Yamaha-RXE410-cs-sm(1) 维修电路原理图.pdf

SERVICE MANUALI CONTENTSTO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . . . .2SYSTEM COMPOSITION . . . . . . . . . . . . . . . . . . . . . .3FRONT PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . .46REMOTE CONTROL PANELS . . . . . . . . . . . . . . . . . .6SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .7INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8DISASSEMBLY PROCEDURES . . . . . . . . . . . . . . . . .8SELF DIAGNOSIS FUNCTION (DIAG) . . . . . . . . .915AMP ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . .16DISPLAY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1822BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . .2324PRINTED CIRCUIT BOARDS . . . . . . . . . . . . . . .2531PIN CONNECTION DIAGRAMS . . . . . . . . . . . . . . . .32SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . .3337REPLACEMENT PARTS LIST . . . . . . . . . . . . . .3948REMOTE CONTROLS . . . . . . . . . . . . . . . . . . . . .4950SYSTEM CONTROL . . . . . . . . . . . . . . . . . . . . . .5158SERVICE MANUALThe MCR-E810 is composed of the RX-E810, NX-E800 and DVD-E810.The MCR-E410 is composed of the RX-E410, NX-E800 and CDX-E410.This service manual is for the RX-E810, RX-E410 and NX-E800.For service manual of the DVD-E810 and CDX-E410, please refer to the following publication number:DVD-E810 101017CDX-E410 101018101019IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, arealready known and understood by the users, and have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in per-sonal injury, destruction of expensive components, and failure of the product to perform as specified. Forthese reasons, we advise all YAMAHA product owners that any service required should be performed byan authorized YAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certifica-tion or recognition of any applicable technical capabilities, or establish a principle-agent relationship ofany form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering,and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore,inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear toexist, please contact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to thisbuss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power tothe unit.RX-E810/RX-E410/NX-E800 2006 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically without permission.P.O.Box 1, Hamamatsu, Japan 06.07RX-E810/RX-E410/NX-E800MICRO COMPONENT SYSTEM MCR-E810/MCR-E410RadioFans.CN 收音机爱 好者资料库RX-E810/RX-E410/NX-E8002RX-E810/RX-E410/NX-E800I TO SERVICE PERSONNEL1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohms shuntedby 0.15F.WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!The solder used in the manufacturing process except soldering of the P.C.B. assy contains LEAD. In addition, otherelectrical/electronic and /or plastic (where applicable) components may also contain traces of chemicals found by theCalifornia Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductiveharm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-SON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands beforehandling food.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in both polarities.“CAUTION”“F1, F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 3.5A,125V FUSE.”CAUTIONF1, F2: REPLACE WITH SAME TYPE 3.5A, 125V FUSE.ATTENTIONF1, F2: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 3.5A, 125V.About Lead Free SolderThe P.C.B.s installed in main unit are soldered using the all lead free solder.Among some types of lead free solder currently available, it is recommended to use one of the following types for the repairwork. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the leadsolder, be sure to use a soldering iron suitable to each solder.RadioFans.CN 收音机爱 好者资料库RX-E810/RX-E410/NX-E8003RX-E810/RX-E410/NX-E800I SYSTEM COMPOSITIONThe MCR-E810 consists of the DVD-E810, RX-E810 and NX-E800.The MCR-E410 consists of the CDX-E410, RX-E410 and NX-E800.MCR-E810 (U, C, T, K, A, B, G, L, V models)DVD-E810RX-E810NX-E800 x 2CDX-E410RX-E410NX-E800 x 2MCR-E410 (B, G models)RX-E810/RX-E410/NX-E8004RX-E810/RX-E410/NX-E800RX-E410 (B, G models)NX-E800 (U, C, T, K, A, B, G, L, V models)I FRONT PANELSI REAR PANELSRX-E810 (T model)RX-E810 (U, C models)RX-E810 (A model)RX-E810 (K model)RX-E810 (U, C, T, K, A, B, G, L, V models)RX-E810/RX-E410/NX-E8005RX-E810/RX-E410/NX-E800RX-E810 (V model)RX-E810 (L model)RX-E810 (G model)RX-E810 (B model)RX-E410 (B model)RX-E410 (G model)RX-E810/RX-E410/NX-E8006RX-E810/RX-E410/NX-E800I REMOTE CONTROL PANELSNX-E800RX-E810(U, C, T, K, A, L, V models)RX-E810(B, G models)RX-E410(B, G models)7RX-E810/RX-E410/NX-E800I AUDIO SECTIONMinimum RMS Output Power (Power Amp. section)20 Hz to 20 kHz, 0.1 % THD, 6 ohms. 40 W + 40 W1 kHz, 0.1 % THD, 6 ohms . 55 W + 55 WDynamic Power Per Channel (IHF)6 ohms . 60 W + 60 W4 ohms . 75 W + 75 W2 ohms . 100 W + 100WMax Power Per Channel (B, G models)1 kHz, 0.7 % THD, 4 ohms . 60 W + 60 WIEC Power (B, G models)1 kHz, 0.04 % THD, 6 ohms . 55 W + 55 WMaximum Useful Output Power (JEITA) (L, V models)1 kHz, 10 % THD, 6 ohms (L, V models). 65 WPower Band Width (0.1 % THD, 30 W, 6 ohms)FRONT L/R. 10 Hz to 50 kHzDamping Factor20 Hz to 20 kHz, 6 ohms . 60 or moreInput Sensitivity/Input ImpedanceRX-E810DVD, etc. .150 mV / 47 k-ohmsRX-E410CD, etc.150 mV / 47 k-ohmsMaximum Input Voltage (1 kHz, 0.5 % THD)RX-E810DVD, etc. . 3.0 V or moreRX-E410CD, etc. 3.0 V or moreRated Output Voltage/Output ImpedanceSUBWOOFER .2.0 V / 680 ohmsREC OUT .150 mV / 1.2 k-ohms or lessHeadphone Jack Rated Output/ImpedanceRX-E810DVD, etc. (1 kHz, 150 mV, 8 ohms) .0.23 V / 120 ohmsRX-E410CD, etc. (1 kHz, 150 mV, 8 ohms) .0.23 V / 120 ohmsFrequency Response (20 Hz to 20 kHz)RX-E810DVD, etc. .0 0.5 dBRX-E410CD, etc.0 0.5 dBTotal Harmonic Distortion (20 Hz to 20 kHz, 30 W/6 ohms)RX-E810DVD, etc. to SP OUT . 0.04 % or lessRX-E410CD, etc. to SP OUT. 0.04 % or lessSignal to Noise Ratio (IHF-A Network)RX-E810DVD, etc., Input shorted (150 mV) . 93 dB or more(250 mV). 98 dB or moreRX-E410CD, etc., Input shorted (150 mV) . 93 dB or more(250 mV) . 98 dB or moreResidual Noise (IHF-A Network)Pure direct on . 100 VI SPECIFICATIONSChannel SeparationRX-E810DVD, etc., Input 5.1 k-ohms shorted, 1 kHz / 10 kHz. 60 dB / 45 dB or moreRX-E410CD, etc., Input 5.1 k-ohms shorted, 1 kHz / 10 kHz.60 dB / 45 dB or moreTone Control CharacteristicsBASS: Boost/Cut . 10 dB (50 Hz)Turnover Frequency. 350 HzTREBLE : Boost/Cut . 10 dB (20 kHz)Turnover Frequency.3.5 kHzGain tracking error (0 to -60 dB) . 2 dB or lessI FM SECTIONTuning RangeU, C, L, V models. 87.5 to 107.9 MHzT, K, A, B, G, L, V models . 87.50 to 108.00 MHz50 dB Quieting Sensitivity (IHF) (1 kHz, 100 % MOD.)Mono . 2.8 V (20.2 dBf)Signal to Noise Ratio (IHF)Mono / Stereo . 73 dB / 70 dBHarmonic DistortionMono / Stereo (1 kHz). 0.5 % / 0.5%Antenna Input. 75 ohms unbalancedI AM SECTIONTuning RangeU, C, L, V models. 530 to 1710 kHzT, K, A, B, G, L, V models . 531 to 1611 kHzAntenna.Loop antennaI GENERALPower SupplyU, C models. AC 120 V, 60 HzT model. AC 220 V, 50 HzK model . AC 220 V, 60 HzA model . AC 240 V, 50 HzB, G models. AC 230 V, 50 HzL model . AC 220-240 V, 50/60 HzV model . AC 110-120 V, 50/60 HzPower ConsumptionU, C, V models . 115 WT, K, A, B, G, L models. 130 WStandby Power Consumption (Reference data). 0.1 WMaximum Power Consumption (V model)1 kHz, 6 ohms, 10 % THD . 300 WAC OutletsSwitched x 2U, C, T, G, L, V models . 100 W max. totalSwitched x 1A, B models . 100 W max. totalDimensions (W x H x D) . 215 x 108.2 x 362.5 mm(8-7/16 x 4-1/4 x 14-1/4)Weight . 5.7 kg (12 lbs. 9 oz)FinishRX-E810Gold color . T, A modelsBlack color . G modelSilver color . U, C, K, B, G, L, V modelsRX-E410Black color . G modelSilver color .B, G modelsAccessoriesRemote control x 1, Battery x 2, Indoor FM antenna x 1, AMloop antenna x 1, System control cable x 1I SPEAKER SECTION (NX-E800)Type. 2-way bass reflexMagnetic shielding typeDriverTweeter .2.5 cm (1) soft dome typeWoofer .13 cm (5-1/8) cone typeFrequency Response . 55 Hz to 28 kHz (-10 dB) to 80 kHz (-30 dB)Impedance . 6 ohmsRated Input . 60 WMaximum Input . 110 WSensitivity . 87 dB / 2.83 V/mCrossover Frequency .3 kHzInput Terminal .Screw/Banana typeDimensions (W x H x D) . 186 x 300 x 223 mm(7-5/16 x 11-13/16 x 8-3/4)Weight . 4.3 kg (9 lbs. 7 oz)FinishLight cherry/Silver color . U, C, A, B, G modelsBlack/High gloss piano color. U, C, T, K, A, B, G, L, V modelsAccessories . Speaker cable x 2* Specifications are subject to change without notice due to productimprovements.U . USA modelC . Canadian modelT . Chinese modelK . Korean modelA . Australian modelB . British modelG . European modelL . Singapore modelV . Taiwan model“iPod” is a trademark of Apple Computer, Inc., registered in theU.S. and other countries.DIMENSIONSUnit: mm (inch)215 (8-7/16)8.2 (5/16)100 (3-15/16)108.2 (4-1/4)21.8(7/8)15.6 (5/8)325.1 (12-13/16)362.5 (14-1/4)RX-E810/RX-E410/NX-E8008I INTERNAL VIEW? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?98724516312345678900I DISASSEMBLY PROCEDURESFig. 1Fig. 2(Remove parts in disassembly order as numbered.)1. Removal of Top Covera. Remove 4 screws (1) and 4 screws (2). (Fig. 1)b. Lift the top cover at the rear and move it rearward slantingly.(Fig. 1)Top coverHookHookFront panel unit43503112? ? ? ? ? ? ? ? ? ? ?2. Removal of Front Panela. Remove CB18, CB21, CB200, CB201 and CB209. (Fig. 2)b. Remove 2 screws (3), 2 screws (4) and 1 screw (5).(Fig. 1)c. Release 2 hooks and remove the front panel unit by pull-ing it forward. (Fig. 1)When checking the P.C.B.:a. Remove the top cover and the front panel unit.b. Remove 2 screws (6). (Fig. 3)c. Remove the OPERATION (2) P.C.B. which is con-nected directly to the lower P.C.B. with connections.d. Remove 6 screws (7). (Fig. 4)e. Remove 5 screws (8). (Fig. 4)f. Remove 2 screws (9). (Fig. 3)g. Remove 1 screw (0). (Fig. 1)h. Reinstall the OPERATION (2) P.C.B.i. Reinstall 2 screws (6). (Fig. 3)j. Remove the power transformer and MAIN P.C.B. (withthe rear panel attached) from the main chassis. (Fig. 5)Fig. 3Fig. 4Fig. 5? ? ?69Fig. 6? ?877? ? ? ? ? ? ? ? ? ?k. With the rear panel attached, set the MAIN P.C.B. on itsside.At this time, set the power transformer on its side aswell. (Fig. 5)l. Using a ground lead or the like, connect G2 and G4 ofthe MAIN P.C.B. with the rear panel. (Fig. 5)m.With the front panel unit set on its side, reconnect 5 con-nectors (CB18, CB21, CB200, CB201, CB209). ( Fig. 6)n. Connect the power cable, turn on the power and checkfor operation.RX-E810/RX-E410/NX-E8009RX-E810/RX-E410/NX-E800FIRMWARE VERSIONVFD CHECKFACTORY PRESETAD DATA CHECKiPod (DOCK)PROTECTION HISTORYERROR INFORMATIONMUTE CHECKPOWER OFF FACTORHISTORY1234567891.FIRMWARE VERSION / MODEL / DESTINATION2.CHECK SUM ALL1.Initial display2.VFD DISPLAY OFF3.VFD DISPLAY ALL4.VFD DIMMER5.CHECK PATTERN1.PRESET INHI (memory initialization inhibited)2.PRESET RSRV (memory initialized)1.PRT1/PRT22.PRT3/THM3.SYSTEM STATUS4.DESTINATION5.PANEL KEY (Key0/Key1)1.DOCK : OK/NG2.IP_PWR / IP_DET1.HISTORY 12.HISTORY 23.HISTORY 34.HISTORY 41.INDICATION2.RESET1.SP/HP OFF2.SP MUTE3.HP MUTE1.HISTORY 12.HISTORY 23.HISTORY 34.HISTORY 45.HISTORY 5I SELF DIAGNOSIS FUNCTION (DIAG)This unit has self diagnosis functions that are intended for inspection, measurement and location of faulty point.There are 9 DIAG menu items, each of which has sub-menu items.Listed in the table below are menu items and sub-menu items.No.MAIN MENUSUB MENURX-E810/RX-E410/NX-E80010RX-E810/RX-E410/NX-E800 Starting DIAGPress the “STANDBY/ON” key while simultaneously pressing those two keys of the main unit as indicated in the figurebelow. Starting DIAG in the protection cancel modeIf the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as describedbelow, and it will be possible to enter the DIAG mode. (The protection functions other than the excess current detect functionwill be disabled.)Press the “STANDBY/ON” key while simultaneously pressing those two keys indicated in the figure above. At this time, keeppressing those two keys for 3 seconds or longer.In this mode, the “SLEEP” segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with theprotection functions disabled.CAUTION!Using this product with the protection function disabled may cause damage to itself. Use special care for this point whenusing this mode.Keys of main unit Canceling DIAG1 Before canceling DIAG, execute setting for FACTORY PRESET of DIAG menu No.3 (Memory initialization inhibited orMemory initialized).*In order to keep the user memory stored, be sure to select PRESET INHIBITED (Memory initialization inhibited).2 Turn off the power by pressing the “STANDBY/ON” key of the main unit.Opening messageDIAG menu displayWhen there is no history of protection function:After a few secondsNO PROTECT BVER.B16 4BGVersion (1 alphabet)When there is no protection history Display provided when DIAG s