Sony-RCDW10-rcd-sm 维修电路原理图.pdf

RCD-W10US ModelCanadian ModelSERVICE MANUALCOMPACT DISC RECORDERSony CorporationHome Audio CompanyPublished by Sony Engineering Corporation9-874-152-022003L16-1 2003.12SPECIFICATIONSVer 1.1 2003. 12Model Name Using Similar MechanismNEWCD SectionCD Mechanism TypeCDM66C-30B61BBase Unit TypeBU-30BBD61BOptical Pick-up TypeA-MAX.3Model Name Using Similar MechanismNEWCD-R/CD-RWCD Mechanism TypeCDM65-RBD1SectionBase Unit TypeRBD1Optical Pick-up TypeKRM-220CAADECK A (the CD player section)SystemCompact disc digital audiosystemLaserSemiconductor laser ( =780 nm)Emission duration:continuousFrequency response20 Hz 20,000 Hz (0 5dB)DECK B (the CD-R and CD-RWrecording section)SystemCompact disc digital audiosystemLaserSemiconductor laser ( =780 nm)Emission duration:continuousPlayable discsCD, CD-R, CD-RWRecordable discsCD-R, CD-RW (for musicuse)Frequency response20 Hz - 20,000 Hz (0 5dB)GeneralPower requirementsNorth American model:120 V AC, 60 HzPower consumption25 WDimensions (approx ) (w/h/d) incl projecting partsand control430 108 399 mm( 17 4 3/8 15 3/4 inch)Mass (approx )6 0 kg(13 lbs 4 oz)Supplied accessoriesDesign and specifications are subject to changewithout notice Audio connecting cordsPhono jack 2 (red/white) Phono jack 2 (red/white) (2) Remote commander (remote) (1) Size AA (R6) batteries (2)InputsANALOG IN(Phono jacks)Impedance: 47 kilohmsRated input: 500 mVrmsMinimum input250 mVrmsDIGITAL OPTICAL IN(Square optical connector jack)Optical wavelength:660 nmOutputsANALOG OUT(Phono jacks)Impedance: 47 kilohmsRated output: 2 VrmsLoad impedance: over10 kilohmsDIGITAL OPTICAL OUT(Square optical connector jack)Wavelength: 660 nmOutput level: 18 dBmPHONES(Phono jack)Load impedance: 32 ohmsOutput level: 12mWRadioFans.CN 收音机爱 好者资料库2This appliance is classified as a CLASS 1 LASER product. TheCLASS 1 LASER PRODUCT MARKING is located on the rearexterior.The following caution label is located inside the apparatus.Laser component in this product is capableof emitting radiation exceeding the limit forClass 1.CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiationexposure.Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may bedamaged by heat.Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270Cduring repairing. Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times). Be careful not to apply force on the conductor when solderingor unsoldering.RCD-W10SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONTCRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PISES SONYDONT LES NUMROS SONT DONNS DANS CE MANUEL OUDANS LES SUPPMENTS PUBLIS PAR SONY. After correcting the original service problem, perform thefollowing safety checks before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage. Check leakage asdescribed below.LEAKAGE The AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes).Leakage current can be measured by any one of three methods.1.A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers instructions to use theseinstruments.2.A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.3.Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63Trd are examples ofa passive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2V AC range are suitable. (SeeFig. A)SAFETY CHECK-OUTTo Exposed Metal Parts on Set0.15 F1.5 kACVoltmeter(0.75 V)Earth GroundFig. A. Using an AC voltmeter to check AC leakage.MODEL IDENTIFICATION BACK PANEL Parts No.PARTS No.MODEL4-238-401-54-238-401-6USCanadianRadioFans.CN 收音机爱 好者资料库3RCD-W10TABLE OF CONTENTS1. SERVICING NOTE42. GENERAL53. DISASSEMBLY 63-1. Case (409538) 73-2. Loading Panel (1CD) 73-3. Loading Panel (CDR) 83-4. Front Panel Section 83-5. DISPLAY Board 93-6. CDR Mechanism Deck (CDM65-RBD1) 93-7. Tray 103-8. CDR Board 103-9. Holder (MG) Sub Assy, Dust Cover 113-10. Optical Pick-Up (KRM-220CAA)113-11. Motor Assy (Loading)(M201) 123-12. Cam (CH) 123-13. CD Mechanism Deck (CDM66C-30B61B)133-14. Tray (66) 143-15. BD Board 153-16. Optical Block Section 153-17. MAIN Board164. TEST MODE 185. ELECTRICAL ADJUSTMENTS21CD SECTION. 21CD-R/RW SECTION.226. DIAGRAMS536-1. Block Diagrams CD-R Section 54 CD Section 55 POWER/DISPLAY Section 566-2. Printed Wiring Board BD Section 576-3. Schematic Diagram BD Section 586-4. Printed Wiring Board CD-R Section (Side A) 596-5. Printed Wiring Board CD-R Section (Side B) 606-6. Schematic Diagram CD-R Section (1/4) 616-7. Schematic Diagram CD-R Section (2/4) 626-8. Schematic Diagram CD-R Section (3/4) 636-9. Schematic Diagram CD-R Section (4/4) 646-10. Printed Wiring Board MAIN Section (Side A) 656-11. Printed Wiring Board MAIN Section (Side B) 666-12. Schematic Diagram MAIN Section (1/2) 676-13. Schematic Diagram MAIN Section (2/2) 686-14. Printed Wiring Board DISPLAY Section 696-15. Schematic Diagram DISPLAY Section 706-16. IC Block Diagrams 716-17. IC Pin Function Description 747. EXPLODED VIEWS847-1. Case Section847-2. Front Panel Section 857-3. Chassis Section 867-4. CDR Mechanism Deck Section (CDM65-RBD1)877-5. CD Mechanism Deck Section (CDM66C-30B61B) 887-6. Base Unit Section (BU-30BBD61B) 898. ELECTRICAL PARTS LIST90Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.) : LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher thanordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful! Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc. Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.4RCD-W10SECTION 1SERVICING NOTENOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepain parts.The flexible board is easily damaged and should be handled withcare.NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.The emission check enables continuous checking of the S curve.LASER DIODE AND FOCUS SEARCH OPERATIONCHECKCarry out the “S curve check” in “CD section adjustment” and checkthat the S curve waveform is output three times.MessageC12/Cannot CopyC13/Rec ErrorC14/TOC ErrorC41/Cannot CopyC71/Din UnlockExplanationYou are trying to record a disc thatcannot be played back in DECK-Aor with an external device, such asCD-ROM or VIDEO CD. Remove the disc, and then insert amusic CD for playback.Recording has not been completedsuccessfully because of vibration. Relocate the unit in a place free ofvibration and restart the recordingagain.The disc you try to record isexcessively dirty (such as oil-stained or finger marked) orscratched. Or the disc is notnormal. Replace the disc with another oneand restart the recording again.The unit did not read the TOCinformation. Insert other discs.The sound source you are trying torecord is a copy of a commercialmusic software. Or you are tryingto record on a CD-R/CD-RWdigitally. Because of the restriction of theSerial Copy Management System,you cannot record a copy of acommercial music software.Neither can you record a CD-R/CD-RW digitally.If this message is displayedmomentarily, this is not an error. Itis caused by the digital signalduring recording.During recording of a digital soundsource, the connecting cable hasbeen disconnected or the player ofthe sound source has turned off. Connect the cable or turn on thedigital player.Self-diagnosis FunctionWhen the self-diagnosis function is activated toprevent the player from malfunctioning, threecharacter service numbers in a combinationwith a message appears in the display. In thiscase, check the following table.5RCD-W10SECTION 2GENERAL3641 25978q;qaqsqdqfqgqhqjqkqlw;wdwawfwjwke;wlwgwhws1 POWER button2 H button3 OPEN/CLOSE A button4 CD SYNCHRO NORMAL button5 CD SYNCHRO HIGH button6 OPEN/CLOSE A button7 H button8 INPUT button9 FINALIZE buttonq; ERASE buttonqa SBM button and indicatorqs REC z buttonqd X buttonqf REC LEVEL knobqg x buttonqh PLAY MODE buttonqj TIME buttonqk DISPLAY buttonql YES buttonw; l AMS L knobwa CLEAR buttonws MENU/NO buttonwd l AMS L knobwf CLEAR buttonwg PLAY MODE buttonwh TIME buttonwj x buttonwk PHONES jackwl X buttone; PHONE LEVEL knob 6RCD-W10SECTION 3DISASSEMBLYNote : Disassemble the unit in the order as shown below.LOADING PANEL (1CD)LOADING PANEL (CDR)DISPLAY BOARDCD MECHANISM DECK (CDM66C-30B61B)CDR MECHANISM DECK (CDM65-RBD1)CDR BOARDHOLDER (MG) SUB ASSY, DUST COVERTRAYCASE (409538)FRONT PANEL SECTIONSETMOTOR ASSY (LOADING) (M201)OPTICAL PICK-UP (KRM-220CAA)TRAY (66)BD BOARDCAM (CH)MAIN BOARDOPTICAL BLOCKSECTION7RCD-W10Note : Follow the disassembly procedure in the numerical order given.3-1. Case (409538)3-2. Loading Panel (1CD)4case (409538)3two screws (case 3 TP2 3 x 8)1two screws (case 3 TP2 3 x 8)2two screws (case 3 TP2 3 x 8)front panel side1 Rotate the hole to the direction of arrow.CD mechanism deck (CDM66C-30B61B)423 two hooks4 loading panel (1CD)8RCD-W103-3. Loading Panel (CDR)3-4. Front Panel Section1 Slide the lever to the direction of arrow.24front panel sideCD mechanism deck (CDM65-RBD1)lever3 two hooks5 loading panel (CDR)7two claws8front panel section1connector (2 core) (CN900)2connector (3 core) (CN690)4connector (2 core) (CN920)5three screws (+BVTP 3 8)6four screws (+BVTP 3 8)3 flexible flat cable (21core) (CN671)9RCD-W103-5. DISPLAY Board3-6. CDR Mechanism Deck (CDM65-RBD1)6twelve screws (+BVTP 2.6 8)3four screws (+BVTP 2.6 8)5three screws (+BVTP 2.6 8)2two knobs (AMS)1knob (AMS)9CD-EJECT board7claw 8Remove the soldering.HARNESS PROCESSING q; flexible flat cable (21core) (CN700)qa DISPLAY board4 CD-SW boardPOWER-SW board3four screws (+BVTP 3 8)2 flexible flat cable (11core) (CN630)1 connector (4P) (CN631)4 CDR mechanism deck (CDM65-RBD1)10RCD-W103-8. CDR Board3-7. Tray1 Slide the lever (cam (CH) to the direction of arrow.4 tray2 Pull the tray while pressing the claw of the chassis in the direction of the arrow. 3 Pull the tray while pressing the claw of the chassis and the claw of the tray in the direction of the arrow. front panel sidelever (cam (CH)clawclawclawchassischassistray7 claw6 claw8connector (2 core) (CN104)3 flexible flat cable (32core) (CN101)4 flexible flat cable (11core) (CN102)5 flexible flat cable (11core) (CN103)9 CDR board2 bottom plate1four screws (+BVTP 2.6 8)11RCD-W103-9. Holder (MG) Sub Assy, Dust Cover3-10. Optical Pick-Up (KRM-220CAA)4three screws (+BVTP 2.6 8)3holder (MG) sub assy1two claws2two claws5dust cover5 flexible flat cable (32core) (from optical device)1two step screws2two screws (2X9) (G with), +p tappin)6optical pick-up (KRM-220CAA)3two insulators (main)4two insulators (main)12RCD-W103-11. Motor Assy (Loading)(M201)3-12. Cam (CH)1 Slide the cam (CH) to the direction of arrow.2 Remove the belt (loading) from the pulley of the motor assy.3 two claws4 motor assy (loading) (M201)116screw (+PTPWH 2.6 8)5holder (BU) sub assycam (CH)claw1243Aqaq; Slide the cam (CH) to the direction of arrow A while pressing the claw. qs cam (CH)7 gear (C)9 gear (B)8 claw13RCD-W103-13. CD Mechanism Deck (CDM66C-30B61B)3three screws (+BVTP 3 8)2 flexible flat cable (23core) (CN101)1connector (5P) (CN680)4 CD mechanism deck (CDM66C-30B61B)14RCD-W103-14. Tray (66)8tray (66)3hook7hook6hook4hook251 Turn the cam to the direction of arrow.15RCD-W103-15. BD Board3-16. Optical Block Section1 Remove soldering from the four points.3 BD board2 flexible flat cable (16core) 1 floating screw 4optical block section3shaft (BU holder) 2Rotate the cam (66) in the direction of 2 to move the shaft (BU holder) upper.cam (66) 16RCD-W103-17. MAIN Board4connector (2 core) (CN900)2connector (3 core) (CN690)1 flexible flat cable (21core) (CN671)3 flexible flat cable (11core) (CN630)5 flexible flat cable (4core) (CN631)7 flexible flat cable (23core) (CN660)6 connector (5core) (CN680)qatwo screws (+BVTT 3 6)q;three screws (+BVTP 3 8)8screw (+BVTP 3 8)qsfour screws (+BVTT 3 6)qdRemove the soldering.qgMAIN boardqfpower transformer9bracket (TR)17RCD-W10MEMO18RCD-W10SECTION 4TEST MODESetting the Test ModeProcedure:1. Press the POWER button to POWER on.2. Press the l AMS L (DECK A), SBM and l AMSL (DECK B) buttons in order without releasing the button.3. Turn the l AMS L (DECK B) knob to select the menu.4. Press the l AMS L (DECK B) knob to execute the testmode.Releasing the Test ModeProcedure 1:1. Turn the l AMS L (DECK B) knob to select the ShipMode.2. Press the l AMS L (DECK B) knob to execute the ShipMode.3. Press the POWER button to POWER off.Procedure 2:1. Press the l AMS L (DECK A), SBM and l AMSL (DECK B) buttons in order without releasing the button.2. Press the POWER button to POWER off.Contents of test modeNo.DisplayFunction1SYS VersionSystem version display2CDR VersionCDR version display3BU TestDeck A BU test mode4SERVICEDeck A Service mode5Ship ModeCD Shipment mode6FL ALL ONFluorescent indicator tube test7FL ALL OFFFluorescent indicator tube test8FL ITIMATSUFluorescent indicator tube test9LED CHECKL