Denon-DRAF107-rec-sm维修电路原理图.pdf

D&M Holdings lnc.eVer. 5SERVICE MANUALAM-FM STEREO RECEIVERMODELJPE3E2EKE2AE1CE1KEUTDRA-F107? ?DRA-F107DAB? ?For purposes of improvement, specifications and design are subject to change without notice.Please use this service manual with referring to the operating instructions without fail.Some illustrations using in this service manual are slightly different from the actual set.Please refer to theMODIFICATION NOTICE.S0089-1V05DM/DG1007RadioFans.CN 收音机爱 好者资料库2DRA-F107 / DRA-F107DABPlease heed the points listed below during servicing and inspection.Heed the cautions!Spots requiring particular attention when servicing, suchas the cabinet, parts, chassis, etc., have cautions indicatedon labels or seals. Be sure to heed these cautions and thecautions indicated in the handling instructions.Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching in-ternal metal parts when the set is energized couldcause electric shock. Take care to avoid electric shock,by for example using an isolating transformer andgloves when servicing while the set is energized, un-plugging the power cord when replacing parts, etc.(2)There are high voltage parts inside. Handle with extracare when the set is energized.Caution concerning disassembly andassembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if fingers aremoved across them. Use gloves to protect your hands.Only use designated parts!The sets parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In par-ticular, for the important safety parts that are marked z onwiring diagrams and parts lists, be sure to use the desig-nated parts.Be sure to mount parts and arrangethe wires as they were originally!For safety reasons, some parts use tape, tubes or other in-sulating materials, and some parts are mounted away fromthe surface of printed circuit boards. Care is also taken withthe positions of the wires inside and clamps are used tokeep wires away from heating and high voltage parts, sobe sure to set everything back as it was originally.Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected for servicing have been put back in their original po-sitions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insu-lation check on the external metal connectors and betweenthe blades of the power plug, and otherwise check thatsafety is ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnectthe antenna, plugs, etc., and turn the power switch on. Us-ing a 500V insulation resistance tester, check that the in-sulation resistance between the terminals of the powerplug and the externally exposed metal parts (antenna ter-minal, headphones terminal, microphone terminal, inputterminal, etc.) is 1M or greater. If it is less, the set mustbe inspected and repaired.Concerning important safetypartsMany of the electric and structural parts used in the sethave special safety properties. In most cases these prop-erties are difficult to distinguish by sight, and using re-placement parts with higher ratings (rated power andwithstand voltage) does not necessarily guarantee thatsafety performance will be preserved. Parts with safetyproperties are indicated as shown below on the wiring dia-grams and parts lists is this service manual. Be sure to re-place them with parts with the designated part number.(1) Schematic diagrams . Indicated by the z mark.(2) Parts lists . Indicated by the z mark.Using parts other than the designatedparts could result in electric shock, fires orother dangerous situations.SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of thepower cord is less than 460 kohms, the unit is defective.CAUTIONCAUTIONRadioFans.CN 收音机爱 好者资料库3DRA-F107 / DRA-F107DABDIMENSION4DRA-F107 / DRA-F107DABWIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as they were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noise generation.Wire arrangement viewed from the topFront Panel sideBack Panel side5DRA-F107 / DRA-F107DABDISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-assembling, assemble it in order of the reverse of the following flow.TOP COVERFRONT PANEL ASSYAMP PCBREAR PANELRefer to EXPLODED VIEWRefer to EXPLODED VIEWRefer to EXPLODED VIEWFRONT PCBAMP PCBREAR PANEL (Ref. No. of EXPLODED VIEW : C2) (Ref. No. of EXPLODED VIEW : C7) (Ref. No. of EXPLODED VIEW : M14)SMPS PCBMAIN PCBRefer to EXPLODED VIEWUPDATE PCBRefer to EXPLODED VIEWSMPS PCBRefer to EXPLODED VIEWMAIN PCB (Ref. No. of EXPLODED VIEW : C3)UPDATE PCB (Ref. No. of EXPLODED VIEW : C8) (Ref. No. of EXPLODED VIEW : C13)POWER PCBRefer to EXPLODED VIEWTUNER PACKPOWER PCBRefer to EXPLODED VIEW (Ref. No. of EXPLODED VIEW : C6)TUNER PACK (Ref. No. of EXPLODED VIEW : C12)PHONO PCBRefer to EXPLODED VIEWPHONO PCB (Ref. No. of EXPLODED VIEW : C11)DAB PCBRefer to EXPLODED VIEWDAB PCB (Ref. No. of EXPLODED VIEW : C9Please refer to EXPLODED VIEW for the disassembly method of each PCB.6DRA-F107 / DRA-F107DABCAUTION IN SERVICINGInitializing DRA-F107/DRA-F107DABDRA-F107/DRA-F107DAB initialization should be performed when the com, and peripheral parts of com are replaced.1. Switch off the unit and remove the AC cord from the wall outlet.2. Hold the following the 0 button and the AUTO PRESET button, and plug the AC cord into the outlet. dNote: All user settings will be lost and this factory setting will be recovered when this initialization mode.So make sure to m+emorize your setting for restoring after the initialization.7DRA-F107 / DRA-F107DABSPECIAL MODECD TEST MODENoButton nameFunctionDisplayS1Version No. Display ModeS1.1 Plug AC cord into power outlet while pressingthe ON/STANDBY button and the SDB/TONE button same time on Main Unit.The Version number of MPU is displayed.MUTING ONUnplug AC cord to clear this mode. *: The version number of Main MPUS1Version No. Display ModeS1.2When the iPod Dock is connected Plug AC cord into power outlet while pressingthe ON/STANDBY button and the SDB/TONE button same time on Main Unit.The Version number of MPU is displayed.MUTING ONUnplug AC cord to clear this mode. *: The version number of MPU+: The version number of iPod DockS2VFD checking mode Plug AC cord into power outlet while pressingthe ON/STANDBY button and the AUTOPRESET button same time on Main Unit.All segment of FLD is turning on and off everyone second . MUTING ON.Unplug AC cord to clear this mode. All segment turn on and off. S3EEPROM testing ModePlug AC cord into power outlet while pressingthe ON/STANDBY button and the TUNERbutton same time on Main Unit.ON / STANDBY LED lighted ORANGE (Thetest is started). MUTING ON.When power LED lighted Green, thisEEPROM test was OK.When power LED lighted RED, this EEPROMtest was NG.Unplug AC cord to clear this mode.S4Cold start mode(Initialization)Plug AC cord into power outlet while pressingthe AUTO PRESET button and the 0 buttonsame time on Main Unit.The system is reset.- source: CD/USB- SDB: OFF- BASS: 0- TREBLE: 0- BALANCE: CENTER- DIMMER: 100%- VOLUME: 0- Preset Frequency of TUNER:All 0- Main Unit 0/1 button:-/+ button for PRESET- CLOCK: 00:00(Flashing):AM12:00(Flashing)(E3)- TIMER(EVERYDAY/ONCE):Timer Function: CDTimer start time: 0:00 (AM12:00 : E3)Timer stop time: 0:00 (AM12:00 : E3)The system is reset, and once this is com-pleted the unit is set to the normal mode.DRAVERDDOCKRAVERVER+8DRA-F107 / DRA-F107DABTROUBLE SHOOTING1. FLD dosent lightCheck FuseCheck if there is any leak or short-circuiting SMPS BDN.Gon rectifier circuit of SMPS BD? F901 OK?Check Parts? Q903,IC93,IC92,DB91 on SMPS BDO.K.Check Power Supply Voltages for System uCOM.MAIN BD MCU,Function Bloc?N.GCheck Soldering.? BN96:1pin ST+6V? BN96:1? D607:Cathode? SUB TRANS BD? IC65:3pin +3.3VO.K.Check Reset signal for System uCOM.MAIN BD MCU,Function Bloc?N.GCheck Soldering.? IC62:10pin RESET? IC66 on MAIN BD Hlevel O.K.? (2.8V)O.K.Check Oscillation waveform.MAIN BD MCU,Function Bloc?N.GCheck Soldering.? IC62:11pin? X202 on Main BD14.7456MHz OK?O.K.Check Power 50/60 SignalMAIN BD MCU,Function Bloc?N.GCheck Soldering.? IC62:19pin 50/60? BN96: 2pinPulse OK? SUB TRANS BDO.K.Check Power Supply Voltages for FLDCheck Soldering.FRONT BD? FRONT BD BN83:3pin +VKK? FL81:38pin VH (42V)? FRONT BD BN83:4pin ,5pin F_AC? FL81:37pin VDD (3.3V)? FRONT BD WF81:1pin SW+3.3V? FL81: 1pin F1,43pin F2 (AC3.3V)N.G? SMPS BDCN93 3pin VKK? SMPS BD,CN93 4pin FL+- 5pin FL-? MAIN BDWN81 1pin SW+3.3VCheck Parts? SMPS BD Q933,Q934, IC97,D945, D935IC94, D950 ,D933O.K.Check Reset Signal for FLDCheck Soldering.FRONT BDN.G? FRONT BD WF81:5pin VFD_RST1? FL81:35pin /RST? MAIN BD WN81:5pin VFD_RST1Hlevel O.K.? (3.3V)? IC62:2pin FL_RST on MAIN BDO.K.Check FLD Dirive Signal for FLDCheck Soldering.FRONT BDN.G? WF81: 2,3,4pin on FRONT BD? FL81:32,33,34pin DA,CP,CS VFD_DI,VFD_CLK,VFD_CE? WN81: 2,3,4pin on MAIN BDVFD_DI,VFD_CLK,VFD_CE? IC62 on MAIN BDEND9DRA-F107 / DRA-F107DAB2. POWER OFF with Blinking POWER LEDCheck Power Supply Voltages for Analog BlockCheck Soldering.MAIN BD MCU,Function Bloc?N.G? IC22,23 on MAIN BD? ?IC21?:31pin AVCC+7V? ?BN61?:1pin,2pin 12V on MAIN BD 67pin AVCC-7V? ?CN92?1pin,2pin 12V on SMPS BD? SMPS BD IC97,IC98,D945,D931O.K.Check Power Supply Voltages for Digital BlockCheck Soldering.MAIN BD MCU,Function Bloc?N.GMAIN BD MCU,Function Bloc? ?IC64?:3pin ?3.3V? IC64? ?WC52?:3pin HB+? ?BN61?:4pin SW5.6V? ?WC52?:3pin 27VAD.POWER AMP BD?WP52?:3pin 27VA?CN91?:1,2,3,7pin 27VASMPS BD?BN91?:1,2,3,7pin 27VAD931O.K.Check Protect Signal for System uCOM.Check Soldering.MAIN BD MCU,Function Bloc?N.GMAIN BD MCU,Function Bloc? IC62:71pin PROT_2 High Level OK? D371,D373,D374O.K.Check Protect Signal for D.Power AmpCheck Soldering.D.POWER AMP BDN.GD.POWER AMP BD? ?IC53?:3pin 12V? IC54? ?IC54?:17pin SD,18pin OTW,19 pin READY? IC53 High Level OK? IC54,IC53? D.Power Amp Heat SinkO.K.Check Control Singal for DC ProtectCheck Soldering.? Q573_B Low Level OK?MAIN BD MCU? Q571,572,573,574? D571,572N.GCheck Parts? Q571,572,573,574? D571,572O.K.Check Protect Signal for System uCOM.Check Soldering.MAIN BD MCU,Function Bloc?N.GMAIN BD MCU? IC62:74pin PROT_1 High Level OK? D570D.POWER AMP BD? D504,D505,D506END10DRA-F107 / DRA-F107DAB3. System Connector(DENON BUS) dont workCheck Power Supply Voltages for DENON BUSCheck Soldering.INPUT BD DENON BUS BLOCKN.GINPUT BD DENON BUS BLOCK? WF31?:13pin ST5V? WF31?:13pin ST5VMAIN BD? WN31?:13pin ST5V? Q613? ?BN96?:1pin ST6V? D607? SUB TRANS BDO.K.Check Control Signal for DENON BUSCheck Soldering.INPUT BD DENON BUS BLOCKN.GINPUT BD DENON BUS BLOCK? WF31?:9pin BUS CLK,10pin BUS RXD_O? JK31 11pin BUS TXD_O OK? Q301,Q302? WF31 9,10,11pinMAIN BDWN31 9,10,11pinIC31IC21:26,27,28 pinO.K.END4. The Key Operation dont workCheck Signal for KEYCheck Soldering.MAIN BDN.G? WF81,S801?S809,VR81,VR82 on FRONT BD? IC623,5pin F_JOG,21,22 VJOG? WN81,IC62 in MAIN BD?17pin PWR_KEY,93,95pin Key 0/1 OK?O.K.END5. The Remote Control Operation dont workCheck Signal for Remote ControlCheck Soldering.? ?IC62?:73pin REMOTE on MAIN BDN.G? WF81on FRONT BD? ?RC81?:3pin Vcc 3.3V OK? WN81,IC62 in MAIN BDO.K.END11DRA-F107 / DRA-F107DAB6. No Sound,Noise generated(1)CD/USB PLAY inCheck Analog Audio Data input for FUNCTION ICMAIN BD MCU,Function Bloc?N.GCheck Soldering.? IC21 input 78,79pin ? IC21 on MAIN BD CD_L,CD_R? JK21O.K.Check Power Supply Voltages for PREAMP & POWER AMP.Check Soldering.MAIN BD MCU,Function BlockN.G? BN61:1,2pin +12V,-12V,? BN61:1,2,4pin+12V,-12V , SW+5.6V 4pin SW+5.6V on MAIN BD?D.POWER AMP BD? CN91:1,2,3,7pin +27Von D.AMP BLOCK? WP51:5pin +12V? ?WP51?:5pin +12V? CN91 : 1,2,3,7pin +27V? SMPS BD IC97,IC98,D945,D931? IC53: 3pin +12V? SMPS BD IC91,D951? D.POWER AMP BD IC53O.K.Check Power Supply Voltages for FUNCTION ICCheck Soldering.MAIN BD MCU,Function Bloc?N.G? IC22,IC23 on MAIN BD? IC21:30pin VDD (3.3V)? IC64 on MAIN BD 31pin AVCC+7V,67pin AVCC-7VO.K.Check Control Signal for FUNCTION ICCheck Soldering.MAIN BD MCU,Function Bloc?N.G? IC62 on MAIN BD? IC21:27,28,29pinCLK,DATA,LATCHO.K.Check Analog Audio Data output from FUNCTION &Check Soldering.PRE AMPN.G? IC21 on MAIN BDMAIN BD MCU,Function Bloc? IC24 on MAIN BD? IC21:44, 39pin Lout,Rout? IC24:1,7 pinO.K.Check Audio function Mute Signal.Check Soldering.MAIN BD MCU,Function Bloc?N.G? Q603,604, on MAIN BDQ103,104:Llevel O.K.? (-12V)? IC62 on MAIN BDO.K.Check Analog Audio Data input for POWER AMPCheck Soldering.D.AMP BD N.G? WC51 1,3pin on MAIN BD,? IC54: 6,7pin IN_A,IN_B VOL_L_OUT,VOL_R_OUT 12,13pin IN_C, IN_D? ?WP51?:1,3pin on D.Power BD? IC51,IC52 on D.AMP BDO.K.Check SPEAKER RELAY control SignalCheck Soldering.MAIN BDN.G? Q570,Q575 on MAIN BD? D573:ANODE Llevel O.K.? (-12V)? IC62 77pin RL_MUTE on MAIN BDO.K.12DRA-F107 / DRA-F107DABCheck Analog Audio Data output for POWER AMPCheck Soldering.to SPEAKER. ? WP52 on D.AMP BLOCKD.POWER AMP BLOCKN.G? IC54 on D.AMP BLOCK? IC54:39,40pin OUT_A , 36pin OUT_B? WC52 on MAIN BD 31pin OUT_C , 27,28pin OUT_DMAIN BD SP OUT BLOCK? JK51O.K.END(2) AM/FM TUNER-inCheck Power Supply Voltages for AM/FM TUNER.Check Soldering.MAIN BDN.G? D931 on SMPS BD? Q813, 611 on MAIN BD? ?IC62?:59pin TU_PWRO.K.Check Control Signal for AM/FM TUNER.Check Soldering.MAIN BDN.GMAIN BD? WN21: 7pin PLL_CE,8pin R/F_DATA? IC61,62,WN21 9pin RF_CLK,10pinPLL_DI OK?O.K.Check Analog Audio Data output from TUNER PACKCheck Soldering.MAIN BDN.G? WN21 1,3 pin TU_L,TU_R on MAIN BD? TUNER PACK output ? WN 21:1,3pin TU_L, TU_R? IC21:68,69pin?TU_L,TU_RO.K. to CD/USB in ?Mark(3) Portable-in(Front-in)Check Analog Audio Data output from Prtable-inFRONT BDN.GCheck Soldering.? Portable-in output ? JK82,on FRONT BD? BN82 1,3pin POR_L.POR_R? BN82 on FRONT BDO.K.Check Analog Audio Data input for FUNCTION ICCheck Soldering.MAIN BD MCU,Function Bloc?N.G? CN82:1,3pin PORT_LPORT_R on MAIN BD? IC21 input 2,3pin ? WP11:10,12pin on MAIN BD POR_L.POR_R? WC11:10,12pin on MAIN BD? IC21:2,3pin PORT_L,PORT_RO.K. to CD/USB in ?Mark13DRA-F107 / DRA-F107DAB(4) DAB TUNER-inCheck Power Supply Voltages for DAB TUNER UNIT.Check Soldering.INPUT BD DAB BLOCKN.G? ?WP82?:1pin DAB_PWR? ?WP82?:5pin 5VDD 5pin SW+5V on INPUT BD? ?CN71?:2pin 3.3V? IC71,72 on INPUT BD? ?CN71?:1pin 1.5V? ?WC61?:1pin DAB_PWR 5pin 5VDD on MAIN BD? ?BN61?:5pin 5VDD on MAIN BD? D931 on POWER BD? ?IC62?:53pin DAB_PWRCheck Parts? IC71,72 on INPUT BDO.K.Check C