Aiwa-XRG4-cs-sm维修电路原理图.pdf

SERVICE MANUALDATACOMPACT DISCSTEREO SYSTEMBASIC TAPE MECHANISM : BZM-1 R1NMBASIC CD MECHANISM : BZG-5 ZD3NMXS-G3XS-G4XS-G5U,LH,EZ,KEZEZ,KS/M Code No. 09-013-441-5R1REVISIONSPEAKERSYSTEMCDCASSEIVERREMOTECONTROLLERXSG3(U,LH)RCBAS11CXG3SXG3RCBAS03XSG3(EZ,K)CXG3SXG3RCBAS11XSG4(EZ)CXG4SXG4RCBAS11XSG5(EZ)CXG5SXG5RCBAS03XSG5(K)CXG5SXG5 This Service Manual is the Revision Publishing and replaces Simple ManualXS-G3 (U,LH,EZ,K) / XS-G4 (EZ) / XS-G5 (EZ,K), (S/M Code No. 09-012-441-5T1). If requiring information about the CD mechanisim, see Service Manual of BZG-5,(S/M Code No. 09-00C-353-3N2)RadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONSTuning range87.5 MHz to 108 MHzUsable sensitivity (IHF)EZ,K: 16.8 dBfU,LH: 13.2 dBfAntenna terminal75 ohms (unbalanced)Tuning range531 kHz to 1602 kHz (9 kHz step)530 kHz to 1710 kHz (10 kHz step)Usable sensitivity350 V/mAntennaLoop antennaTuning range144 kHz to 290 kHzUsable sensitivity1400 V/mAntennaLoop antennaPower outputEZ,K:Rated: 40 W + 40 W (6 ohms,T.H.D. 1 %, 1 kHz/DIN45500)Reference: 50 W + 50 W (6 ohms,T.H.D. 10 %, 1 kHz/DIN45324)EZ:DIN MUSIC POWER: 121 W + 121 WU: 60 W + 60 W (50 Hz 20 kHz,T.H.D. less than 1 %, 6 ohms)75 W + 75 W (1 kHz, T.H.D. less than10 %, 6 ohms)LH:Rated: 60 W + 60 W (6 ohms,T.H.D. 1 %, 1 kHz)Reference: 75 W + 75 W (6 ohms,T.H.D. 10 %, 1 kHz)Total harmonic distortion EZ,K:0.08 % (25 W, 1 kHz, 6 ohms, DINAUDIO)U,LH:0.08 % (30 W, 1 kHz, 6 ohms, DINAUDIO)InputsVIDEO/AUX: 500 mVLH ONLY: MIC: 1.7mV (10 kohms)OutputSPEAKERS: 6 ohms or morePHONES: 32 ohms or moreTrack format4 tracks, 2 channels stereoFrequency response50 Hz 15000 HzRecording systemAC biasHeadsRecording/playback x 1, erase x 1LaserSemiconductor laser ( =780 nm)D/A converter1 bit dualSignal-to-noise ratio85 dB (1 kHz, 0 dB)Harmonic distortion0.05 % (1 kHz, 0 dB)Speaker system2 way, bass reflex (magnetic shielded)Speaker unitsWoofer: 140 mm coneTweeter: 60 mm coneImpedance6 ohmsDimensions (W x H x D)165 x 328 x 225 mmWeight3.5 kgSpeaker system2 way, bass reflex (magnetic shielded)Speaker unitsWoofer: 140 mm coneTweeter: 60 mm coneImpedance6 ohmsDimensions (W x H x D)170 x 328 x 268 mmWeight3.8 kgPower requirementsEZ,K: 230 V AC, 50 HzU: 120 V AC, 60 HzLH: 120 V / 220 230 V / 240 VAC(Switchable), 50 Hz / 60 HzPower consumptionU: 65 WLH: 85 WEZ: 70 WK: 78 WPower consumption With ECO mode on: 0.6 W in standby mode U,EZ,K: With ECO mode off: 17 WLH: With ECO mode off: 18 WDimensions of main unitU,EZ,K: 260 x 271.5 x 355 mm(W x H x D) (101/4 x 103/4 x 14 in.)LH: 260 x 271.5 x 364 mmDimensions (W x H x D)260 x 301 x 292 mmWeightU,EZ,K: 6.5 kg (14 lbs 5 oz)LH: 6.8 kg Design and specifications are subject to change without notice. The word BBEand the BBE symbol are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc.RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCTKLASSE 1LASER PRODUKTLUOKAN 1LASER LAITEKLASS 1LASER APPARATThis set employs laser. Therefore, be sure to follow carefullythe instructions below when servicing.WARNING!WHEN SERVICING, DO NOT APPROACH THE LASEREXIT WITH THE EYE TOO CLOSELY. IN CASE IT ISNECESSARY TO CONFIRM LASER BEAM EMISSION.BE SURE TO OBSERVE FROM A DISTANCE OF MORETHAN 30cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL PICK-UP BLOCK.sCaution: Invisible laser radiation whenopen and interlocks defeated avoidexposure to beam.sAdvarsel: Usynlig laserstling ved bning,nr sikkerhedsafbrydere er ude af funktion.Undg udsttelse for strling.VAROITUS!Laiteen Kyttminen muulla kuin tss kyttohjeessamainitulla tavalla saataa altistaa kyt-tjnturvallisuusluokan 1 ylittvlle nkymttmllelasersteilylle.VARNING!Om apparaten anvnds p annat stt n vad somspecificeras i denna bruksanvising, kan anvndarenutsttas fr osynling laserstrlning, som verskridergrnsen fr laserklass 1.PROTECTION OF EYES FROM LASER BEAM DURING SERVICINGCAUTIONUse of controls or adjustments or performance of proce-dures other than those specified herin may result inhazardous radiation exposure.ATTENTIONLutillisation de commandes, rglages ou procduresautres que ceux spcifis peut entraner une dangereuseexposition aux radiations.ADVARSELUsynlig laserstling ved bning, nr sikkerhedsafbrydereerude af funktion. Undg udsttelse for strling.This Compact Disc player is classified as a CLASS 1LASER product.The CLASS 1 LASER PRODUCT label is located on therear exterior.Precaution to replace Optical block(KSS-213F)Body or clothes electrostatic potential couldruin laser diode in the optical block. Be sureground body and workbench, and use care theclothes do not touch the diode.1) After the connection, remove solder shown inright figure.PICK-UP Assy PWBSolderRadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIRCharging voltage (V)Discharging Rated power (W)Parts number(C101, 102)resistor ()25-48100387-A00-247-09049-140220587-A00-232-090Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check thereference numbers of the charging capacitors on schematic diagram before starting the discharging work.2. Check items before exchanging the MICROCOMPUTERBe sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirmingthat the MICROCOMPUTER is surely defective.2-1. Regarding the HOLD terminal of the MICROCOMPUTERWhen the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLDterminal before exchange.When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has anyabnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.Good or no good judgement of the MICROCOMPUTER11111Turn on the AC main power.22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and theMICROCOMPUTER is judged to be good.1. Forced discharge of electrolytic capacitor of power supply blockWhen repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged acrossthe electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defectcan occur.In order to prevent the secondary trouble, perform the following measures before starting repair work.Discharge procedure11111Remove the AC power cord.22222Connect a discharging resistor at an end of lead wire thathas clips at both ends. Connect the other end of the leadwire to metal chassis.33333Contact the other end of the discharging resistor to thepositive (+) side (+VH) of C101. (For two seconds)44444Contact the same end of the discharging resistor as step33333 to the negative (-) side (-VH) of C102 in the same way.(For two seconds)55555Check that voltage across C101 and C102 has decreasedto 1 V or less using a multimeter or an oscilloscope.Select a discharging resistor referring to the following table.Fig-1MAIN C.BD101C101C1022234RadioFans.CN 收音机爱 好者资料库 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.2-2. Regarding resetThere are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC powercord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and toexchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or nogood of the MICROCOMPUTER.11111Remove the AC power cord.22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER isgood.Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change dependingon the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.2-3. Confirmation of soldering state of MICROCOMPUTERCheck the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange theMICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.Fig-2-2MICRO-COMPUTERMICROCOMPUTERFRONT C.BFRONT C.BVSSVDDC113*%C1131815Short with tweezers.RadioFans.CN 收音机爱 好者资料库 6 DISASSEMBLY INSTRUCTIONS1. DISASSEMBLY OF MECHANISM DECK ASSY 1) Remove the three screws. 2) Remove the three screws. 3) Remove the four screws (1) and remove the PANEL,TOP (2). 4) Remove the PANEL, RIGHT.RadioFans.CN 收音机爱 好者资料库 7 5) Remove the PANEL, LEFT. 6) Remove the six screws (1) and remove the CABI, REAR(2). 7) Remove the three FFCs (1), (2) (black) and (3), andremove the connector (4). 8) Remove the three screws (1) and remove the PWB,MAIN (2).RadioFans.CN 收音机爱 好者资料库 8 9) Slide up slightly the WINDOW, DISP ASSY (1).Insert a thin flathead screwdriver into the slide grooveand disengage the detents of the WINDOW, DISP ASSY(2) (in the left and right sides) and remove the WINDOW,DISP ASSY. 10) Remove the two FFCs (1) and (2), and the four screws(3) and remove the MECH DECK ASSSY (4). 11)Remove the two screws (1) and remove the HLDR,WINDOW (2).RadioFans.CN 收音机爱 好者资料库 9 12) Remove the four screws (1) and remove the BZM-1 (2).RadioFans.CN 收音机爱 好者资料库 10 2. INSTRUCTIONS FOR ASSEMBLING MECHANISMDECK ASSY 1) Install the BZM-1 and rotate the GEAR, RELAYclockwise until the BOX, CASS cannot move any more. 2) Install the HLDR, WINDOW so that the upper end of theHLDR, WINDOW and the upper end of the MECH ASSYcan be almost aligned to the same height. 3) Rotate the GEAR, RELAY until the HLDR, WINDOWgoes to the lowest part and stops.RadioFans.CN 收音机爱 好者资料库 11 PHASES ALIGNMENTJoinbGEAR RELAYGEAR, RELAY WINDOW2) APPLY GREASE (FG-87H) BOTH SIDE of the RIB.1) Turn GEAR RELAY until. This LEVER is stopped. (SEE a)ca* Mount in order. 1), 2), 3).3) Mount GEAR, RELAY WINDOW to put together b and c.*Align the position b with position c.1mma, b STEPAPPLY CFD-409 on the RAIL(From top to BOTTOM)JOIN with RACK1) Rotate the GEAR RELAY to open the DECK. Rotate it until it can rotate no more.2) Engage the gear so that the HDLR. MECH ASSY comes to the same height as the top (0 portion) of HLDR. WINDOW. abbaHLDR, WINDOWHDR,MECHA ASSYRadioFans.CN 收音机爱 好者资料库 12 DESCRIPTIONREF. NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO.ELECTRICAL MAIN PARTS LISTIC 8B-NF8-645-010 C-IC,LC877256A-5V18 8B-NF8-646-010 C-IC,LC877264V-5V24 87-A21-831-010 IC,SPS-422-1-F1 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-893-040 C-IC,NJM4558V-TE2 87-A21-401-040 C-IC,M61503FP 87-070-289-040 IC,BU2092F 87-A21-695-010 IC,LA1845L 87-A20-440-040 C-IC,BU1920FS 87-A21-928-010 IC,LC72131D-N 87-020-454-010 IC,DN6851TRANSISTOR 87-A30-559-010 TR,CSB1370EF 87-A30-492-080 TR,2SC5343G 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-494-080 TR,2SA1980G 87-A30-107-070 C-TR,CMBT5401 87-A30-484-080 C-TR,KRA102S 87-A30-190-080 TR,CC5551 87-A30-106-040 C-TR,CMBT5551 87-A30-306-010 TR,2SB1677 87-A30-528-010 TR,2SB1686 87-A30-307-010 TR,2SD2619 87-A30-529-010 TR,2SD2642 87-A30-490-080 C-TR,KRC107S 87-A30-162-010 FET,2SK2937 87-A30-582-080 TR,CDA1585BC 87-A30-495-080 TR,2SA1981Y 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-063-080 C-TR,KRA104S 87-A30-520-080 TR,2SC5342Y 87-A30-515-080 TR,2SA1979O/Y 87-A30-087-080 C-FET,2SK2158 87-A30-090-080 FET,2SK2541 89-327-143-080 C-TR,2SC2714O 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E 87-A30-086-040 C-TR,CSD1306E 87-A30-234-080 TR,CSC4115BCDIODE 87-A40-393-090 DIODE,1N5402GW(F20) 87-A40-291-080 DIODE,1N4148M(CPT) 87-A40-455-090 DIODE,RL203 GW 87-A40-764-080 ZENER,UZ10BSC 87-A40-553-080 DIODE,1N4003 LES 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-488-080 DIODE,1SS244 87-A40-748-080 ZENER,UZ5.6BSA 87-A40-002-080 ZENER,MTZJ5.1C 87-A40-747-080 ZENER,UZ5.1BSB 87-A40-749-080 ZENER,UZ5.6BSB 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2LMAIN C.B C3 87-012-368-080 C-CAP,S 0.1-50 F C4 87-012-368-080 C-CAP,S 0.1-50 F C5 87-012-368-080 C-CAP,S 0.1-50 F C6 87-012-368-080 C-CAP,S 0.1-50 F C9 87-010-759-080 C-CAP,U, 0.1-25F C9 87-010-196-080 CHIP CAPACITOR,0.1-25 C10 87-010-759-080 C-CAP,U, 0.1-25F C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C11 87-010-759-080 C-CAP,U, 0.1-25F C11 87-010-196-080 CHIP CAPACITOR,0.1-25 C12 87-010-759-080 C-CAP,U, 0.1-25F C12 87-010-196-080 CHIP CAPACITOR,0.1-25 C19 87-A12-776-090 CAP,E 2200-50 M 85 SKR C19 87-A12-382-000 CAP,E 2200-63 M 85 IV LELON C19 87-A12-779-090 CAP,E 3300-50 M 85 KR C20 87-A12-776-090 CAP,E 2200-50 M 85 SKR C20 87-A12-779-090 CAP,E 3300-50 M 85 KR C20 87-A12-382-000 CAP,E 2200-63 M 85 IV LELON C21 87-A12-777-090 CAP,E 3300-25 M 85 SKR C21 87-A12-782-090 CAP,E 4700-25 M 85 SKR C21 87-A12-778-090 CAP,E 3300-35 M 85 SKR C22 87-A12-777-090 CAP,E 3300-25 M 85 SKR C22 87-A12-778-090 CAP,E 3300-35 M 85 SKR C32 87-010-197-080 CAP, CHIP 0.01 DM C32 87-012-286-080 CAP, U 0.01-25 C33 87-A12-062-080 CAP,E 100-10 SMG C34 87-A12-072-080 CAP,E 100-25 SMG C35 87-A12-071-080 CAP,E 47-25 SMG C35 87-A12-090-080 CAP,E 4.7-50 SMG C36 87-A12-066-080 CAP,E 47-16 SMG C36 87-A12-067-080 CAP,E 330-16 SMG C38 87-010-197-080 CAP, CHIP 0.01 DM C38 87-012-286-080 CAP, U 0.01-25 C60 87-A12-089-080 CAP,E 3.3-50 SMG C61 87-A12-071-080 CAP,E 47-25 SMG C83 87-A12-074-080 CAP,E 470-25 SMG C97 87-010-831-080 C-CAP,U,0.1-16F C101 87-012-279-080 C-CAP,U 2700P-50 B C102 87-012-279-080 C-CAP,U 2700P-50 B C103 87-A12-084-080 CAP,E 0.22-50 SMG C104 87-A12-084-080 CAP,E 0.22-50 SMG C105 87-012-277-080 C-CAP, U 1800P-50 B C106 87-012-277-080 C-CAP, U 1800P-50 B C107 87-A12-089-080 CAP,E 3.3-50 SMG C108 87-A12-089-080 CAP,E 3.3-50 SMG C109 87-012-195-080 C-CAP,U 100P-50CH C110 87-012-195-080 C-CAP,U 100P-50CH C111 87-A12-077-080 CAP,E 33-35 SMG C112 87-A12-077-080 CAP,E 33-35 SMG C113 87-A10-596-080 C-CAP,S 100P-100 J CH C114 87-A10-596-080 C-CAP,S 100P-100 J CH C117 87-012-368-080 C-CAP,S 0.1-50 F C118 87-012-368-080 C-CAP,S 0.1-50 F C119 87-012-286-080 CAP, U 0.01-25 C120 87-012-286-080 CAP, U 0.01-25 C123 87-010-177-080 C-CAP,S 820P-50 SL C124 87-010-177-080 C-CAP,S 820P-50 SL C133 87-012-282-080 CAP, U 4700P-50 C140 87-012-278-080 C-CAP,U 2200P-50 B C186 87-010-759-080 C-CAP,U, 0.1-25F C187 87-A12-091-080 CAP,E 10-50 SMG C188 87-A12-091-080 CAP,E 10-50 SMG C225 87-012-368-080 C-CAP,S 0.1-50 F C226 87-012-368-080 C-CAP,S 0.1-50 F C227 87-012-368-080 C-CAP,S 0.1-50 F C228 87-012-368-080 C-CAP,S 0.1-50 F C229 87-010-191-080 C-CAP,S 0.015-50 F C230 87-010-1