Aiwa-CXJN1-cs-sm维修电路原理图.pdf

SERVICE MANUALCOMPACT DISC DECK RECEIVERAEP ModelUK ModelE ModelAustralian ModelCX-JN1Ver. 1.4 2004.109-877-271-05Sony Corporation2004J05-1Personal Audio Company 2004.10Published by Sony Engineering CorporationSPECIFICATIONSCX-JN1 is the amplifier, CD player, tape deckand tuner section in JAX-N1/PK1.Model Name Using Similar MechanismNEWCD Mechanism TypeCDM74S-K6BD72CDBase Unit NameBU-K6BD72SectionOptical Block NameKSM-213DCPOptical Pick-up NameKSS-213DTape deckModel Name Using Similar MechanismNEWSectionTape Transport Mechanism typeCWM43FF13TUNERFM Except CIS model:tuning range87.5 MHz to 108 MHzFM AEP, UK models: CIS model: Except AEP, UK, CIS models: usable sensitivity (IHF)16.8 dBfFM antenna terminal75 ohms (unbalanced)AM AEP, UK, CIS, E, EA, TW models:E51 model:tuning range531 kHz to 1602 kHzAM usable sensitivity350 V/mSP, KR, AUS models:530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) AM antennaLoop antennaAMPLIFIERPower AEP, UK, CIS models: Except AEP, UK, CIS models: outputRated: 12 W + 12 W (6 ohms, T.H.D.1 %, 1 kHz/DIN 45500)Reference: 15 W + 15 W (6 ohms,T.H.D. 10 %, 1 kHz/DIN 45324)MUSIC POWER: 27 W +27 WTotal harmonic distortion0.08 % (6 W, 1 kHz, 6 ohms, DINAUDIO)CASSETTE DECKTrack format4 tracks, 2 channels stereoFrequency response50 Hz 8 kHzRecording systemAC biasHeadsDeck A: playback x 1Deck B: recording/playback x 1,erase x 1CD PLAYERLaserSemiconductor laser( = 780 nm)Emission duration:continuousD/A converter1 bit dualSignal-to-noise ratio85 dB (1 kHz, 0 dB)Harmonic distortion0.05 % (1 kHz, 0 dB)GENERALPower AEP, UK, CIS models: E, E51, SP, TW models: AEP, UK, CIS models: AEP, UK, CIS models: KR model: AUS model: Except AEP, UK, CIS models: (Except AEP, UK, CIS models)requirements230 V AC, 50/60 HzPower consumption40 WPower consumptionWith ECO mode on: 0.25 W in standby modeWith ECO mode off: 15 WDimensions (W x H x D)280 x 330 x 392.5 mmWeight6.1 kgSpecifications and external appearance are subject to changewithout notice.CIS model:65 MHz to 74 MHz (10 kHz step)87.5 MHz to 108 MHz (50 kHz step)15.3 dBf (65 MHz to 74 MHz)12.8 dBf (87.5 MHz to 108 MHz)13.2 dBf530 kHz to 1710 kHz (10 kHz step)531 kHz to 1710 kHz (9 kHz step)Rated: 36 W + 36 W (1 kHz, T.H.D. 1%, 6 ohms)Reference: 45 W + 45 W (1 kHz,T.H.D. 10 %, 6 ohms)110 220 V AC, 60 Hz240 V AC, 50 Hz/60 Hz- 120V / 220 - 240V AC(Switchable), 50 Hz/60 HzEA models: 120 - 127V / 220 V AC (Switchable), 50 Hz/60 Hz74 WE, EA, SP, TW, KR, AUS models: 6.8 kgE51 model: 6.7 kgInputVIDEO/AUX: 400 mVOutputsSPEAKER: MIC: 1.7 mV (10k ohms)6 ohms or morePHONES: 32 ohms or more Continued on next page RadioFans.CN 收音机爱 好者资料库CX-JN12Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam-aged by heat.Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur-ing repairing. Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times). Be careful not to apply force on the conductor when solderingor unsoldering.CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous ra-diation exposure.SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.The following caution label is located inside the unit.This appliance is classified asa CLASS 1 LASER product.The CLASS 1 LASERPRODUCT MARKING islocated on the rear exterior.COPYRIGHTCheck copyright laws relevant to recordings from discs, tuneror tape for the country where the unit is to be used.Licensed by BBE Sound, Inc. under USP4638258, 5510752and 5736897. AbbreviationAUS : Australian modelEA: Saudi Arabia modelE51 : Chilean and Peruvian modelsKR: Korean modelSP: Singapore modelTW : Taiwan modelVer 1.2RadioFans.CN 收音机爱 好者资料库CX-JN13TABLE OF CONTENTS1.SERVICING NOTES.42.GENERALLocation of Controls .73.DISASSEMBLY3-1.Disassembly Flow .93-2.Case (SIDE-L/R). 103-3.Case (Top) . 103-4.Tray Panel. 113-5.CD Mechanism Deck (CDM74S-K6BD72). 113-6.Front Panel Section . 123-7.Mechanical Deck (CWM43FF13) . 123-8.Rear Cabinet Section . 133-9.PT Board, MAIN Board. 133-10. Table Assy . 143-11. Motor (TB) Board . 143-12. Motor (LD) Board. 153-13. Base Unit (BU-K6BD72). 153-14. Motor Gear Assy (Sled) (M701), BD Board . 164.TEST MODE. 175.ELECTRICAL ADJUSTMENTSCD Section . 196.DIAGRAMS6-1.Block Diagram CD Section . 206-2.Block Diagram TUNER/TAPE/PANEL Section . 216-3.Block Diagram AMP/POWER SUPPLY Section . 226-4.Note for Printed Wiring Boards andSchematic Diagrams . 236-5.Printed Wiring Board BD Section . 246-6.Schematic Diagram BD Section . 256-7.Printed Wiring Boards CHANGER Section . 266-8.Schematic Diagram CHANGER Section . 276-9.Schematic Diagram MAIN Section (1/4) . 286-10. Schematic Diagram MAIN Section (2/4) . 296-11. Schematic Diagram MAIN Section (3/4) . 306-12. Schematic Diagram MAIN Section (4/4) . 316-13. Printed Wiring Board MAIN Section . 326-14. Printed Wiring Board HP Section . 336-15. Schematic Diagram HP Section . 336-16. Printed Wiring Board PANEL Section . 346-17. Schematic Diagram PANEL Section . 356-18. Printed Wiring Boards KEY Section . 366-19. Schematic Diagram KEY Section . 376-20. Printed Wiring Board PT Section (AEP, UK, CIS, MX, KR, AUS) . 386-21. Schematic Diagram PT Section (AEP, UK, CIS, MS, KR, AUS). 396-22. Printed Wiring Board PT Section (E, E51, SP, TW) . 406-23. Schematic Diagram PT Section (E, E51, SP, TW) . 416-24. IC Pin Function Description . 457.EXPLODED VIEWS7-1.Case Section . 477-2.Front Panel Section-1. 487-3.Front Panel Section-2. 497-4.Front Panel Section-3. 507-5.Front Panel Section-4. 517-6.Chassis Section . 527-7.CD Mechanism Deck Section-1(CDM74S-K6BD72) . 537-8.CD Mechanism Deck Section-2(CDM74S-K6BD72) . 547-9.CD Mechanism Deck Section-3(CDM74S-K6BD72) . 557-10. Base Unit Section (BU-K6BD72) . 568.ELECTRICAL PARTS LIST. 57Ver 1.2 AbbreviationAUS : Australian modelEA: Saudi Arabia modelE51 : Chilean and Peruvian modelsKR: Korean modelSP: Singapore modelTW : Taiwan modelRadioFans.CN 收音机爱 好者资料库4CX-JN1SECTION 1SERVICING NOTESNOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNITThe laser diode in the optical pick-up block may suffer electro-static break-down because of the potential difference generatedby the charged electrostatic load, etc. on clothing and the humanbody.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.LASER DIODE AND FOCUS SEARCH OPERATIONCHECKCarry out the “S curve check” in “CD section adjustment” andcheck that the S curve waveforms is output three times. MODEL IDENTIFICATION Back Panel MODELPART No.CIS model4-245-154-4E, Singapore and Taiwan models4-245-201-0Chilean and Peruvian models4-245-201-2AEP and UK models4-245-201-3Korean and Australian models4-245-201-6Saudi Arabia model4-245-279-0PART No.UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size): LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher thanordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful! Strong viscosityUnleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridges oc-cur such as on IC pins, etc. Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.Ver 1.2RadioFans.CN 收音机爱 好者资料库5CX-JN1HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF.3Pull-out the disc tray.1Remove the case (side-L).2Turn the loading gear in the direction of arrow A.ARadioFans.CN 收音机爱 好者资料库6CX-JN1SERVICE POSITION CD mechanism deck Tape mechanism deck main board (CN691)Connect wire (flat type) (19 core) tomain board (CN691) and BD board (CN710).BD board (CN710)BD board (CN710)Connect wire (flat type) (13 core) topanel board (CN601) and mechanical deck.panel board (CN601)main board (CN301)RadioFans.CN 收音机爱 好者资料库7CX-JN1SECTION 2GENERALThis section is extracted frominstruction manual.En1 DISC CHANGE Rotates the CD trays.2 POWER 6STANDBY/ON Switches the unit on and off (standby).The red indicator flashes when receiving a signal fromthe remote.3 MODE Selects various modes (ECO and Repeat/Shuffle/Programmed playback, etc.) when used in combinationwith ENTER and MULTI JOG.4 ENTER Fixes the modes and the time (ECO, Repeat/Shuffle/Programmed playback, clock, and timer, etc.) when usedin combination with ENTER and MULTI JOG.! Remote sensorReceives a signal from the remote. VOLUME Adjusts the volume.# TREBLE Enhances high frequency sound.$ BASS Emphasizes low frequency sound.% i-Bass Produces rich and clear low frequency sound. PTY (AEP, UK) Displays a program type for RDS (Radio Data System)RT (AEP, UK) Displays text information for RDS (Radio Data System)& cPLAY/PRESET When the unit is turned off: activates or deactivatesDEMO.CD and Tape: starts playback.Tuner: tunes into a preset station.sSTOP/CLEAR CD and Tape: stops playback.Tuner: clears a station preset.fTUNING DOWN, gTUNING UPCD: searches a track in fast forward or fast reverseplayback when held down.Tape: fast forwards or rewinds the tape.Tuner: manually tunes down or up within the band.aPAUSE/SET CD and Tape: pauses playback.Tuner: stores the received station in to preset.Main unit: front5 MULTI JOG When used in combination with ENTER and MULTI JOG,CD: selects a track and Repeat/Shuffle/Programmedplayback.Tuner: selects a preset station.Tape: specifies tape length.Clock and Timer: sets the time.i-Bass: selects a frequency range.Spectrum analyzer, ECO and Dimmer: selects the mode.6 PHONES jackPlug in here an optional headphones set with a ministereo plug (3.5 mm). Speaker output is canceled.7 SYNC DUB Starts dubbing a whole tape.wREC/REC MUTING Starts recording.8 DISC DIRECT PLAY 1-3 Selects a disc.9 zOPEN/CLOSE Opens or closes the disc compartment.0 TAPE A/B Selects Tape function, and deck A or B.TUNER/BAND Selects Tuner function and the radio band.VIDEO/AUX Selects the function of external equipment connected toVIDEO/AUX jacks.CD Selects CD function.* MIC MIXING (Except AEP, UK, CIS)Adjusts the microphone volume.MIC jack (Except AEP, UK, CIS)Connects the microphone here.Main unit: rear1 AM LOOP, FM 75 terminals Plug in the supplied AM and FM antennas here.2 VIDEO/AUX jacksAccepts analog sound signals from external equipment.Connect using an optional connecting cable with RCAphono plugs (red plug to R jack, white plug to L jack).Refer also to the operating instructions of your equipment.To switch function to external input, press VIDEO/AUX.Tip:To change the displayed name for this function, turn theunit on, then hold down VIDEO/AUX and press POWERon the unit. Repeat the procedure to select VIDEO,AUX or TV.3 # SPEAKER terminals Connect the speaker cord of the supplied front speakershere.4 AC voltage selector (E, Chilean, Peruvian, Saudi Arabia, Singapore, Taiwan)Switches AC voltage between 110 - 120V and 220 - 240V.Make sure it matches your local voltage.5 AC power cord LOCATION OF CONTROLSVer 1.2RadioFans.CN 收音机爱 好者资料库8CX-JN1Buttons with the same or similar names with the main unitbasically have the same function.1 POWER 2 1-0/10, +10 CD: selects a CD track of the specified number.Tuner: tunes in to the station with the specified presetnumber.The numbered buttons take on these functions below when pressedwith SHIFT held down:EDIT Enters AI Edit Recording or Programmed Edit Recordingmode when pressed in stop mode.BAND Selects Tuner function and the radio band.TAPE A/B TUNER MODE Switches between stereo or monaural FM reception.3 r, t CD: selects a track.Tuner: selects a preset station.Tape: specifies tape length.BASS and TREBLE: adjusts the level.Clock and Timer: sets the time.4 PLAY MODE Selects Shuffle or Programmed playback in CD function.REPEAT Enters CD repeat playback mode.ENTER 5 CLOCK/TIMER/SETEnters timer setting mode.CLOCK/TIMER/SELECT Selects timer playback, timer recording or timer off.6 DISPLAY Displays the time and the remaining time for CD.7 SHIFTHold down when pressing a numbered button to changeits function to that printed above the number.e.g.)Press SHIFT+BAND on the remote indicates Holddown SHIFT and press 2 (BAND). Doing so makes yoube able to select Tuner function and the radio band.8 FUNCTIONSwitches the active function among CD, TAPE, TUNERand VIDEO (AUX or TV).9 DISC SKIP Select a disc.0 c/d When the unit is turned off: activates or deactivatesDEMO.CD and Tape: starts playback.sCD and Tape: stops playback.f,g CD: searches a track in fast forward or fast reverseplayback when held down.Tape: fast forwards or rewinds the tape.Tuner: manually tunes down or up within the band.a CD and Tape: pauses playback.! SLEEP Switches the sleep-timer on/off and selects the duration. VOLUME (+, -) Adjusts the volume.# SOUND Selects BASS or TREBLE setting modeCLEAR Clears a track of the CD programmed playback and aRadio preset station.NoteThe The button not explained above (KARAOKE) does notoperate for AEP, UK and CIS models.buttons not explained above (ALBUM N, Mand SPECTRUM) do not operate for this unit. Remote controlKARAOKE (Except AEP, UK, CIS)Selects a Multiplex mode.Setting the clockUse the remote.1Press CLOCK/TIMER/SET.Go to step 3 when the time appears and the hour flashes.2Press r or t repeatedly until CLOCKSET appears in the display and then pressENTER.3Press r or t repeatedly to set the hourand then press ENTER.4Press r or t repeatedly to set the minuteand then press ENTER.The time display stops flashing and the clock starts from00 seconds.MULTI JOG is also available in place of r or t.To display the timePress DISPLAY on the remote. The time will be displayed for6 seconds.If - -:- - appears when the unit is turned offThere has been a power interruption. Re-set the clock.Ver 1.1RadioFans.CN 收音机爱 好者资料库CX-JN19 This set can be disassembled in the order shown below.3-1.DISASSEMBLY FLOWSECTION 3DISASSEMBLYSet3-2.CASE(SI