Yamaha-MDXE300-md-sm 维修电路原理图.pdf

100806SERVICE MANUALMDX-E300IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherant to the industry, and more specifically YAMAHA Products, are already known and understood by the users,and have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensivecomponents and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that all service requiredshould be performed by an authorized YAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicabletechnical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA arecontinually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation toretrofit. Should any discrepancy appear to exist, please contact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to theground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.MINIDISC RECORDERFor the system operation of MDX-E300, please refer to Service Manual #100805 for the CRX-E300/NX-E300.M J modelM R, G, B model本機 動作 、CRX-E300/NX-E300 100805 覧。MDX-E300RadioFans.CN 收音机爱 好者资料库MDX-E3002MDX-E300ITO SERVICE PERSONNEL1. Critical Components InformationComponents having special characteristics are marked Zand must be replaced with parts having specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohm shuntedby 0.15F.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in bothpolarities.AC LEAKAGETESTER OREQUIVALENTEQUIPMENTUNDER TESTINSULATINGTABLEWALLOUTLETWARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/orplastic (where applicable) components may also contain traces of chemicals found by the California Health andWelfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FORANY REASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumesor expose eyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your handsbefore handling food.THE MINI DISC RECORDER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIEDSERVICE PERSONNEL.TROUBLESHOOTING . . . . .3645IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4655BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . .5657TEST POINT WAVEFORMS . . . . . . . . . . . . . . . . . . .58PRINTED CIRCUIT BOARD . . . . . . . . . . . . . . . .5962MD VOLTAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . .6364DISPLAY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6677GREASE APPLICATION DIAGRAM . . . . . . . . . . . .78REMOTE CONTROL TRANSMITTER . . . . . . . . . . .79PARTS LIST FOR CARBON RESISTORS . . . . . . .80I CONTENTSTO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . .23PREVENTION OF ELECTRO STATIC DISCHARGE . . . . . .4REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .5DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6DISASSEMBLY PROCEDURES 分解手順 . . . . . .78DISASSEMBLY OF MD RECORDER UNIT MD分解 . . . . . . . . . . . . . . . . . . .911ADJUSTMENT & TEST MODE 調整及 . . . . . . . . . . . . . . . . . . . . . . . .1229SPECIAL TEST MODE 特殊 . . . . .3031ERROR DISPLAY 表示 . . . . . . . . . . . . . .3235RadioFans.CN 收音机爱 好者资料库MDX-E300MDX-E3003WARNING: Laser SafetyThis product contains a laser beam component. This component may emit invisible, as well as visible radiation,which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions mustbe used during servicing of the unit.1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away fromthe laser pick-up unit at all times. Do not stare at the laser beam at any time.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result inhazardous radiation exposure.Laser Emitting conditions:1) When the Top Cover of the MD recorder unit is removed, and the “STANDBY/ON” SW is turned to the ON position,the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) thelaser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing during this period!If no disc is detected, the laser will stop emitting the beam. When a disc is set, you will not be exposed to any laseremissions.2) The laser power level can be adjusted with the VR on the pick-up PWB. However, this level has been set by the factoryprior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in thismanual. Adjustment of this control can increase the laser emission level from the device.VARO!: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NKYMTTMLLELASER-STEILYLLE. L KATSO STEESEEN.VARNING! : OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD OCH SPRREN R URKOPPLAD.BETRAKTA EJ STRLEN.Laser Diode PropertiesMaterial :GaAlAsWavelength :785 nmEmission duration :ContinuousPulse Durations and Max. Output at the lens of the Laser Pick Up Unit ;Read mode :0.6 mW (Continuous)Write mode :Max 10 mW for 0.5s, Min. Cycle 1.5sANSI Class :Class 1* This output is the value measured at a distance of about 200 mm fromthe objective lens surface on the Optical Pick-up Block.Magnetic headOptical pick-upR, G, B modelsR, G, B modelsMDX-E3004MDX-E300I PREVENTION OF ELECTRO STATIC DISCHARGEThe laser diode in the MD recorder unit (optical pickup) may be damaged due to static electricity from clothes or thehuman body. Use caution to prevent electrostatic damage when servicing or handling the laser diode.1. Grounding for electrostatic damage prevention1. Worktable groundingPut a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is placed.2. Human body groundingUse an anti-static wrist strap to discharge the static electricity from your body.2. Handling of the optical pickupDo not use a tester to check the laser diode in the optical pickup. The power supply in the tester will damage thelaser diode.3. Handling Precautions for the MD recorder Unit (Optical Pickup)1. Handle the MD recorder unit (optical pickup) gently, as it is an extremely high-precision assembly.2. The flexible cable lines may break if an excessive force is applied to it. Use caution when handling the cable.3. The semi-fixed resistor for laser power adjustment should not be adjusted. Do not turn the resistor.1MConductive material(sheet) or steel sheetAnti-static wrist stripI REAR PANELSM R modelM B modelM G modelM J modelMDX-E300MDX-E3005I SPECIFICATIONSDigital audio systemSystem形式MiniDisc digital audio systemDiscMiniDiscRecording method記録方式Magnetic field variation overwriteReading method再生読取方式Non-contact optical pickup (using semiconductor laser)LaserSemiconductor laserRecord/playback time録音再生時間Max. 80 min. (on stereo)Max. 161 min. (on ATRAC3-LP2)Max. 323 min. (on ATRAC3-LP4)Revolutions 回転数Approx. 400-900 rpm (CLV)Error Correction訂正方式ACIRC (Advanced Cross Interleave Reed-solomon Code)Sampling frequency周波数44.1 kHz (32 kHz and 48 kHz signals converted to 44.1 kHzfor recording)CodingATRAC (Adaptive TRansform Acoustic Coding)Modulation system変調方式EFM (Eight-to-Fourteen Modulation)Number of channels数2 (stereo) or 1 (mono, for extended recording)Frequency Response周波数特性5 - 20,000 Hz 0.5 dBSignal-to-Noise RatioSN比More than 99 dB during playbackWow and FlutterBelow measurable limitInputsLINE IN (REC) 入力Type: pin jackInput impedance: greater than 50 k-ohmsStandard input level: 300 mVDIGITAL IN (OPTICAL) 1/2 入力（光）1/2Type: square optical connector jackOutputsLINE OUT (PLAY) 出力Type: pin jackStandard output level: 2.0 0.5 VrmsDIGITAL OUT (OPTICAL) 出力（光）Type: square optical connector jackGENERALPower Supplies電源G, B models230 V, 50 HzR model110/120/220/240 V, 50/60 HzJ model100 V, 50/60 HzPower Consumption消費電力R, G, B models12WJ model11WDimensions (W x H x D)外形寸法（幅x高x奥行）217 x 88 x 297 mm (8-9/16 x 3-7/16 x 11-11/16)Weight重量2.6 kg (5 lbs. 11 oz.)Finish仕上Silver colorB, G, J modelsGold colorR, G modelsAccessories付属品Remote Control. 1Audio Pin Cable. 2Optical Cable. 1Batteries (AA, R6, UM-3). 2Specifications subject to change without notice.B : British modelG : European modelR : General modelJ : Japanese modelMDX-E3006MDX-E300I INTERNAL VIEWqMAIN (3) P.C.B.wMAIN (4) P.C.B.eMAIN (1) P.C.B.rMD RECORDER UNITtMAIN (2) P.C.B.ertwqI DIMENSIONSUnit : mm (inch)217 (8-9/16)8 (5/16)80 (3-1/8)88 (3-4/16)12 (1/2)10 (3/8)275 (10-13/16)297 (11-11/16)MDX-E300MDX-E3007CB602CB1CB6I DISASSEMBLY PROCEDURES分解手順1. Removal of Top CoverRemove 4 screws ( q ) and 4 screw ( w ) in Fig. 1.2. Removal of Front Panela. Remove 2 connectors (CB6, CB602) in Fig. 2.b. Remove 2 screws ( e ) and 2 screws ( r ) in Fig. 1.c. Detach the 2 hooks in Fig. 1 and then pull the FrontPanel forward.3. Removal of MD Recorder Unita. Remove 1 connector (CB1) in Fig. 2.b. Remove 4 screws ( t ) in Fig. 1.c. Remove the MD Recorder Unit.1. 外方q4本w4本外。（Fi g. 1）2. 外方a.2所 (CB6, CB602)外。（Fi g. 2）b.e2本r2本外。（Fi g. 1）c.両外、引出。3. MD外方a.1所(CB1)外。（Fi g. 2）b.t4本外。（Fi g. 1）c.MD取外。Remove parts in disassembly order as numbered.(番号順取外行。）Fig. 1Fig. 2qqwwwtteerHookHookTop CoverFront PanelMD Recorder UnitMDMDX-E3008MDX-E300G a. y 2 本外。 （Fi g. 3）b. u 2 本外。 （Fig. 4）c. Mai n (1) P. C. B.外。d. Mai n (1) P. C. B. Mai n (4) P. C. B.Fi g. 5置、動作行。G Service Positiona. Remove 2 screws (y) in Fig. 3.b. Remove 2 screws (u) in Fig. 4.c. Remove the Main (1) P.C.B. from the chassis.d. Place the Main (1) P.C.B. and Main (4) P.C.B. as shownin Fig. 5 for servicing.Fig. 3Fig. 4Fig. 5MAIN (1)MAIN (4)yuuClothP.C.B. 場合Main (4) P.C.B. ST1 線等接続。When checking the P.C.B.:Be sure to connect the ST1 of the Main (4) P.C.B. to thechassis with a jumper wire or the like.（1）（4）布ST1ChassisMDX-E300MDX-E3009Removal of MD Main P.C.B. and MD Mechanism (Fig. 6)1. Remove 3 screws (K1) and then remove the TopCover.2. Remove 2 screws (K2) and then remove the BottomCover.3. Disconnect 3 flat connecting cables (K3).4. Disconnect the flexible P.C.B. for the optical pickup(K4).5. Disconnect a connector (K5).6. Remove 2 screws (K6) and then remove the MDMain P.C.B.7. Remove the spring (K7).8. Remove 1 screw (K8) and then remove the SideCover.9. Remove 4 cushions (K9) from the bosses of the MDMechanism.Remove the MD Recorder unit according to Steps 1 and 3of the disassembly procedure.I DISASSEMBLY OF MD RECORDER UNITMD分解 MD基板MD外方 （Fig. 6参照）1. （K1） 3本外、 （） 外。2. （K2） 2本外、 （） 外。3. （K3） 3個外。4. 光用基板 （K4） 1個外。5. （K5） 1個外。6. （K6） 2本外、MD基板外。7. （K7） 1個外。8. （K8） 1本外、 （） 外。9. （K9） 4個MD外。分解手順従MD取外。Fig. 6(K3)x2(K2)x12x 2mm(K1)x12x 3mm(K1)x12x 3mm(K1)x12x 3mm(K3)x1(K5)x1(K2)x12x 3mm(K6)x21.7x 3mm(K4)x1(K8)x12x 3mm(K7)x1Top CoverMD MechanismCushionCushionSide CoverMD Main P.C.B.Flexible P.C.B. for optical pickup (*1)Bottom Cover(*1) After pulling off the flexible P.C.B. for the optical pickup from the connector, cover its end with aluminum foil or the like which is electrically conductive so as to prevent the optical pickup from beingdamaged by static electricity.PullPullSpring(K9)x2(K9)x2BossBoss (*1)光用基板 引抜後、静電気光破壊防止、基板先端導電性箔等包。引引（）光用基板 (*1)MD基板（）MD（）MDX-E30010MDX-E300Removal of Magnetic Head (Fig. 7) Once the magnetic head is removed, it will be neces-sary to perform “Confirmation of magnetic headinstallation Position”. (See page 26.)Remove screw (A1).Cautiona. When removing the magnetic head, hold its base anddo not touch the magnetic head itself or the leafspring.b. Place the magnetic head upside down.c. Use special care so as not to cause any damage tothe magnetic head when installing it.Fig. 7(A1)x11.7x 5mmMagnetic HeadLeaf SpringMD Mechanism磁気MDFig. 8Removal of MD Loading P.C.B./Loading Motor (Fig. 8)1. Remove 1 screw (B1).2. Remove 3 hooks (B2) and then remove the MDLoading P.C.B.3. Remove 2 screws (B3) and then remove the LoadingMotor.(B3)x21.7x 3mm(B1)x11.7x 6mm(B2)x2(B2)x1MD Loading P.C.B.Loading MotorMD基板 磁気外方 （Fig. 7参照） 磁気外場合、 磁気取付位置確認必要。 （27参照） （A1） 1本外。注意a. 磁気外、磁気部分持外。磁気部部。b.磁気置場合、裏向置。c.取付時磁気傷十分注意。 MD基板外方（Fig. 8参照）1. （B1） 1 本外。2. 爪 （B2） 3箇所外、MD基板外。3. （B3） 2本外、外。MDX-E300MDX-E30011Removal of Sled Motor/Optical Pickup Head (Fig. 9) Once the MD mechanism switch P.C.B. is removed, itwill be necessary to perform “Adjustment of Lead-inSwitch Position”. (See page 26.) Once the optical pickup head is removed, it will benecessary to perform “Confirmation of magnetic headinstallation Position”. (See page 26.)1. Remove 3 screws (C1) and then remove the sledmotor.2. Remove the Optical Pickup Head.CautionUse care so as not to cause any damage to the gear.(A damaged gear will cause abnormal noise to occurwhile searching.)(C1)x21.4x 4.5mm(C1)x11.4x 5mmSled MotorMD Mechanism P.C.B.Optical Pickup Head光MD基板Fig. 9Removal of Spindle Motor (Fig. 10) Once the spindle motor is removed, it will be neces-sary to perform “Pickup Rating”. (See page 28.)Remove 3 screws (D1) and then remove the SpindleMotor.Cautiona. Be careful not to scratch the gear.(Scratched gear will produce noises during searching.)b.As the turn-table is magnetized, keep foreign objectsfrom being attracted.(D1)x31.4x 3mmSpindle MotorFig. 10 光外方 （Fig. 9参照） MD基板外、 位置 調整必要。 （27参照） 光外、 磁気位置 確認必要。 （27参照）1. （C1） 3本外、外。2. 光外。注意）傷注意。（傷、 時異音発生為） 外方 （Fig. 10参照） 外、 調整 必要。 （29参照） （D1） 3本外、 外。注意a. 傷注意。（傷、 時異音発生為）b