NAD-C565BEE-cd-sm 维修电路原理图.pdf

NADC 565BEECOMPACTDISC PLAYERC 565BEECOMPACTDISC PLAYERSERVICE MANUALRadioFans.CN 收音机爱 好者资料库- 2 -SAFETY INFORMATIONCAUTIONTHIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:-(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.The lightning flash with arrowhead, within an equilateral tri-angle is intended to alert the user of the presence ofuninsulated dangerous voltage within the productsenclosure; that may be of sufficient magnitude to consti-tute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intend-ed to alert the user of the presence of important operatingand maintenance (servicing) instructions in the literatureaccompanying the appliance.CLASS 1LASER PRODUCTRadioFans.CN 收音机爱 好者资料库- 3 -SERVICE SAFETY PRECAUTIONS1. Replacing the fusesCAUTION: FOR CONTINUED PROTECTION AGAINST THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE OF FUSE.Reference NoPart NumberDescriptionFC200 5120-0050+0FUSE T1.6A/250V 5X20FC201, FC202 5120-0018+0FUSE T1A 250V 5X20FC203 5120-0035+0FU T100MA 250VFC204 5120-0018+0FUSE T1A 250V 5X20FC205 5120-1096+0FUSE 0.8A 250V 8X7 ULNOTE: : USA, CANADIAN MODEL ONLY. : EUROPEAN MODEL ONLY.2. Safety check out(Only U.S.A. model)Before returning the product to the customer, make leakage current or resistance measurements to determine that exposed parts are acceptably insulated from the supply circuit.Parts marked with the symbol are critical with regard to the risk of fire and electric shock.Replace only with parts recommended by the manufacturer.CONTENTSDESCRIPTION PAGESPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4REAR PANEL / FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5DISASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8RF PATTERN TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-13PCB LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-23IC BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-33TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-50MECHANISM EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51MECHANISM EXPLODED VIEW PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53EXPLODED VIEW PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54-55PACKING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56- 4 -SPECIFICATIONSGENERAL PARAMETERS Output level - Analog 2.2 0.1 V Optical -22.5 3.5 dBm Coaxial 650 150 mV Frequency response 0.3 dB (ref. 0 dB 20 Hz-1 kHz) 0.5 dB (ref. 0 dB 5 kHz-20 kHz) Total harmonic distortion 90 dB De-emphasis -3.73 to -5.33 dB (ref. 0dB 5 kHz) -8.04 to -10.04 dB (ref. 0 dB 16 kHz) Linearity 0.01 dB (ref. 1 kHz at -3 dB) 0.02 dB (ref. 1 kHz at -6 dB) 0.02 dB (ref. 1 kHz at -10 dB) 0.05 dB (ref. 1 kHz at -20 dB) 0.15 dB (ref. 1 kHz at -60 dB)POWER CONSUMPTION Rated power 18 W (ref. 230V AC 50 Hz; 120V AC 60 Hz) Standby power 1 W (230V version only) 0.7 W (120V version only) Idle power 15 WDIMENSION AND WEIGHT Unit Dimensions (W x H x D) 435 x 285 x 70 mm (Net) 435 x 293 x 86 mm (Gross)* Net weight 4.9 kg Shipping weight 6.3 kg* - Gross dimensions include feet, extended buttons and rear panel terminals.- 5 -1. LINE OUT 2. RS2323. DIGITAL AUDIO IN (OPTICAL)4 DIGITAL OUT (COAXIAL, OPTICAL)5. +12V TRIGGER INPUT6. IR IN7. AC MAINS INPUT1. STANDBY BUTTON 2. STANDBY LED 3. DISC TRAY4. STOP/OPEN5. SOURCE6. SRC7. RANDOM8. REPEAT9. DISPLAY10. SCAN11. USB INPUT12. PLAY/PAUSE/SKIP13. VFD14. REMOTE SENSORREAR PANEL / FRONT PANELREAR PANELFRONT PANEL23456711234567891214131011- 6 -76654312DISASSEMBLY INSTRUCTIONS1. Remove machine screws M 4.0 x 6.0 ( 1 to 4 ) from the side panels. Remove tapping screw 3.0 x 8.5 ( 5 )from the back panel. Refer to Figure No.1. Figure No.12. Pull both sides of the TOP COVER slightly outwards 6 and tilt approx. 35 and then remove in the direction as indicated by the arrow 7 . Refer to Figure No.2. Figure No.2.- 7 -BLOCK DIAGRAM? ?- 8 -WIRING DIAGRAMAC INCD MECHANISMPOWER BoardLED BoardSERVO BoardVFD BoardVOL BoardUSB BoardMAIN BoardTRANSFORMER7013-0550+0part of front panel7013-0601+0 part of front panel7013-0530+0 part of front panelNSPNSP 7013-0570+0 7013-0520+0 7013-0560+0 7013-1280+0 7012-9020+0 7013-0510+0 7013-0600+0 7013-0540+0 7013-049520+0 part of front panel7012-9450+0 CORD-AC UL/CSA 125V 10A - For AH Version7012-9470+0 CORD-AC PWR CE 250V 10A - For C Version- 9 -RF PATTERN TESTINGNAD - C 565BEE PCB TESTING POINTS DIAGRAMTESTING PROCEDURE(1) Load the test disc (Sony Test CD YEDS-7) and set the unit into PLAY mode.(2) Connect the scope to C7 (Pin 81 of IC1) and DGND (C32). Scope setting: Coupling : AC. Vertical sensitivity : 0.2 V/ div. Horizontal time base : 0.5 S/div.(3) Observe the waveform is 1.5V p-p +/-5% and the eye pattern is at its best shape (see FIG. 1).FIG. 1 (a) FIG. 1 (b) Poor eye pattern FIG. 1 (C) Good eye pattern3T4T5T 11TTest Point- 10 -IMPORTANT NOTESINSTRUCTION FOR HANDLING OPTICAL SYSTEM BLOCK PICK-UPElectrostatic breakdown of the laser diode in the optical system block may occur due to a potential difference caused by electrostatic charge accumulated on clothing, human body, etc. A ground must be provided as follows to prevent any electrostatic charge during unpacking or repair work.1. Ground for Human BodyBe sure to wear a ground band (1M ohm) that is properly to remove any static electricity that may be charged on the body.2. Ground for Work BenchBe sure to place a conductive sheet (1M ohm) or copper plate with proper grounding on the work bench or other sur-face on which the pick-up is to be placed.3. Because the static electricity charge on the clothing does not discharge through the body grounding band, do not let clothing to get in contact with the pick-up unit. PRECAUTIONS FOR CHECKING BEAM EMISSIONThe laser beam of this unit is focused on the reflecting surface of the objective lens in the optical system block. Therefore, keep your eyes at least 12 inches (30 cm) away from the objective lens when the laser diode is ON.(Operation Check Method for Laser Diode and Focus Search Function.)When the POWER switch is turned ON after the chucking plate is removed, observe the objective lens and confirm that the following operations are performed properly.(The optical system should be at the lead-in area position when it is checked at this time.)(1) The laser should be at the innermost position after the chucking plate is removed.(2) The diffused light of the laser beam can be seen when the POWER switch is turned ON.(3) Vertical (up and down) movement of the objective lens (2 or 3 times) will take place.INCORRECT CORRECTNOTE: Laser diodes are so susceptible to damage from static electricity that even if a static discharge does not ruin the diode, it can shorten its life or cause it to work improperly.1.Grounding band1M ohm1M ohm2.Conductive Sheet or Copper Plate- 11 -PRECAUTIONS WHEN CHANGING LASER PICK-UPWhen removing the pick-up assembly, short circuit the PCB tracks on the optical block as show in the drawing in order to protect the pick-up before removal.NOTE: Replacement pick-up assemblies are supplied with the PCB pattern already protected.DO NOT REMOVE THE SHORT CIRCUITS UNTIL YOU HAVE FINISHED FITTING THE PICK-UP.Caution:Laser diodes are extremely susceptible to damage from static electricity. Even if a static discharge does not ruin the diode, it can shorten its life or cause it to work improperly. When replacing the pick-up, use a conductive mat, a grounded soldering iron, and so on, to protect the laser diode from static damage.Ground Conductive Wrist Band for BodyGround Line Less than 10 ohmConductive Gum MatSoldering Iron with Ground wireProtective soldering place for laser diode- 12 - MULTI-KEY TABLE FOR C565BEE (original production)ItemContentMulti-key123VFD full segment displaySRC + SCAN BACK Playtime totalRANDOM + SCAN FORWARDEject times countRANDOM + SCAN BACKNOTESNew special key functions (MCU v1.3.8. & Servo v4.4.)-Playtime total counter : Random + Scan Back for 5 sec. -Open tray (Eject times) counter : Random + Scan Back for 5 sec. -Counter reset : Random + Display for 5 sec, then press password 5-4-5-5-6-5 using remote.-Auto-standby on/off : Random + Play for 5 sec. -VFD full segment display : Press SRC + Scan Forward for 5 sec. - 13 - NOTES- 14 -PCB LAYOUTMAIN BOARD - top side- 15 -MAIN BOARD - bottom side- 16 -VOL BOARDtop sidebottom sidetop sidebottom sideUSB BOARDtop sidebottom sideLED BOARDVFD BOARDPOWER BOARDtop sidebottom sidetop sidebottom side- 17 -SERVO BOARDbottom sidetop side- 18 -SCHEMATIC DIAGRAMDACNOTE: 1. RESISTORS, ARE CARBON FILM 5% 1/8W UNLESS OTHERWISE SPECIFIED. 2. CERAMIC CAPACITORS, ARE 50V 10%. UNLESS OTHERWISE SPECIFIED.FOR 545 ONLYOPTIONMute_relay74HUCXX : R458 OK , R457 NC74LVCXX : R458 NC , R457 OKU210 POWER SELECTCUP_REST FOR WM8740WM8741 TO GNDCUP_REST FOR WM8740WM8741 TO GNDFOR ESDNSR=0.1- 15Mb/s (TOXX141X ) use 3V3others use 5VOPTICAL POWER SELECTIf use buffer option1LRCLK2DIN/DINL3BCLK4FSWL/DINR5MCLK6DIFFHW7DGND8DVDD9AVDDR10AGNDR11VMIDR12VOUTRP13VOUTRN14AGND15AVDD16VOUTLN17VOUTLP18VMIDL19AGNDL20AVDDL21ZFLAG22OSR/DSDR23IWO/DOUT24MODE/LRSEL25MUTEB/SDOUT26SDIN/DEEMPH27SCLK/DSD28CSB/SADDR/I2SU211WM874112C30010uF/25V12C30110uF/25V12C30210uF/25V12C30310uF/25V12C30410uF/25V12C30510uF/25V12C306220uF/16V12C307220uF/16V12C308220uF/16V12C309220uF/16V12C311100P12C312100P12C313100uF/16VC314104C315104C316103C317103C318103C31933PC32033P12C321100uF/16VC322104C323104C324104C325104C326104C327104C328104C329104C33010412C331100PC332102C333150PC334104C335150PC336102C337103C338104C339104L212600R/100MHzL213600R/100MHzR37122RR437NC/22RR37322RR374NC/22RR37510KR3761K/NCR377NC/0RR37810K2-3+1U212-AOPA21342-3+1U213-AOPA213484U212-COPA21346-5+7U212-BOPA21346-5+7U213-BOPA213484U213-COPA2134R3795K6R3805K6R3817K5R3827K5R3833K3R3843K312C340100PC341102C342150PC343150PC344102R3855K6R3865K6R3877K5R3887K5R3893K3R3903K3R3915K1R3925K1R3932K4R3942K4R39510KR3962K7R39747RR3982K7R39947RR40010KR40147KR40247KR40347RR40447R1234RCA201RCA2PQ214BC846BQ215BC846BR405100RR406100RQ216BC846BQ217BC846BR4071KR4081KR4091KR4101KC361104C36010412C239100uF/16VC240104C24110412C242470uF/16V1RX1+2RX1-3RX2+4RX2-5RX3+6RX3-7RX4+8RX4-9VCC10AGND11LOCK12RXCKO13RXCKI14MUTE15RDY16DGND117VDD1818CPM19CS(A0)20CCLK(SCL)21CDIN(A1)22CDOUT(SDA)23INT24RST25MCLK26GPO127GPO228GPO329GPO430DGND231TX-32TX+33VDD3334AESOUT35BLS36SYNC37BCKA38LRCKA39SDINA40SDOUTA41NC42VIO43DGND344BGND45SDOUTB46SDINB47LRCKB48BCKBIC205SRC4382R30210RC278104C279104R304120R3VOUT2GND1VCCD221Optical_inC28110412C2821uF/50VR30510RC283104C28010412C28410uF/25VC285104C286104L208600R/100MHzR3062K7R30722R12C28710uF/25VC288104C289104L209600R/100MHzL210600R/100MHzR30822RR30922RR31022R12C29010uF/25VC291103R3112KR3122K7R3132.7KR3142K7R3152K7R316NC/2.7KR3190RR320100R/NCR32110RR3220RR323150RR324150RC29222PC293104R32510R12C2941uF/50V12RCA200RCA1P1VIN3GND2VCCD222Optical_outC29510412C29610uF/25VC297104R3260RR33210KR333100KR3341MR3351M12D2231N414812D2241N4148R336470RR337100K12C2981000uF/16V12C29947uF/16V123D225BAT54123D226BAT5412C207100uF/16VC208104C20910412C21047uF/16VR2335K6R2345K6R213NC/220RR23022RR23122RR216NC/0RR21722RR21822RR21922RR22010KR22110KR22210KR22310KR22422RR23210K1LRCLK2DIN/DINL3BCLK4FSWL/DINR5MCLK6DIFFHW7DGND8DVDD9AVDDR10AGNDR11VMIDR12VOUTRP13VOUTRN14AGND15AVDD16VOUTLN17VOUTLP18VMIDL19AGNDL20AVDDL21ZFLAG22OSR/DSDR23IWO/DOUT24MODE/LRSEL25MUTEB/SDOUT26SDIN/DEEMPH27SCLK/DSD28CSB/SADDR/I2SU200WM874112C21110uF/25V12C21210uF/25V12C21310uF/25V12C21410uF/25V12C22110uF/25V12C22210uF/25VC223104C224104C225104C226104C227104C228104C229104C231104C234104L201600R/100MHzL202600R/100MHzR25422RR435NC/22RR25722RR258NC/22RR25910KR2601K/NCR261NC/0RR26310KR2645K6R2655K6R26822RR26922RR27022RR27110KR27222RQ201BC846B12D2011N4148R2251k213Q203BC856B213Q207BC856B12D215NC/1V8_1.3W11H112C36510uF/25V1OUT2GND3IN4OUTIC201LM1117-1.81OUT2GND3IN4OUTIC203LM1117-3.3LH12345678910RL207R434NC/0RR25522RR436NC/0RR37222RR438NC/0RR439NC/0RR44022RR44122RR442NC/22RR443NC/22RR4442K7R445NC/0R4VCC2GND1EN3OUTU22024.576MHzC364104R3284K7R4462K7Q219BC846BR4472KR45110KC370104C371104C372104L214600R/100MHzR4482KC373104C37410PR4560RR4580RR457NC/0RC375104R4550R12L22133uH12L21733uHC382104R463NC/0RC383470PC384470PC387104C390224 wilaC389224 wimaR471NC/47RR472NC/47R546IC213-B74HC125546U210-B74HC1259108U210-C74HC125121311U210-D74HC125R3180RR3170RR211NC/10RR212NC/10RR4740RR47510R/NCR476100R/NCR478100R4VCC2GND1EN3OUTU21724.576MHz4VCC2GND1EN3OUTU21822.5792MHz213IC213-A74HC125Q223BC846BR4490RR4500RC392100P/NC12D232UF4002C396104213U210-A74HC125R482100R/NC1P1DGND1P2VCCA1P3OPIN1P4VCCB1P5OPOUT1P6DGNDR483100R/NCC397100P/NCC398100P/NC1PIN51PIN6R484NCR485100K/NCR486100K/NCLRCLKDATABCLKMCLKDVDD_3V3DAC_5VDGNDDAC_5VDAC_5VDVDD_3V3CUP_RESTDGNDDVDD_3V3+12V-12V+12V-12VMUTE+12V-12V+12V-12VDVDD_3V3D+5VDGNDDGNDDGNDD+5VDVDD_3V3MCLKOUTDVDD_3V3DGNDDGNDBCLKLRCLKDATEOUTDGNDDVDD_1.8VSCLSDASCR4382_INTCUP_RESTDVDD_3V3SPDIFDGNDD+5VDGNDDVDD_3V3DGNDDGNDDVDD_3V3MUTE_-12VDGNDD+5VMUTEDVDD_1.8VD+5VDGNDLRVOUTLN1VOUTLP1VOUTRN2VOUTRP2WM874X_CS2WM874X_CLKEMPH_MDDVDD_3V3CWBIWOLRCLKDATABCLKMCLKDVDD_3V3DAC_5VDGNDDAC_5VDAC_5VDVDD_3V3CUP_RESTDGNDDVDD_3V3VOUTRN1VOUTRP1WM874X_CSWM874X_CLKEMPH_MDCWBIWODGNDD5V6MUTELRSRC_LOCKVOUTRN2VOUTLP2VOUTLN2VOUTRP2VOUTLP1VOUTLN1VOUTRP1VOUTRN1MCLKDATADATEOUTMCLKOUTDATEOUTMCLKOUTMCLKDVDD_3V3CLK_SELDGNDDGNDMCLKDVDD3DVDD3DGNDDA_MUTEDA_MUTEDA_MUTEMUTEDVDD3U5VG4382G4382G4382DVDD_3V3DVDD_3V3DGNDDGNDDGNDDVDD_3V3DVDD_3V3- 19 -MCU, RS232, TRIGGER IN, IR I