Pioneer-VSXLX53-avr-sm 维修电路原理图.pdf

ORDER NO.PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, JapanPIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, BelgiumPIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION20102010 Printed in JapanMASTERVOLUMEINPUTSELECTORSTANDBY/ONVSX-LX53PHONESSLQPENUTDNABAUTO SURR/ALC/STREAM DIRECTADVANCEDSURROUNDSTANDARDSURROUNDMCACC SETUP MICSTEREOSPEAKERSHOME THXUSBCONTROLMULTI-ZONEON/OFFADVANCEDMCACCiPodiPhoneTIDE RENUTTESERPIMDHENTERiPodiPhoneVIDEO CAMERAHDMI 5VSX-LX53RRV4133AUDIO/VIDEO MULTI-CHANNEL RECEIVERVSX-LX53VSX-2020-KTHIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).This service manual should be used together with the following manual(s).ModelTypePower RequirementRemarksVSX-LX53SYXJ5AC 220 V to 230 VVSX-2020-KSYXJ5AC 220 V to 230 VModel No.Order No.RemarksVSX-LX53 VSX-2020-KRRV4134PCB RETRIEVAL DIAGRAMFor details, refer to Important Check Points for good servicing. K-FZV JUNERadioFans.CN 收音机爱 好者资料库2VSX-LX531234ABCDEF1234Important Check Points for Good ServicingIn this manual, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.1. Product safetyPlease conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.1 Use specified parts for repair.Use genuine parts. Be sure to use important parts for safety.2 Do not perform modifications without proper instructions.Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.3 Make sure the soldering of repaired locations is properly performed.When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the example)4 Make sure the screws are tightly fastened.Please be sure that all screws are fastened, and that there are no loose screws.5 Make sure each connectors are correctly inserted.Please be sure that all connectors are inserted, and that there are no imperfect insertion.6 Make sure the wiring cables are set to their original state.Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.7 Make sure screws and soldering scraps do not remain inside the product.Please check that neither solder debris nor screws remain inside the product.8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.9 There should be no spark traces or similar marks on the power plug.When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.a Safe environment should be secured during servicing.When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely. 2. AdjustmentsTo keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.4. CleaningFor parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.3. Lubricants, Glues, and Replacement partsUse grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.5. Shipping mode and Shipping screwsTo protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.RadioFans.CN 收音机爱 好者资料库3VSX-LX5356785678ABCDEFCONTENTS1. SERVICE PRECAUTIONS.51.1 NOTES ON SOLDERING.51.2 NOTES ON REPLACING .51.3 CAUTION.52. SPECIFICATIONS.62.1 SPECIFICATIONS.62.2 PANEL FACILITIES.73. BASIC ITEMS FOR SERVICE .113.1 CHECK POINTS AFTER SERVICING .113.2 PCB LOCATIONS.123.3 JIGS LIST.134. BLOCK DIAGRAM .144.1 OVERALL WIRING DIAGRAM .144.2 BLOCK DIAGRAM FOR AUDIO BLOCK.164.3 BLOCK DIAGRAM FOR DIGITAL MAIN VIDEO BLOCK .184.4 BLOCK DIAGRAM FOR COMPOSITE VIDEO BLOCK .194.5 BLOCK DIAGRAM FOR COMPONENT VIDEO BLOCK.204.6 BLOCK DIAGRAM FOR POWER BLOCK(1) .224.7 BLOCK DIAGRAM FOR POWER BLOCK(2) .245. DIAGNOSIS .265.1 DIAGNOSIS FLOWCHART .265.2 CIRCUIT DESCRIPTION.496. SERVICE MODE.556.1 TEST MODE.557. DISASSEMBLY .577.1 DISASSEMBLY.578. EACH SETTING AND ADJUSTMENT.738.1 HOW TO SAVE AND LOAD THE SETTINGS USING BACKUP FUNCTION WITH USB MEMORY.738.2 HOW TO UPDATE FIRMWARE.749. EXPLODED VIEWS AND PARTS LIST.789.1 PACKING SECTION.789.2 EXTERIOR SECTION .809.3 REAR SECTION.829.4 FRONT SECTION .8410. SCHEMATIC DIAGRAM.8610.1 AUDIO ASSY(1/3)(GUIDE PAGE) .8610.2 AUDIO ASSY(2/3).9210.3 AUDIO ASSY(3/3).9410.4 COMPOSITE ASSY.9610.5 DAC LOW ASSY(1/2) .9810.6 DAC LOW ASSY(2/2) .10010.7 COMPONENT ASSY.10210.8 DIGITAL MAIN ASSY(1/10)(GUIDE PAGE).10410.9 DIGITAL MAIN ASSY(2/10) .11010.10 DIGITAL MAIN ASSY(3/10) .11210.11 DIGITAL MAIN ASSY(4/10) .11410.12 DIGITAL MAIN ASSY(5/10) .11610.13 DIGITAL MAIN ASSY(6/10) .11810.14 DIGITAL MAIN ASSY(7/10) .12010.15 DIGITAL MAIN ASSY(8/10) .12210.16 DIGITAL MAIN ASSY(9/10) .12410.17 DIGITAL MAIN ASSY(10/10) .12610.18 FRONT MIC&VIDEO ASSY.12810.19 FRONT HDMI USB ASSY .13010.20 POWER AMP ASSY(1/2).13210.21 POWER AMP ASSY(2/2).13410.22 PRESTAGE ASSY.13610.23 DISPLAY ASSY .13810.24 PRIMARY ASSY.14010.25 USB REGULATOR ASSY.14210.26 XM REGULATOR ASSY.14410.27 REGULATOR ASSY .14610.28 POWER SW, ENCODER and HEADPHONE ASSYS.14810.29 CONNECT and A-DAC BRIDGE ASSYS .14910.30 D-AUDIO BRIDGE ASSY .1504VSX-LX531234ABCDEF123410.31 D-DAC BRIDGE ASSY.15110.32 POS 1-3 ASSYS .15210.33 BIND L FRONT and BACK, BINDER, BIND DM CABLE, BIND R BACK and FRONT, BIND DISP FFC ASSYS .15311. PCB CONNECTION DIAGRAM .15411.1 AUDIO ASSY .15411.2 COMPOSITE ASSY.15811.3 DAC LOW ASSY.16011.4 COMPONENT ASSY .16211.5 DIGITAL MAIN ASSY.16411.6 FRONT MIC&VIDEO and FRONT HDMI USB ASSYS.16811.7 POWER AMP ASSY .17011.8 PRESTAGE ASSY.17411.9 DISPLAY ASSY.17811.10 PRIMARY ASSY .18211.11 USB REGULATOR and XM REGULATOR ASSYS.18411.12 REGULATOR ASSY.18611.13 POWER SW, ENCODER and HEADPHONE ASSYS .19011.14 CONNECT and A-DAC BRIDGE ASSYS.19211.15 D-AUDIO and D-DAC BRIDGE, POS 1-3 and BIND L FRONT ASSYS.19411.16 BIND L BACK, BINDER, BIND DM CABLE, BIND R BACK/FRONT, BIND DISP FFC and BLUETOOH ASSYS.19612. PCB PARTS LIST .1985VSX-LX5356785678ABCDEF1. SERVICE PRECAUTIONS1.1 NOTES ON SOLDERING1.2 NOTES ON REPLACING1.3 CAUTION For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 oC. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 oC in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron.Do NOT use a soldering iron whose tip temperature cannot be controlled.Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden).The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia.The part listed below is difficult to replace as a discrete component part.When the part listed in the table is defective, replace whole Assy.Parts that is Diffcult to Replase ASSY NAME PCB ASSY Part No. Ref No. FUNCTION Part No. Remarks IC101 MAIN CPU UPD61283F1-407LU2A BGA IC904 HDMI Receiver SII9233ACTU IC with heat-pad IC1204 Digital Video Format Converter 88DE2750 BGA IC1212 DDR2 SDRAM EDE5116AJBG-8E-E BGA IC9506 Ethernet IC LAN9211-ABZJ IC with heat-pad IC9804 Regulator NJM2846DL3-18 IC with heat-pad IC9810 Regulator MM1701WH IC with heat-pad DIGITAL MAIN ASSY AWX9719 IC9811 Regulator NJM2846DL3-33 IC with heat-pad Discharging Please refer to page 57, “Preparations Before Perfoming Diagnosis of the POWER AMP Assy”. Ground Points Please refer to page 58, “Ground Points”. 6VSX-LX531234ABCDEF12342. SPECIFICATIONS2.1 SPECIFICATIONS These specifications are applicable when the power supply is 230 V.Audio sectionRated power output (1 kHz, 6 , 1 %)Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 WCenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 WSurround. . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 WSurround back (Front height/wide). . . . . . 150 W + 150 WRated power output (20 Hz to 20 kHz, 8 , 0.08 %)Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 WCenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 WSurround. . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 WSurround back (Front height/wide). . . . . . 110 W + 110 WTotal Harmonic Distortion. . . . . . . . . . . . . . . . . . . . . . .0.06 % (20 Hz to 20 kHz, 8 , 100 W + 100 W)Guaranteed speaker impedance. . . . . . . .16 to 8 , less than 8 to 6 (setting required)Signal-to-Noise Ratio (IHF, short circuited, A network). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 dBFrequency Response . . . . . . . . . .5 Hz to 100 000 Hz dB (Pure Direct Mode)Input (Sensitivity/Impedance) . . . . . . . . . . . .350 mV/47 kOutput (Level/Impedance)REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 mV/2.2 kTuner SectionFrequency Range (FM). . . . . . . . . . . .87.5 MHz to 108 MHzAntenna Input (FM) . . . . . . . . . . . . . . . . . . 75 unbalancedFrequency Range (AM) . . . . . . . . . . .531 kHz to 1602 kHzAntenna (AM) . . . . . . . . . . . . . . . Loop antenna (balanced)Video SectionSignal levelComposite Video . . . . . . . . . . . . . . . . . . . .1 Vp-p (75 )Component Video. . . . . . . . . . . . . . . . .Y: 1.0 Vp-p (75 ),PB, PR: 0.7 Vp-p (75 )Corresponding maximum resolutionComponent Video. . . . . . . . . . . . . . . . . . .1080p (1125p)(Video convert off)Digital In/Out SectionHDMI terminal . . . . . . . . . . . . . . . . . . . . . 19-pin (Not DVI)HDMI output type. . . . . . . . . . . . . . . . . . . . . . .5 V, 100 mAUSB terminal . . . . . . . . . . . . . USB2.0 Full Speed (Type A)iPod terminal . . . . . . . . . . . . USB, and Video (Composite)ADAPTER PORT terminal . . . . . . . . . . . . . . . . .5 V, 100 mAIntegrated control sectionControl (SR) terminal . . . . . . . . . . . 3.5 Mini-jack (MONO)Control (IR) terminal. . . . . . . . . . . . 3.5 Mini-jack (MONO)IR signal . . . . . . . . . . . . . . . High Active (High Level: 2.0 V)12 V Trigger terminal . . . . . . . . . . 3.5 Mini-jack (MONO)12 V Trigger output type. . . . . . . . . . . . 12 V, Total 150 mARS-232C cable type. . . . . 9-pin, cross type, female-femaleEXTENSION terminal . . . . . . . . . . . . . . . . . . . . .5 V, 150 mANetwork SectionLAN terminal . . . . . . . . . . . . . . . . .10 BASE-T/100 BASE-TXBluetooth ADAPTER (AS-BT100) (VSX-LX53 only)Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 5 VVersion . . . . . . . . . . Bluetooth Specification Ver. 2.0 + EDROutput . . . . . . . . . . . . . . . . .Bluetooth Specification Class 2Estimated line-of-sight transmission distance* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 10 mFrequency range . . . . . . . . . . . . . . . . . . . . . . . . . . .2.4 GHzModulation . . . . . . . . .FH-SS (Frequency Hopping Spread Spectrum)Supported Bluetooth profiles. . . . . . . . . . . . A2DP, AVRCPSupported Codec. . . . . . . . . . . . . . SBC (Subband Codec)Supported contents protection . . . . . . . . . . . . . . . SCMS-TExternal dimensions . . . . . . . . . . . . . . . 30.5 mm (W) x 9.0 mm (H) x 50 mm (D)Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 11 g*The line-of-sight transmission distance is an estimate. Actual transmission distances supported may differ depending on surrounding conditions.MiscellaneousPower requirements . . . . . AC 220 V to 230 V, 50 Hz/60 HzPower consumption . . . . . . . . . . . . . . . . . . . . . . . . . .410 WIn standby . . . . . . . . 0.2 W (HDMI SetupControl : OFF)0.3 W (HDMI Setup Control : ON)Dimensions . . . . . 420 (W) mm x 173 (H) mm x 433 (D) mmWeight (without package)VSX-LX53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 kgVSX-2020-K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 kgNumber of Furnished PartsMCACC Setup microphone (APM7009) . . . . . . . . . . . . . . 1Remote control unit (AXD7592). . . . . . . . . . . . . . . . . . . . . 1AAA size IEC R03 dry cell batteries . . . . . . . . . . . . . . . . . 2iPod cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1AM loop antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Bluetooth ADAPTER (AS-BT100) (VSX-LX53 only) . . . . . 1Power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Quick start guideOperating instructions Note Specifications and the design are subject to possible modifications without notice, due to improvements.Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX and the double-D symbol are trademarks of Dolby Laboratories.Manufactured under license under U.S. Patent #s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos are trademarks of DTS, Inc. Product includes software. DTS, Inc. All Rights Reserved.Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.THX, the THX logo and Select2 Plus are