans.CN o MIXER (SJ3)MIXER COLUCTOR COIL felf) VTi/ C JL JT JSPa.JViVW IIF OUTPUT -RFAGC A PHOTOFACT STANDARD NOTATION SCHEMATIC Howard W. Sami & Co., Inc. 1960 VHF TUNER 76-11773 (T110) RadioFans.CN HORIZOSC BASE HORIZOSC STABCOIL(C22 SWEEP PRINTED BOARD - CAPACITOR & MISC IDENT TOP TP4 VIDEO IF BIAS 1st VIDEO BASE VIDEO, SOUND, SYNC PRINTED BOARD - ALIGNMENT & INDUCTOR IDENT PAGE 15 RadioFans.CN A Howard W. SamsClRCUITRACEPhoto 144 VERT OUTPUT PRINTED BOARD R98) R49HT5 (R48MC2 CHASSIS - RESISTOR, INDUCTOR, TRANSFORMER & MISC IDENT PAGE 16 RadioFans.CN CircuiTrace Numbers 49 thru 91 o n o o i 3s o o OB A Howard W. SamsCIRCUITRACEPhoto VIDEO, SOUND, SYNC PRINTED BOARD O r- O m JO to PAGE 17 RadioFans.CN o O m 00 VIDEO, SOUND, SYNC PRINTED BOARD - RESISTOR & TRANSFORMER IDENT RadioFans.CN SWEEP PRINTED BOARD - RESISTOR & INDUCTOR IDENT i aacnoj (OilVOL -M3) 101OSH 18010SH S13QOW ODIIHd RadioFans.CN HEIGHTVERT LINEARITY AUX VERT LINEARITY JL CENTERINGAC ,BAT CHG * FOCUS POINTS AUX HORIZ HOLD DRIVE LEVEL CABINET-REAR VIEW HORIZONTAL SWEEP CIRCUIT ADJUSTMENTS Connect a clip lead from TP-1 to TP-2. Connect a clip lead from TP-5 to chassis. With a station signal tuned in, set Horizontal Hold to center of its range. Adjust the Aux. Horizontal Hold (R6C) to correct line fre- quency (the picture will not be stable). Remove the clip lead from TP-1 an