Marantz-DV6200-cd-sb 维修电路原理图.pdf

Approved by S.NAGAO Written by WQ-19 2 817/additional rule 3 (1st Issue 2003-03-19)Date:15-May.-2003Model:DV4200,DV6200,VC5200Page:1 / 1REF.NBR:MZ02-037Circulation:Application:Subject:Int.ref:PHENOMENON1. Can not playback by the some encoding software of the MP3 disc.2. The black color of the video output is light.3. Can not playback DVD disc ”WALT DISNEY ATLANTIS.(Only U.S.A. ”/U1B” version occurs)SOLUTIONUpdate firmware version to Ver.2.11MP and over Firmware Update ProcedureDV4200 and DV6200-Refer to service manuals 2-8 pages “How to upgrade by upgrade DISC”.VC5200-Refer to SERVICE BULLETIN MZ01-023 (22-Nov-01)NECESSARY PART Update firm ware (Ver2.21MP) Disc Part no. *DV4200CD3 REMARKSThe countermeasure apply to this claim only.This solution has already been applied in the production line afterthe week code number “MZ000206xxxxxx” and after.The week code number are printed in the serial number label on the rear panel.(ex.MZxx0206xxxxx)SERVICE BULLETIN Problem with playability of MP3 Disc and can not playback DVD disc ”WALT DISNEY ATLANTIS.x for information customercomplaint in case of servicemandatory. See BelowRadioFans.CN 收音机爱 好者资料库Approved by H.TAMURA Written by K.ONOWQ-19 2 817/additional rule3 (1st Issue 2003-03-19)Date:15-May-2003ModelDV4200/DV6200Page:1/1REF.NBR:MZ02-025Circulation:Application:Subject:Int.ref: PHENOMENON1) Sound skips and picture freeze 1 second at the chapter 8 with DVD disc “Beauty and Beast”.2) Subtitle will be ON automatically at the chapter 3 with DVD disc “SPY GAME”.3) Subtitle will be ON automatically at the 1700” with DVD disc “The World is not Enough”.SOLUTIONUpdate the firmware version to Ver.2.21MP. The way of firmware version up is as follows;Connect the DVD player to TV and operate by using Remote Controller 1) Insert the update disc (Part No. *DV4200CD3) into the product.2) FLD indicates PrESS UP when the disc is detected.3) Press ?(up) button.4) FLD indicates rEAd 0 . If FLD indicated rEAd 1 or other number, please refer to the following .5) FLD indicates UPgrAdE 0 . After few minutes, FLD indicate FInISHEd and the tray will be opened automatically.6) Remove the disc. Press OPEN/CLOSE button and the power will be turned off automatically.7) The product should be confirmed the firmware version and be reset.8) Press POWER button and press SETUP button.9) Select “TV aspect” and press ?(right) button.10) Press ?(up) button or ?(down) button and choose “16:9 wide”. Attention : Do not press SELECT/ENTER button ( Keep green triangle mark ) If check mark is appeared, press ?(right) button and change to green triangle mark.11) Enter the code number 1397139 by Numeric buttons.12) Press SELECT/ENTER button. The connected TV indicates “SYSTEM INFORMATION” Please check “MICOM-VER” is 2.21MP. If other number indicate, need to retry this procedure again.13) Press POWER button and turn off the power. Update firmware and Reset are succeeded. During reading the update disc, error messages are as follows Error Num = 1 3 You can retry to upgrade by disc. Because, flash ROM is not erased data yet. Error Num = 4 It is very worst case. The flash ROM is broken during erasing or programming. You need to rewrite from hardware (PC) for using another jig.REMARKThis improvement has been done in the production line after the production week code number “0250” and later. Theproduction week code is mentioned in the serial number label on the rear panel. (ex. MZxx0250 xxxxxx)SERVICE BULLETIN Improvement for playability of DVD disc “Beauty andBeast” and subtitle problem with some discx for informationcustomer complaintin case of servicemandatory. BeforeMZxx0249xxxxxxSYSTEM INFORMATIONMODEL : DVxxxx/xxxREGION-NO :1CHIP-ID :PANTERA IISERVO-VER :b003MICOM-VER :V2.21 MPPROM OPTION :XX XX XX XX XX XXFactory Reset.DoneExample indicatedRadioFans.CN 收音机爱 好者资料库