Infinity-PS8-sub-sm 维修电路原理图.pdf

PS-8 PS-8 PS Series SERVICE MANUAL Infinity Systems Incorporated 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 10/2006 RadioFans.CN 收音机爱 好者资料库 CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CONTROLS & CONNECTIONS . . . . . . . . . . . . . . . 3 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . 5 UNIT EXPLODED VIEW. . . . . . . 6 AMPLIFIER EXPLODED VIEW. . . . . . . 7 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 8 PS-8 TEST SET UP AND PROCEDURE . . . . . . . . 9 ELECTRICAL PARTS LIST . . . . . . . . . . 10 PCB DRAWINGS (serial # ME0683-16316 and below). . . . . . 13 PCB DRAWINGS (serial # ME0683-16317 and above) . . . . . . . . 15 IC TRANSISTOR PINOUTS . . 17 SCHEMATIC DIAGRAMS (serial # ME0683-16316 and below). . . .18 SCHEMATIC DIAGRAMS (serial # ME0683-16317 and above). . . . . . .20 SCHEMATIC DIAGRAMS (Rev 2) . . . . . . . . 22 PACKAGE. . .25 PS-8 SPECIFICATIONS Frequency Response: 35Hz 150Hz (3dB) Maximum Amplifier Output: 100 watts RMS (20Hz 150Hz with no more than 0.1% THD) Crossover Frequencies: 50Hz 150Hz, 24dB/octave, continuously variable Driver: 8 (203mm) MMD DCR = 4.3 Dimensions 17-1/2 x 10-5/8 x 16-3/4 (H x W x D) (445mm x 270mm x 426mm) Weight: 33 lb (15kg) Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice. 1PS-8 PS-8 RadioFans.CN 收音机爱 好者资料库INFINITY PRIMUS PS-8 100W Powered Sub/ Plate Amp LINE VOLTAGEYes/NoHi/Lo LineUnitNotesUS 120VAC/60HzYes108-132VrmsNormal OperationEurope 220-240VAC, 50-60HzYes220-240VrmsNormal OperationParameterSpecificationUnitQA Test LimitsConditionsNotesAmp SectionType (Class AB, D, other)AB ABn/aLoad Impedance (speaker)4 Ohmsn/aNominalRated Output Power100 Watts95Single input drivenTHD Rated Power0.5 %122K filterTHD 1 Watt0.1 %0.522K filterDC Offset10 mV-DC50 Speaker OutputDamping factor100 DF50Measured at speaker terminalsOutput power 90 Watts THD 0.1 %Input SensitivityInput Frequency50 Hz50Nominal Freq.Line Input (L&R)171 mVrms2dBTo Rated PowerSingle input driven, AP Zo=600 OhmsLFE Input117 mVrms2dBTo Rated PowerLFE input driven only, AP Zo=600 OhmsSpeaker/Hi Level Inpu2.4 Vrms2dBTo Rated PowerSingle input drivenSignal to NoiseSNR-A-Weighted100 dBA85rel. to rated powerA-Weighting filterSNR-unweighted80 dBr80rel. to rated power22K filterSNR 1W-unweighted60 dBr60rel. to 1W Output22K filterResidual Noise Floor1.5 mVrms2.5Volume max, using RMS reading Residual Noise Floor1mVrms(max)2Volume max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)Input ImpedanceLine input L&R , LFE10 K ohmsn/aNominalSpeaker/Hi Level Inpu4.7 K ohmsn/aNominalFiltersLow Pass (fixed or variable)Variable-2dBSubsonic filter (HPF)Hz2dBLimiter (yes/no)NO-n/aFeaturesLFE Input, Phase Switch, ATOYESfunctional Volume pot Taper (lin/log)LOG-functional Input ConfigurationLine In (L,R)L ,R-functionalRCA inputs: L , R Summed to MonoLine level in LFELFEfunctionalSpkr/Hi Level In (L,R)L,R-functionalL R Summed to MonoSpkr Out: Level out (L,R)Hi Pass Filter120 VAC VersionNO120VAC version is not provided with Spkr. Output connectors230 VAC VersionYESfunctionalThis feature exists in 230VAC ModelDirect by pass from Speaker inSignal Sensing (ATO)Auto-Turn-On (yes/no)YES-functionalATO Input Frequency50 HzfunctionalATO Level2 mVfunctional2mV50Hz into Line Input w/ 1 ch. drivenATO Level Speaker in35 mVfunctional35mV 50 Hz into the speaker input, single input driven.ATO Turn-on time5 msfunctionalAmp connected and AC on, then input signal appliedAuto Mute/ Turn-OFF Time10 minutesfunctionalT before muting, after signal removedAuto turn of time (T) must be 5 T 15Power on Delay time3 sec.functionalAC Power AppliedTransients/PopsATO Transient5 mV-peak10 Speaker OutputsTurn-on Transient50 mV-peak100 Speaker OutputsAC Line cycled from OFF to ONTurn-off Transient50 mV-peak100 Speaker OutputsAC Line cycled from ON to OFFEfficiencyStand-by Input Power12 Watts15 nom. line voltageMaximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation.Power Cons.rated power195 Watts210 nom. line voltage100 Watts 4 Ohms ProtectionShort Circuit Protection YES-functionalDirect short at outputThermal Protection 65 deg. C-functional1/8 max unclipped Power Temperature rise should not exceed 35K riseDC Offset ProtectionYES-functionalDC present at Speaker Out leadsRelay or crowbar (for driver/fire protection)Line Fuse RatingExternal fuse with UL/SEMKO rated holder120 VAC2.5 AmpsType-T or Slo Blo230 VAC1.25 AmpsType-T, Low breaking capacityALL SPECS SHOULD BE MEASURED AT NOMINAL LINE VOLTAGE. PS-8 PS-8 2PS-8Rear PanelCONTROLS ANDCONNECTIONSSubwoofer-Level Control Crossover AdjustmentPhase SwitchLFE InputLine-Level Inputs High-Level Inputs Power Switch+HIGH LEVEL INPUTFUSET 2.5A L 250VTYPEAC120V60HZ200 WattsL RPS-8 PS-8 3If your receiver/processor doesnot have subwoofer outputs forthe left and right channels or anLFE output,connect speakerwire from your receiver/amplifierto your speakers and subwooferusing two sets of speaker wire:PS-8If you have a Dolby* Digital or DTSreceiver/processor with alow-frequency-effects (LFE) or subwoofer output:SUBWOOFER ORLFE OUTPUT+ +OUT INIf your receiver/processor does not contain a Dolby Digital or DTSprocessor but has a subwoofer output:NOTE: Some receivers have one subwoofer output.In that case,it is recommended that you use a Y connector (not included) to maximize performance.+ +OUT INRECEIVER/PROCESSORL RSUBWOOFERCONNECTIONSCHOOSE THESUBWOOFERCONNECTIONTHATISMOSTSUITABLE FORYOURRECEIVER/PROCESSORLOOSEN TERMINALSINSERT BARE END; TIGHTEN TERMINALS1.2.BLACK = NO STRIPE = STRIPE = +RED = +This figure shows how to connect bare wiresto the terminals.RECEIVER/AMPLIFIERFront Speaker Output+HIGH LEVEL INPUTL RPS-8 PS-8 4PS-8OPERATIONPower OnPlug your subwoofersAC cord into a wall outlet.Do not use the outlets on the back of the receiver.Initially set the Subwoofer-Level Control to the “min”position.Turn on your sub by pressing the Power Switch on the rear panel.Turn on your entire audio system and start a CD or movie sound-track at a moderate level.Auto On/StandbyWith the Power Switch in the ON position,the LED on thefront panel will remain lit in red or green to indicate theOn/Standby mode of the subwoofer.RED = STANDBY (No signal detected,Amp Off)GREEN = ON (Signal detected,Amp On)The subwoofer will automatically enter the Standby mode afterapproximately 10 minutes when no signal is detected from yoursystem.The subwoofer will then power ON instantly when asignal is detected.During periods of normal use,the PowerSwitch can be left on.You may turn off the Power Switch for extended periods of nonoperation,e.g.,when you are away on vacation.Adjust LevelTurn your Subwoofer-Level Control up to the “5”position(halfway).If no sound emanates from the subwoofer,check the AC-line cord and input cables.Are the connectors on the cablesmaking proper contact? Is the AC plug connected to a “live”receptacle? Has the Power Switch been pressed to the “On”position? Once you have confirmed that the subwoofer is active,proceed by playing a CD,record or cassette.Use a selection thathas ample bass information.Set the overall volume control of the preamplifier or stereo to acomfortable level. Adjust the Subwoofer-Level Control untilyou obtain a pleasing blend of bass.Bass response should notoverpower the room but rather be adjusted so there is aharmonious blend across the entire musical range.Many users have a tendency to set the subwoofer volume too loud,adhering to the belief that a subwoofer is there to produce lotsof bass.This is not entirely true.A subwoofer is there to enhancebass,extending the response of the entire system so the basscan be felt as well as heard.However,overall balance must be maintained or the music will not sound natural.Anexperienced listener will set the volume of the subwoofer so itsimpact on bass response is always there but never obtrusive.Phase ControlThe Phase Switch determines whether the subwooferspeakers piston-like action moves in and out with the mainspeakers,0,or opposite the main speakers,180.Proper phaseadjustment depends on several variables such as room size,subwoofer placement and listener position.Adjust the phaseswitch to maximize bass output at the listening position.Crossover AdjustmentsThe Crossover Adjustment control determines the highestfrequency at which the subwoofer reproduces sounds.If your mainspeakers can comfortably reproduce some low-frequency sounds,set this control to a lower frequency setting, between 50Hzand 100Hz.This will concentrate the subwoofers efforts on theultradeep bass sounds required by todays films and music.If youare using smaller bookshelf speakers that do not extend to thelower bass frequencies,set the Crossover Adjustment control toa higher setting,between 120Hz and 150Hz.NOTE: This control will have no effect if the LFE Input is used.If you have a Dolby Digital or DTS processor/receiver,the Low-PassFrequency is set by the processor/receiver.Consult your ownersmanual to learn how to view or change this setting.PS-8 PS-8 5 Ref# Description Part Number Qty 1 Grille 244-080-0025 1 2 Screw (Trim Ring) 352-DM04525D597 6 3 Woofer Trim Ring 213-080-00488 1 4 Screw (Woofer) 352-FM04014D609 8 5 8” Woofer 20PR10DAG-FW04 1 6 PS-8 Cabinet Not for sale 1 7 PS-8 Amplifier Not for sale 1 8 Screw (Amplifier) 352-AM04020D210 10 9 Port Tube 249-HIPS-01003 2 10 Foot Pad 320-RUB-00199 4 11 Screw (Foot) 352-CM04025D604 4 12 Feet (Main) 320-ABS-00195 4 13 Logo 316-ABS-00532 1 PS-8 6PS-8 PS-8 7PS-8 8 PS-8 Test Set Up and Procedure SYSTEM AURAL SWEEP TEST Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables General Unit Function (UUT = Unit Under Test) Switches/knobs on the amplifier faceplate: Low Pass Frequency Adjust full CW (150Hz) Phase switch either position 1. From the signal generator, Connect both right and left line level inputs (RCA) not the LFE jack - to signal generator and UUT. Use Y-cable if necessary from mono source. 2. On the amplifier, turn the LEVEL control full Counterclockwise (Min). 3. Turn on generator, adjust to 75mV, 50 Hz. 4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max). 5. LED should now be Green; immediate bass response should be heard and felt from rear port tube opening. 6. Turn off generator, turn LEVEL control fully Counterclockwise (Min), disconnect RCA cable. 7. Connect one pair of speaker cables to one set of High Level input terminals on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 8. Turn on generator and adjust so that speaker level input at the amplifier is 1.5V, 50 Hz. Turn LEVEL control full Clockwise (Max). 9. Green LED should light; immediate bass response should be heard and felt from the port tube opening. Sweep Function 1. Follow steps 7-10 above, using a sweep generator as a signal source. 2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofer and test. Driver Function (Woofer) 1. Remove woofer from cabinet; detach + and - wire clips. 2. Check DC resistance of woofer; it should be 4.5 ohms10%. 3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. PS-8 PS-8 9PS-8 Electrical Parts List (See addendum for serial # ME0683-16317 and above)Part number DescriptionReference DesignatorQtyResistors110- 14122j26 Resistor 1.2K 1/4W 5% CF 26mm R2701110- 10821jk2 Resistor 820 1W 5% 10mm R1321110- 122r2j15 Resistor 2.2 1/2W 5% 15mm R1271113- 50r10j10 Cement resistor 0.1 5W 5%R121,1222114- 03302m0 Semi- fixed resistor 3K 0.3W 20% R1381115- h203b208Variable resistor B20K FREQUENCYVR2021115- h503a104 Variable resistor D16 50K/1 A LEVELVR2011110- 20331jk2 Resistor 330 2W 5% 5mm R1461110- 12472j52 Resistor 4.7K 1/2W 5% CF 52mm R201,R2022110- 14681j26 Resistor 680 1/4W 5% CF 26mmR148,R1512110- 16101j26 Resistor 100 1/6W 5% CF 26mm R1201110- 16102j26 Resistor 1K 1/6W 5% CF 26mm R124,213,214,215,2545110- 16103j26 Resistor 10K 1/6W 5% CF 26mm R134,209,212,216,217,220,221,222,225,226,228,232,235,240,215110- 16104j26 Resistor 100K 1/6W 5% CF 26mm R231,2662110- 16105j26 Resistor 1M 1/6W 5% CF 26mm R143,259,2110- 16123j26 Resistor12K 1/6W 5% CF 26mm R135,139,2273110- 16151j26 Resistor 150 1/6W 5% CF 26mm R2531110- 16152j26 Resistor 1.5K 1/6W 5% CF 26mm R103,123,136,137,141,1426110- 16153j26 Resistor 15K 1/6W 5% CF 26mm R118,145,152,1544110- 16154j26Resistor 150K 1/6W 5% CF 26mm R131,203,204,205,206,2526110- 16181j26 Resistor 180 1/6W 5% CF 26mm R111,1142110- 16183j26 Resistor 18K 1/6W 5% CF 26mm R2621110- 16205j26 Resistor 2M 1/6W 5% CF 26mm R2571110- 16223j26 Resistor 22K 1/6W 5% CF 26mm R128,129,133,238,247,250,255,2338110- 16273j26 Resistor 27K 1/6W 5% CF 26mm R2371110- 16332j26 Resistor 3.3K 1/6W 5% CF 26mm R106,R107,1443110- 16392j26 Resistor 3.9K 1/6W 5% CF 26mm R105,1082110- 16393j26 Resistor 39K 1/6W 5% CF 26mm R1261110- 16470j26Resistor 47 1/6W 5% CF 26mm R112,113,115,1164110- 16471j26 Resistor 470 1/6W 5% CF 26mm R1401110- 16472j26 Resistor 4.7K 1/6W 5% CF 26mm R110,125,130,200,207,258,2607110- 16473j26 Resistor 47K 1/6W 5% CF 26mm R101,219,2513110- 16512j26 Resistor 5.1K 1/6W 5% CF 26mm R210,211,229,2304110- 16563j26Resistor 56K 1/6W 5% CF 26mm R1041110- 14472j26Resistor 4.7K 1/4W 5% CF 26mm R147,1502110- 16682j26 Resistor 6.8K 1/6W 5% CF 26mmR1091110- 16333j26 Resistor 33K 1/6W 5% CF 26mm R2491110- 16182j26 Resistor 1.8K 1/6W 5% CF 26mm R1531110- 16103j26 Resistor 10K 1/6W 5% CF 26mm R301,303,304,308,309,314,340,3448110- 16223j26 Resistor 22K 1/6W 5% CF 26mm R310,3122110- 16273j26Resistor 27K 1/6W 5% CF 26mm R3411110- 16472j26 Resistor 4.7K 1/6W 5% CF 26mm R342,432110- 16474j26 Resisto 470K 1/6W 5% CF 26mm R3071110- 16751j26 Resistor 750 1/6W 5% CF 26mmR311,3132110- 20331jk3 Resistor 330 2W 5% R1491110- 16183j26Resistor 18K 1/6W 5% CF 26mm R3021110- 16560j26 Resistor 56 1/6W 5% CF 26mm R1171110- 16562j26 Resistor 5.6K 1/6W 5% CF 26mmR224,2342116- 164531f26 Resistor 4.53K 1/6W 1% MF26mm R2231PS-8 PS-8 (serial # ME0683-16316 and below) 10Part number DescriptionReference DesignatorQtySemiconductors192- 027c1815gr Transistor 2SC1815GR NPNQ102,111,112,113,118,201,206,2078192- 028a1015gr Transistor 2SA1015GR PNPQ114,1162192- 1672n5551 Transistor 2N5551 NPN Q103,1092192- 1682n5401 Transistor 2N5401 PNPQ104,1102197- 131n4148 Diode 1N4148 26mm D101,103,105,1084199- 15000335 Zener diode 3.3V 1/2W 52mm D102,2132199- 15000625 Zener