Fostex-CR300-cd-tape维修电路原理图.pdf

Service ManualModelCOMPACT DISC RECORDERFOR U.S. MODELSNECESSARY INFORMATION FOR DHHSRULES MARKED ON THE REAR BASE AND ONTHE TOP OF CD MECHANISM AS BELOW.DANGER - LASER RADIATION WHEN OPEN.AVOID DIRECT EXPOSURE TO BEAM.RadioFans.CN 收音机爱 好者资料库SAFETY INSTRUCTIONSRead instructions - All the safety and operating instruc-tions should be read before the appliance is operated.Retain instructions - The safety and operating instructionsshould be retained for future reference.Heed warnings - All warnings on the appliance and in theoperating instructions should be adhered to.Follow instructions - All operating and use instructionsshould be followed.Water and Moisture - The appliance should not be usednear water - for example, near a bathtub, washbowl,kitchen sink, laundry tub, in a wet basement, or near aswimming pool, and the like.Carts and Stands - The appliance should be used onlywith a cart or stand that is recommended by the manufac-turer.An appliance and cart combination should be moved withcare. Quick stops, excessive force, and uneven surfacesmay cause the appliance and cart combination to over-turn.Wall or Ceiling Mounting - The appliance should bemounted to a wall or ceiling only as recommended by themanufacturer.Ventilation - The appliance should be situated so that itslocation or position does not interfere with its proper ven-tilation. For example, the appliance should not be situ-ated on a bed, sofa, rug, or similar surface that may blockthe ventilation openings; or, placed in a built-in installa-tion, such as a bookcase or cabinet that may impede theflow of air through the ventilation openings.Heat - The appliance should be situated away from heatsources such as radiators, heat registers, stoves, or otherappliances (including amplifiers) that produce heat.Power Sources - The appliance should be connected to apower supply only of the type described in the operatinginstructions or as marked on the appliance.Grounding or Polarization - The precautions that shouldbe taken so that the grounding or polarization means ofan appliance is not defeated.Power Cord Protection - Power supply cords should berouted so that they are not likely to be walked on orpinched by items placed upon or against them, payingparticular attention to cords at plugs, convenience recep-tacles, and the point where they exit from the appliance.Cleaning - The appliance should be cleaned only as rec-ommended by the manufacturer.Nonuse Periods - The power cord of the appliance shouldbe unplugged from the outlet when left unused for a longperiod of time.Object and Liquid Entry - Care should be taken so thatobjects do not fall and liquids are not spilled into the en-closure through openings.Damage requiring Service - The appliance should be ser-viced by qualified service personnel when:A.B.C.D.E.Servicing - The user should not attempt to service the ap-pliance beyond that described in the operating instruc-tions. All other servicing should be referred to qualifiedservice personnel.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE.TO PREVENT ELECTRIC SHOCK, MATCHWIDE BLADE OF PLUG TO WIDE SLOT,FULLY INSERT.POUR VITER LES CHOCS LECTRIQUES,INTRODUIRE LA LAME LA PLUS LARGE DELA FICHE DANS LA BORNE CORRE-SPONDANTE DE LA PRISE ET POUSSERJUSQU AU FOND.CAUTION:ATTENTION:The exclamation point within an equilateraltriangle is intended to alert the user to thepresence of important operating and mainte-nance (servicing) instructions in the literatureaccompanying the appliance.The lightening flash with arrowhead symbol,within an equilateral triangle, is intended toalert the user to the presence of uninsulated“dangerous voltage” within the products en-closure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.“WARNING”“TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS-TURE.”1.2.3.4.5.6.7.8.The power supply cord or the plug has been damaged;orObjects have fallen, or liquid has been spilled into theappliance; orThe appliance has been exposed to rain; orThe appliance does not appear to operate normally orexhibits a marked changed in performance; orThe appliance has been dropped, or the enclosuredamaged.9.10.11.12.13.14.15.16.17.RadioFans.CN 收音机爱 好者资料库CR3003The following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testersuch as Simpson Model 229-2 or equivalent between theearth ground and all exposed metal parts of the appliance(input/output terminals, screw heads, metal overlays,control shaft, etc.). Plug the AC line cord of the appliancedirectly into a 120V AC 60Hz outlet and turn the AC powerswitch on. Any current measured must not exceed 0.5mA.SAFETY PRECAUTIONSLeakagecurrenttesterReading shouldnot be above0.5mADeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)EarthgroundAC Leakage TestANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF A POTENTIALSHOCK HAZARD AND MUST BE CORRECTED BEFORERETURNING THE APPLIANCE TO THE CUSTOMER.Many electrical and mechanical parts in the appliance havespecial safety related characteristics. These are often notevident from visual inspection nor the protection affordedby them necessarily can be obtained by using replacementcomponents rated for voltage, wattage, etc. Replacementparts which have these special safety characteristics areidentified in this Service Manual.Electrical components having such features are identifiedby marking with a on the schematics and on the parts listin this Service Manual.The use of a substitute replacement component which doesnot have the same safety characteristics as the PIONEERrecommended replacement one, shown in the parts list inthis Service Manual, may create shock, fire, or otherhazards.Product Safety is continuously under review and newinstructions are issued from time to time. For the latestinformation, always consult the current PIONEER ServiceManual. A subscription to, or additional copies of, PIONEERService Manual may be obtained at a nominal charge fromPIONEER.2. PRODUCT SAFETY NOTICE(FOR USA MODEL ONLY)NOTICE(FOR CANADIAN MODEL ONLY)Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts mustbe of identical designation.REMARQUE(POUR MODLE CANADIEN SEULEMENT)Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les picesde remplacement doivent avoir la mme dsignation.This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have beentrained to properly and safely repair complex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and mayvoid the warranty. If you are not qualified to perform the repair of this product properly and safely,you should not risk trying to do so and refer the repair to a qualified service technician.WARNINGThis product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California tocause cancer, birth defects or other reproductive harm.Health & Safety Code Section 25249.6 Proposition 65CR30041. Laser Interlock MechanismThe position of the switch (S601) for detecting loadingstate is detected by the system microprocessor, and thedesign prevents laser diode oscillation when the switch(S601) is not on CLMP terminal side (CLMP signal is OFFor high level.). Thus, the interlock will no longer function ifthe switch (S601) is deliberately set to CLMP terminal side(low level).The interlock also does not function in the test mode *.Laser diode oscillation will continue, if pin 1 of M51593FP(IC101) on the PRE-AMP BOARD ASSY mounted on thepickup assembly is connected to GND, or pin 19 isconnected to low level (ON), or else the terminals of Q101are shorted to each other (fault condition).2. When the cover is opened with the servo mechanism blockremoved and turned over, close viewing of the objectivelens with the naked eye will cause exposure to a Class 1laser beam.Additional Laser Caution* Refer to page 13.IMPORTANTTHIS PIONEER APPARATUS CONTAINSLASER OF CLASS b.SERVICING OPERATION OF THE APPARATUSSHOULD BE DONE BY A SPECIALLYINSTRUCTED PERSON.LASER DIODE CHARACTERISTICSMAXIMUM OUTPUT POWER: 23 mWWAVELENGTH: 778 - 787 nmLABEL CHECKCR300 USAPrinted on Rear PanelPrinted on Rear PanelCR300 EURCR300 EURCR300 EURCR3005Parts marked with this sign are safety critical components. They must always be replaced with identicalcomponents. Refer to the Fostex Parts List and ensure exact replacement.CAUTIONTABLE OF CONTENTS1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. CONTROLS, INDICATORS & CONNECTORS . . . . . . . . . . .3. ADJUSTMENT PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . .4. ASSEMBLING & DISASSEMBLING . . . . . . . . . . . . . . . . . .5. EXPLODED VIEW, PCB ASSEMBLY & PARTS LIST . . . . .6. CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . .Adjusting procedures, assembling & disassembling, exploded view, PCB assembly, parts list, circuit diagramsand general information are given in this manual to assist the service technician in maintaining the ModelCR300.NOTES*6913 19253750CR30061. SPECIFICATIONSFUNCTION LISTAutomatic Disk RecognitionSampling Rate ConverterAutomatic conversion (48 kHz, 32 kHz 44.1 kHz)ON/OFF switchable (44.1 kHz)Synchronous RecordingSynchronous to one song / all songs / DAT IDAuto Stop Delay in Digital Synchro0 sec, 10 sec, offCopy Bit SettingNo restriction / one time only / prohibitedAuto Track Increment6 levelsManual Track IncrementREC MUTEFade In / Fade OutFade time: 6 sec, 9 sec, 12 sec, 18 secPREVIOUSEnd section of previous track can be played back while inREC PAUSE modeErase Mode (CD-RW)Last Track, All Track, Disc, TOCDirect SearchOperational through remote controller onlyTrack SearchManual SearchOne Song / All Song / Program RepeatOperational through remote controller onlyProgram PlaybackSkip PlaybackSampling MonitorDisplayed TimeElapsed playback time, Remaining playback time,Total remaining playback time, Total playback time,Elapsed recording time, Remaining recording time,Total recording timeLaser Hour MeterMargin DisplayAuto PauseAuto Power CalibrationRemote Controller On / OffDigital Out On / OffBalanced Input Sensitivity Switching+ 4 dBu / -10 dBVDISPLAYFL DisplayPlay, Pause, REC (Rec), RPT-1 (Repeat, 1-Repeat),AUTO TRACK (Auto Track No.), PGM (Program),FADER (Fader), SKIP ON (Skip ON/OFF),32/44/48 (Input sampling frequency),SYNC (Digital Synchronous Recording),CD-RW/FINALIZE (Disc Type)LED DisplayTrack number, Level meter, Elapsed playback time,Remaining playback time, Total remaining playback time,Total playback time, Elapsed recording time,Remaining recording time, Total recording timeINPUT/OUTPUT TERMINALAudio Input (Input Impedance)RCA pin (27 k or more)Balanced XLR-3 (10 k)Audio Output (Output Impedance)RCA pin (1 k)Balanced XLR-3 (1 k or less)CR3007DIMENSIONS & WEIGHTMaximum Dimensions482 (W) x 105 (H) x 393 (D) mm19 (W) x 4 - 1/8 (H) x 15 - 1/2 (D) inchWeight (w/o package)7.0 kg (15.4 lb)POWER REQUIREMENTPower SupplyAC120 V, 60 HzAC220 230 V, 50/60 HzPower Consumption24 WAUDIO UNIT CHARACTERISTICSCD Playback (Analog RCA Output)Frequency Response4 Hz 20 kHz 1.0 dB (EIAJ)S/N100 dB or more (EIAJ)Dynamic Range90 dB or more (EIAJ)Total Harmonic Distortion0.01 % or less (EIAJ)Channel Separation90 dB or more (EIAJ)De-emphasis Deviation0 1.5 dB or less (EIAJ)Level Difference between Channels1 dB or less (EIAJ)Output Voltage2.0 0.3 Vrms (Load impedance: 10 k, EIAJ)Monitor (Analog RCA Input Analog RCA Output)Frequency Response4 Hz 20 kHz 1.0 dB (EIAJ)S/N83 dB or more (EIAJ)Dynamic Range83 dB or more (EIAJ)Total Harmonic Distortion0.01 % or less (EIAJ)Maximum Input Level3.2 Vrms or more (EIAJ)Minimum Input Level0.4 Vrms or less (EIAJ)56781234PLAYGNDPAUSEMANUAL TRACKNo. WRITESTOPRECPARALLEL REMOTE TERMINALINPUT/OUTPUT TERMINAL (continued)Digital Input (Input Impedance)Optical EIAJ CP-1201 TYPE2Coaxial RCA IEC958 (75 )AES/EBU XLR-3 (110 )Digital Output (Output Impedance)Optical EIAJ CP-1201 TYPE2Coaxial RCA IEC958 (75 )Headphone Output 6 (1/4 inch) standard stereo phone jackParalell Remote ControlDIN 8-pinCR3008AUDIO UNIT CHARACTERISTICS (continued)Record & Playback (Analog RCA Input Analog RCA Output)Frequency Response4 Hz 20 kHz 1.0 dB (EIAJ)S/N83 dB or moreDynamic Range83 dB or moreTotal Harmonic Distortion0.01 % or lessMonitor (Digital Coaxial Input Analog RCA Output)Frequency Response4 Hz 20 kHz 1.0 dB (EIAJ)S/N95 dB or more (EIAJ)Dynamic Range90 dB or more (EIAJ)Total Harmonic Distortion0.01 % or less (EIAJ)Maximum Input Level0.6 Vp-p or more (EIAJ)Minimum Input Level0.2 Vp-p or less (EIAJ)Record & Playback (Digital Coaxial Input Analog RCA Output)Frequency Response4 Hz 20 kHz 1.0 dB (EIAJ)S/N95 dB or moreDynamic Range90 dB or moreTotal Harmonic Distortion0.01 % or lessCD Playback (Analog XLR-3 +4 dBu Output)Frequency Response4 Hz 20 kHz + 1.0, -1.5 dB (EIAJ)S/N100 dB or more (EIAJ)Dynamic Range90 dB or more (EIAJ)Total Harmonic Distortion0.01 % or less (EIAJ)Channel Separation90 dB or more (EIAJ)De-emphasis Deviation0 1.5 dB or less (EIAJ)Level Difference between Channels1 dB or less (EIAJ)Output Voltage20 1.5 dBm (Load impedance: 100 k, EIAJ)Output Voltage (-10 dBV)8 1.0 dBm (Load impedance: 100 k, EIAJ)Monitor (Analog XLR-3 +4 dBu Input Analog XLR-3 +4 dBu Output)Frequency Response4 Hz 20 kHz + 1.0, -1.5 dB (EIAJ)S/N83 dB or more (EIAJ)Dynamic Range83 dB or more (EIAJ)Total Harmonic Distortion0.01 % or less (EIAJ)Maximum Input Level13 Vrms or more (EIAJ)Minimum Input Level (-10 dBV)0.4 Vrms or less (EIAJ)Record & Playback (Analog XLR-3 +4 dBu Input Analog XLR-3 +4 dBu Output)Frequency Response4 Hz 20 kHz + 1.0, -1.5 dB (EIAJ)S/N83 dB or moreDynamic Range83 dB or moreTotal Harmonic Distortion0.01 % or lessSpecifications and appearance are subject to change without notice for product improvement.CR30092. CONTROLS, INDICATORS & CONNECTORSTIME/MARGINDIGIT ALSYCHRO12 34568101112131614 159171820212223252627292428197ANALOG086795104123DIGIT ALRECMUTEOPEN /CLOSERECORDINPUT SELECTORREC LEVELREC LEVELOPTAES / EBULINELRCOAXXLR / -10XLR / +4PHONESLEVELMAXMINMENUSETPOWEROFFONCOMP ACT DISC RECORDERCLEARSKIP PLA YFINALIZEERASEAUTO /MANUALWRITE(MANUAL)SKIP IDTRACK NO.1. Rack mount angle2. Power switch POWER3. SKIP ID set button SKIP ID SET4. SKIP ID clear button SKIP ID CLEAR5. SKIP PLAY button SKIP PLAY