Infinity-PS210-sub-sm 维修电路原理图.pdf

PS Series PS Series PS210 Subwoofer PS210 Subwoofer SERVICE MANUAL Infinity Systems, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 8/2007 RadioFans.CN 收音机爱 好者资料库 - CONTENTS - BASIC SPECIFICATIONS .1 DETAILED SPECIFICATIONS.2 PACKAGING.4 CONTROLS AND CONNECTIONS.5 OPERATION.7 EXPLODED VIEW/PARTS LIST .8 TEST SET UP AND PROCEDURE.9 BLOCK DIAGRAM.10 ELECTRICAL PARTS LIST (120v) .11 PCB DRAWINGS.14 SEMICONDUCTOR PINOUTS.16 SCHEMATICS (120v).17 Basic Specifications PS210 Powered Subwoofer Frequency Response: 27Hz 150Hz (3dB) Maximum Amplifier Output: 300 Watts RMS; 500 Watts Peak (20Hz 150Hz with no more than 0.1% THD) Crossover Frequencies: 50Hz 150Hz, 24dB/octave, continuously variable Driver: 10 (254mm) MMD Dimensions (H x W x D): 15-3/4 x 12-1/2 x 16-1/2 (with grille) (400mm x 318mm x 419mm) Weight: 38.6 lb (17.6kg) Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice. 1 PS series PS210 subwoofer RadioFans.CN 收音机爱 好者资料库Primus PS210150W Powered Sub Amp LINE VOLTAGEYes/NoHi/Lo LineNom.UnitNotesUS 120vac/60HzYes108-132120VrmsNormal OperationEU 230vac/50-60HzYes207-253230VrmsNormal operation, MOMS requiredParameterSpecificationUnitQA Test LimitsConditionsNotesAmp SectionType (Class AB, D, o her)Dn/an/aLoad Impedance (speaker)4Ohmsn/aNominalRated Output Power (120VAC)150Watts145Domestic version only 120 VAC-60 HzRated Output Power (230VAC)150WattsEU Version only 230 VAC-50-60 HzAVG RMS Dynamic Power210Watts200Average RMS power, 3/20 Cycles 50 Hz, Driven6dB above its input sensi ivity sensitivity, average of the first 4 consecutive peaksTHD Rated Power0.5%122K filterTHD 1 Watt0.2%0.322K filterDC Offset10mV-DC30Sub amp outputDamping factor50DF35Measured at amplifier board Measured at the speaker cable. 150 Watts THD LP T 15 MinutesPower on Delay time3sec.4AC Power AppliedTransients/PopsATO Transient0.5V-peak0.5V Sub amp outputAmplifier ac ivated by signal presence at the Line inputTurn-on Transient0.5V-peak0.8V Sub amp outputAC Line cycled from OFF to ON PS series PS210 subwoofer 2ParameterSpecificationUnitQA Test LimitsConditionsNotesTurn-off Transient0.5V-peak0.8V Sub amp outputAC Line cycled from ON to OFFEfficiencyEfficiency60%58Test conducted at rated power 150WNominal Line voltage Efficiency at 1/8 of rated power38%37Test conducted at 18.75 WRMSNominal Line voltage-Rated impedance 4 OhmsOff state input power16Watts18Nominal Line voltage RED LEDStand-by Input Power24Watts26 nom. line voltageMaximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation.LED GREEN no signal appliedPower Cons. rated power250Watts260 nom. line voltage150 Watts 4 Ohms nominal line voltageProtectionsShort Circuit Protection YESfunctional Direct short at outputAmplifier should resume opera ion after short circuit condition removal Thermal Protection YESfunctional1/8 max unclipped Power at 1.06 times the input voltageTemperature rise in accessible metal parts should not exceed 35K rise for domestic version or 30K rise for European versions (refer to requirements sheet).DC Offset ProtectionYES-DC present at Speaker Out leadsDesign must insure no Offset at the speaker output under any operating condition including abnormal operationLine Fuse RatingUSA-Domestic 2Amps2Type-T or Slo Blo-250 VInternal fuse with UL/SEMKO rated holderEU1.25Amps1.25Type-T or Slo Blo-250 V, Low Breaking capacityInternal fuse with UL/SEMKO rated holder PS series PS210 subwoofer 34 PS series PS210 subwoofer Rear PanelCONTROLS ANDCONNECTIONSCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCROSSOVERFREQUENCYLEVELLINE LEVEL INPHASEMinMaxLRFor LFE use L or RGreen: OnRed: Standby50Hz080Hz150HzPOWERONLFENORMAL180120V60HzOFFWARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTUREAVERTISSEMENT: POUR PRVEN R LES RISQUES DINCEND E OU DE CHOC LECTRIQUE VITER DEXPOSER CET APPARE LA LA PLUIE OU A LHUMID TNRTL/CCSA 22 2UL1492Subwoofer-Level Control LFE/Normal SelectorPhase SwitchCrossover AdjustmentLine-Level/LFE Input Power Switch Status LED 5 PS series PS210 subwoofer SYSTEMCONNECTIONSIf your receiver/processor doesnot contain a Dolby Digital or DTS processor but has subwoofer outputs:Set line-level/LFE switch to“Normal.”NOTE: If your receiver/processorhas only one sub out,you may useeither the L or R input.If you have a DolbyDigital orDTSreceiver/processor with alow-frequency effects (LFE) orsubwoofer output:LRCROSSOVERFREQUENCYLEVELLINE LEVEL INPHASEMinMaxLRFor LFE use L or RGreen: OnRed: Standby50Hz080Hz150HzLFENORMAL180SUBWOOFER ORLFE OUTPUTCROSSOVERFREQUENCYLEVELLINE LEVEL INPHASEMinMaxLRFor LFE use L or RGreen: OnRed: Standby50Hz080Hz150HzLFENORMAL180Set LFE/Normal switch to “LFE.” 6 PS series PS210 subwoofer OPERATIONPower OnPlug your subwoofersAC cord into a wall outlet.Do not use the outlets on the back of the receiver.Initially set the Subwoofer-Level Control to the “min”position.Turn on your sub by pressing the Power Switch on the rear panel.Turn on your entire audio system and start a CD or movie soundtrack at a moderate level.Auto On/StandbyWith the Power Switch in the ON position,the Status LED on the back panel will remain lit in red or green to indicate the On/Standby mode of the subwoofer.RED = STANDBY (No signal detected,Amp Off)GREEN = ON (Signal detected,Amp On)The subwoofer will automatically enter the Standby mode after approxi-mately 10 minutes when no signal is detected from your system.The subwoofer will then power ON instantly when a signal is detected.Duringperiods of normal use,the Power Switch can be left on.You may turnoff the Power Switch for extended periods of nonoperation,e.g.,whenyou are away on vacation.Adjust GainTurn your Subwoofer-Level Control up to the halfway position.If nosound emanates from the subwoofer,check the AC-line cord and inputcables.Are the connectors on the cables making proper contact? Is the AC plug connected to a “live”receptacle? Has the Power Switch been pressed to the “On”position? Once you have confirmed that the subwoofer is active,proceed by playing a CD,record or cassette.Use a selection that has ample bass information.Set the overall volume control of the preamplifier or stereo to a comfort-able level.Adjust the Subwoofer-Level Control until you obtain a pleasing blend of bass.Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entiremusical range.Many users have a tendency to set the subwoofer volumetoo loud,adhering to the belief that a subwoofer is there to produce lotsof bass.This is not entirely true.A subwoofer is there to enhance bass,extending the response of the entire system so the bass can be felt aswell as heard.However,overall balance must be maintained or the musicwill not sound natural.An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but is never obtrusive.Phase ControlThe Phase Switch determines whether the subwoofer speakers piston-like action moves in and out with the main speakers,0,or oppositethe main speakers,180.Proper phase adjustment depends on several variables such as room size,subwoofer placement and listener position.Adjust the phase switch to maximize bass output at the listening position.Crossover AdjustmentThe Crossover Adjustment Control determines the highest frequency atwhich the subwoofer reproduces sounds.If your main speakers can comfort-ably reproduce some low-frequency sounds, set this control to a lowerfrequency setting, between 50Hz and 100Hz.This will concentrate thesubwoofers efforts on the ultradeep bass sounds required by todaysfilms and music.If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies,set the Crossover Adjustmentcontrol to a higher setting,between 120Hz and 150Hz.NOTE: This control will have no effect if the LFE/Normal Selector is setto LFE.If you have a Doby Digital or DTS processor/receiver,the Low-PassFrequency is set by the processor/receiver.Consult your owners manual to learn how to view or change this setting. 7 PS series PS210 subwoofer PS series PS210 subwoofer 8 PS210 sub Test Set Up and Procedure SYSTEM AURAL SWEEP TEST Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables General Unit Function (UUT = Unit Under Test) Switches/knobs on the amplifier faceplate: Crossover Frequency Adjust full CW (Max) Phase switch either position Normal/LFE switch - Normal 1. From the signal generator, Connect both right and left line level inputs (RCA jacks) to signal generator and UUT. Use Y-cable if necessary from mono source. 2. On the amplifier, turn the LEVEL control full Counterclockwise (Min). 3. Turn on generator, adjust to 75mV, 50 Hz. 4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max). 5. LED (on amp panel) should now be Green; immediate bass response should be heard and felt from rear port tube opening. Sweep Function 1. Follow steps 1-5 above, using a sweep generator as a signal source. 2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofer and test. Driver Function (Woofer) 1. Remove woofer from cabinet; detach + and - wire clips. 2. Check DC resistance of woofer; it should be 3.4 ohms10%. 3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. 9 PS series PS210 subwoofer 10 PS series PS210 subwoofer PS210 Electrical Parts ListPart number Qty DescriptionReference DesignatorPREMAP/MAIN/POWER PCBCapacitors034-330525-300ZR1GR Electrolytic cap. 33uF/25V M (R)0511 P:5C1033-680464-270ZS1GS NPE Cap. 印ELYTONE 6u8/100V K10 (R)1020 GNEC72032-100484-200ZS1GS END Mylar cap. 1uF/250V K P:15C70,033-470464-270ZS1GS NPE Cap.(印ELYTONE)1K 4u7/100V K10 (R)1015 GNEC73031-100343-100ZS1GS SMD Cap. 100pF/50V J 0805 NPO C58034-220525-301ZS2GS Electrolytic cap. 22uF/25V M (R)5x11 P:5 C50,53031-560243-100ZS2GS SMD Cap. 56pF/50V J 0805 NPO C57,61031-220243-103AZ1GS SMD Cap. 0u022/50V J 0805 X7R C84,031-100344-100ZS17 GS SMD Cap. 0u1/50V K 0805 X7R C42-44,46-49,52,55,60,63,71,74,77,100,101,80031-100244-100ZS4GS SMD Ceramic cap. 0u01/50V K 0805 X7R C45,51,66,67,034-470515-307ZR1GR Electrolytic cap.LOW ESR 85 47uF/16V M (R)0511 P:5 C65031-100344-100ZS1GS SMD Cap. 0u1/50V K 0805 X7R C54034-100625-300ZS1GS Electrolytic cap. 100uF/25V M (R)6.3x11 P:5C64031-470244-102ZS2GS SMD Cap. 0u047/50V K 0805 X7R C62,59031-560343-102ZS1GS SMD Cap. 560pF/50V J 0805 NPO C56034-330615-300ZS1GS Electrolytic cap. 330uF/16V M (R)0812 P:5 C78031-100344-100AZ2GS SMD Cap. 0u1/50V K 0805 X7R C81,82035-100393-301ZR2GR Mylar cap.(ESK TYPE) 0u1/63V J P:5 PN:ESK063S10JTC28,2A,035-220393-300ZR1GR PE Cap. 0u22/63V J P:5 C27,034-470415-301ZS1GS Elect. Cap. 4u7/50V M (R)0511 P:5 C2034-100525-300ZS3GS Electrolytic cap. 10uF/25V M (R)0511 P:5 C35,237,238,031-100244-100ZS2GS SMD Ceramic cap. 0u01/50V K 0805 X7R C5,10031-100343-100ZS2GS SMD Cap. 100pF/50V J 0805 NPO C16,36031-100344-100ZS1GS SMD Cap. 0u1/50V K 0805 X7R C11031-100384-100RZ2GS SMD Cap. 0u1/250V K 1206 X7R C3,7031-220243-103AZ1GS SMD Cap. 0u022/50V J 0805 X7R C40031-220344-100ZS5GS SMD Cap. 220pF/50V J 0805 NPO C14,15,20,21,19031-330244-100ZR1GR SMD Cap. 0u033/50V K 0805 X7R C33,031-680444-102ZR2GR SMD Cap. 6800pF/50V K X7R 0805 C32,34,032-270343-301ZS3GS Mylar cap. (MP) 0u27/63V J P:5 C29,26,25032-820244-200ZR1GR Mylar cap. 0u082/100V K (R)C30034-220515-302ZR2GR elect. Cap. 22uF/16V M (R)0511 P:5 C39,75034-220525-301ZS4GS 22uF/25V M (R)5x11 P:5 C4,9,41,76034-330615-300ZS1GS 330uF/16V M (R)0812 P:5 C12034-330780-300ZR2GR 85 SNAPIN 3300uF/80V M (R)22x48C6,8034-470515-200ZR1GR 47uF/16V M (R)0511 P:2.5C37039-100384-100ZR1GR Safety cap. (0u1/250V) .1K275VACx2 18x6x12mmCXAC1034-100615-301ZS1GS electrolytic cap. 100uF/16V M (R)0611 P:5 C83031-100344-100ZS2GS SMD Capacitor 0u1/50V K 0805 X7R C102,103,031-100444-104ZR1GR SMD Capacitor 1000pF/50V K 0805 X7R C104Resistors024-100398-120ZR1GR SMD Resistor 100R 1/8W J 0805 R62020-220497-120ZR1GR Carbon Resistor 2K2 1/4W J R11024-100298-120ZR2GR SMD Resistor 10R 1/8W J 0805 R81,82021-100401-120ZR1GR MOF Resistor 1K 1W J INK MO-100R103024-470498-120ZR2GR SMD Resistor 4K7 1/8W J 0805 R85,86022-500003-020ZR1GR Resistor KNP 0R05 3WS J FK TYPER104024-220798-120ZR1GR SMD Resistor 2M2 1/8W J 0805 R80024-430498-120ZR1GR SMD 4K3 1/8W J 0805 R78024-300498-120LZ1GR SMD 3K 1/8W J 0805 R105,024-470598-120ZR1GR SMD 47K 1/8W J 0805 R107024-220598-120ZR1GR SMD 22K 1/8W J 0805 R118,024-680498-120ZR6GR SMD 6K8 1/8W J 0805 R91024-110598-100ZR1GR SMD 11K 1/8W F 0805 R98024-200598-120ZR1GR SMD 20K 1/8W J 0805 R94024-100698-120ZR2GR SMD 100K 1/8W J 0805 R3,112024-100598-120ZR18 GR SMD 10K 1/8W J 0805 R2,74,75,84,88,89,97,106,113-117,119,120, 141,138,139,11 PS series PS210 subwoofer Part number Qty DescriptionReference DesignatorPREMAP/MAIN/POWER PCB024-100498-120ZR7GR SMD 1K 1/8W J 0805 R79,83,92,95,96,110,145,024-590498-100ZR1GR SMD 5K9 1/8W F 0805 R140,024-270498-120ZR1GR SMD 2K7 1/8W J 0805 R73024-442498-100ZR1GR SMD 4K42 1/8W F 0805 R128024-200498-120ZR1GR SMD 2K 1/8W J 0805 R108024-300598-120ZR1GR SMD 30K 1/8W J 0805 R131,024-150598-100ZR2GR SMD 15K 1/8W F 0805 R132,133,024-470698-120ZR2GR SMD 470K 1/8W J 0805 R129,130,024-390598-120ZR1GR SMD 39K 1/8W J 0805 R77024-470298-120ZR2GR SMD 47R 1/8W J 0805 R101,102024-390498-120ZR1GR SMD 3K9 1/8W J 0805 R93024-220398-120ZR1GR SMD 220R 1/8W J 0805 R90024-470398-120ZR3GR SMD 470R 1/8W J 0805 R76,99,100024-330498-100ZR2GR SMD 3K3 1/8W F 0805 R127,137,024-220498-121ZR2GR SMD 2K2 1/8W J 0805 R1,87,024-162598-100ZR4GR SMD 16K2 1/8W F 0805 R125,126,135,136,024-000098-120ZR1GR SMD Resistor 0R 1/8W J 0805 R68024-100498-120ZR3GR SMD Resistor 1K 1/8W J 0805 R65,44,151,024-100598-100ZR5GR SMD 10K 1/8W F 0805 R146,147,30,31,33,024-100598-120ZR11 GR SMD 10K 1/8W J 0805 R17,19,54,58,63,71,72,111,123,124,134,024-100898-120ZR1GR SMD 10M 1/8W J 0805 R121024-130498-100ZR1GR SMD 1K3 1/8W F 0805 R5A024-150498-120ZR1GR SMD 1K5 1/8W J 0805 R67024-150598-100ZR3GR SMD 15K 1/8W F 0805 R29,024-160698-120ZR1GR SMD 160K 1/8W J 0805 R152,024-220498-121ZR2GR SMD 2K2 1/8W J 0805 R61,57,024-237598-120ZR1GR SMD 23K7 1/8W F 0805 R48024-243498-100ZR1GR SMD 2K43 1/8W F 0805 R36024-270498-120ZR1GR SMD 2K7 1/8W J 0805 R64024-300598-120ZR1GR SMD 30K 1/8W J 0805 R56,024-330498-120ZR8GR SMD 3K3 1/8W J 0805 R7,8,12-15,59,55,024-330598-120ZR2GR SMD 33K 1/8W J 0805 R4,5024-332498-100ZR2GR SMD 3K32 1/8W F 0805 R26,27024-470498-121ZR3GR SMD 4K7 1/4W J 1206 R148-150,024-470598-120