JBL-SUB10-sub-sm 维修电路原理图.pdf

Balboa Series SUB10 Powered Subwoofer Service Manual JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 10/2006 RadioFans.CN 收音机爱 好者资料库 - CONTENTS - BASIC SPECIFICATIONS .1 PACKING.2 DETAILED SPECIFICATIONS .3 CONNECTIONS.5 OPERATION .7 TEST SET-UP AND PROCEDURE.8 EXPLODED VIEW/PARTS LIST9 AMPLIFIER BLOCK DIAGRAM10 DETAILED TROUBLESHOOTING.12 ELECTRICAL PARTS LIST .13 P.C.B. DRAWINGS.17 IC/TRANSISTOR PINOUTS.23 SCHEMATICS.24 BALBOA SUB10 SPECIFICATIONS Amplifier Power (RMS): 100 Watts Peak Dynamic Power *: 225 Watts Driver: 10 (254mm) Inputs: Line Level and LFE Crossover Frequency: Variable from 50Hz to 150Hz, 24 dB per octave Frequency Response: 30Hz 150Hz Dimensions (H x W x D): 19-3/4 x 14-1/16 x 14-3/4 (502mm x 357mm x 375mm) Weight: 35 lb/16kg JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice. * The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off. BALBOA series SUB10 RadioFans.CN 收音机爱 好者资料库BALBOA series SUB10 2Balboa Sub 10100W Powered Sub/ Plate Amp LINE VOLTAGEYes/NoHi/Lo LineUnitNotesUS 120VAC/60HzYes108-132VrmsNormal OperationEU 230VAC/50-60HzYes207-254VrmsNormal OperationNormal operation, MOMS requiredParameterSpecificationUnitQA Test LimitsConditionsNotesAmp SectionType (120V Model)AB ABN/A120V System is Class ABType (230V Model)GHN/A230V System is Class GLoad Impedance (speaker)4OhmsN/ANominalSystem average impedance8.2OhmsReferenceMeasured with AP using the ratio method, sweeping with an ext. amp 10 to 500 HzAverage on the operating BW from 10 to 500HzRated Output Power 120V100Watts95 Nominal input voltage Rated Output Power 230V105Watts100 Nominal input voltage Avgerage value - RMS Dynamic power103WattsReference Nominal input voltage 3/20 50 Hz Burst unit driven 6dB above the sensitivity to drive it into max power, measured value is the average of the 4 first consecutive peaksDynamic power HP134WattsReference Nominal input voltage Highest RMS of the first 4 consecutive peaksTHD Rated Power0.5%122K filterTHD 1 Watt0.1%0.322K filterDC Offset10mV-DC50 Speaker OutputDamping factor150DF100Measured at amplifier board speaker out terminals, Output power 90 Watts THD 10K ohmsN/ANominal over the audio BWReference onlyFiltersLow Pass (fixed or variable)Variable-2dB2nd order variable + 2nd order fix, Range 50-110 HzSubsonic filter (HPF)Fixed2dBFriend circuitFixed2dBLimiter (yes/no)YES-N/ATHD at Max. Output PowerN/A-N/AFeaturesLFE InputYESFunctional BW Limited to 500 Hz, Phase Switch (yes/no)YES-Functional Volume pot Taper (lin/log)LOG-Functional LP Variable Crossover controYESFunctional Range 50-110 HzATOYESFunctional fsInput ConfigurationLine In (L,R)L ,R-FunctionalRCA inputs: RED-WHT, L , R Summed to MonoLine level in LFELFEFunctionalSingle connectorSignal Sensing (ATO)Auto-Turn-On (yes/no)YES-FunctionalATO Input Frequency50HzFunctionalATO Level Line Level in (L,R1.5mVFunctional2mV50Hz into Line Input w/ 1 ch. drivenBALBOA series SUB10 3ParameterSpecificationUnitQA Test LimitsConditionsNotesATO Turn-on time T 15Power on Delay time3sec.FunctionalAC Power AppliedTransients/PopsATO Transient5mV-peak10 Speaker OutputsTurn-on Transient50mV-peak100 Speaker OutputsAC Line cycled from OFF to ONTurn-off Transient50mV-peak100 Speaker OutputsAC Line cycled from ON to OFFEfficiencyStand-by Input Power13Watts14 nom. line voltage Unit active, no signal applied (Green LED)Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation.Power Cons/Amps.rated power 120V Model192 / 1.89 Watts/Amps208 / 2.00 120V-60 Hz (Nom.line voltage)100 Watts 4 Ohms nominal line voltagePower Cons/Amps.rated power230V Model208 / 1.1Watts/Amps210 / 1.2 230V-50 Hz (Nom.line voltage)100 Watts 4 Ohms nominal line voltageProtectionShort Circuit Protection YES-FunctionalDirect short at outputThermal Protection 65 deg. C-Functional1/8 max unclipped Power Temperature rise should not exceed 35K riseDC Offset ProtectionYES-FunctionalDC present at Speaker Out leadsRelay or crowbar (for driver/fire protection)Line Fuse Rating120VAC2.5AmpsType-T or Slo BloExternal fuse with UL/SEMKO rated holder230VAC1.25AmpsType-T or Slo BloExternal fuse with UL/SEMKO rated holderBALBOA series SUB10 4CONTROLS AND CONNECTIONSRear PanelFUSET 2.5A L 250VTYPEAC120V60HZ200 WattsA Harman InternationalCompany0Subwoofer-Level Control 1Crossover Adjustment2Phase Switch3LFE Input4Line-Level Inputs 5Power Indicator LED6Power SwitchBALBOA series SUB10 5SUBWOOFER CONNECTIONSChoose the Subwoofer ConnectionThat Is Most Suitable for YourReceiver/ProcessorIf you have a DolbyDigital or DTSreceiver/processor with a low-frequency-effects (LFE) or subwoofer output: If your receiver/processor does not contain a Dolby Digital or DTSprocessor but has a subwoofer output:SUBWOOFER ORLFE OUTPUTLRNOTE: Some receivers have one subwoofer output. In that case, it is recommended that you use a Y connector (not included) to maximize performance.BALBOA series SUB10 6Power OnPlug your subwoofers AC cord into a wall outlet. Do not use theoutlets on the back of the receiver.Initially set the Subwoofer-Level Control to the “min” position.Turn on your sub by pressing the Power Switch on the rear panel.Turn on your entire audio system and start a CD or movie soundtrackat a moderate level.Auto On/StandbyWith the Power Switch in the ON position, the LED on the rearpanel will remain lit in red or green to indicate the On/Standby modeof the subwoofer.RED = STANDBY (no signal detected, amp off)GREEN = ON (signal detected, amp on)The subwoofer will automatically enter the Standby mode afterapproximately 10 minutes when no signal is detected from yoursystem. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch can be left on. You may turn off the Power Switch for extendedperiods of nonoperation, e.g., when you are away on vacation.Adjust LevelTurn your Subwoofer-Level Control up to the “5” position(halfway). If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cablesmaking proper contact? Is the AC plug connected to a “live”receptacle? Has the Power Switch been pressed to the “On”position? Once you have confirmed that the subwoofer is active,proceed by playing a CD, record or cassette. Use a selection that has ample bass information.Set the overall volume control of the preamplifier or stereo to acomfortable level. Adjust the Subwoofer-Level Control until you obtain a pleasing blend of bass. Bass response should notoverpower the room but rather be adjusted so there is a harmoniousblend across the entire musical range. Many users have a tendencyto set the subwoofer volume too loud, adhering to the belief that asubwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However,overall balance must be maintained or the music will not soundnatural. An experienced listener will set the volume of the subwooferso its impact on bass response is always there but never obtrusive.Phase ControlThe Phase Switch determines whether the subwoofer speakerspiston-like action moves in and out with the main speakers (0), oropposite the main speakers (180).Proper phase adjustment dependson several variables such as room size, subwoofer placement andlistener position. Adjust the phase switch to maximize bass output at the listening position. Crossover AdjustmentsThe Crossover Adjustment Control determines the highestfrequency at which the subwoofer reproduces sounds. If your mainspeakers can comfortably reproduce some low-frequency sounds,set this control to a lower frequency setting, between 50Hz and100Hz. This will concentrate the subwoofers efforts on the ultradeepbass sounds required by todays films and music. If you are usingsmaller bookshelf speakers that do not extend to the lower bassfrequencies, set the Crossover Adjustment Control to a highersetting, between 120Hz and 150Hz.N NO OT TE E: This control will have no effect if the LFE Input is used. Ifyou have a Dolby Digital or DTS processor/receiver, the Low-PassFrequency is set by the processor/receiver. Consult your ownersmanual to learn how to view or change this setting.OPERATIONBALBOA series SUB10 7 BALBOA SUB10 Test Set Up and Procedure SYSTEM AURAL SWEEP TEST Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables General Unit Function (UUT = Unit Under Test) Switches/knobs on the amplifier faceplate: Low Pass Frequency Adjust full CW (150Hz) Phase switch either position 1. From the signal generator, Connect both right and left line level inputs (RCA) not the LFE jack - to signal generator and UUT. Use Y-cable if necessary from mono source. 2. On the amplifier, turn the LEVEL control full Counterclockwise (Min). 3. Turn on generator, adjust to 100mV, 50 Hz. 4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max). 5. LED should now be Green; immediate bass response should be heard and felt from rear port tube opening. 6. Turn off generator, turn LEVEL control fully Counterclockwise (Min), disconnect RCA cable. Sweep Function 1. Follow steps 1-6 above, using a sweep generator as a signal source. 2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofer and test. Driver Function (Woofer) 1. Remove woofer from cabinet; detach + and - wire clips. 2. Check DC resistance of woofer; it should be 3.3 ohms 10%. 3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. BALBOA series SUB10 8EXPLODED VIEWBALBOA series SUB10 9BALBOA series SUB10 10BALBOA series SUB10 11 BALBOA SUB10 (UL) AMP Troubleshooting Flow Chart no yes yes yes no yes yes LED red LED light green yes yes no yes yes no no yes yes yes no no yes yes yes no yes yes AMP no signal out Dc voltage check Vcc Check+/-15VDC Led light green or red Check Fuse,Transformer, D110, etc Check RY101,D102,Q113,Q114 etc Check Q107,Q108,Q105, Q106,Q103,Q104,U101,etc Check ,+VCC& -VCC DC voltage Check U101,Q115,Q116,R138 etc Check Q117,118,119,D109 etc Check,Q206,Q207,U203 etc Check U202 pin14 signal Check U201 pin14 signal Test R121,R122 signal Check P102 signal The Amp assY OK, END CheckU201,U202,VR201 VR202. etc Check J123,J124 etc Check limiter board C304 Check U301,R343,R344 ,C340,Q301,Q302, etc Set R138 to R140S Voltage is 0.51VDC BALBOA series SUB10 12Balboa SUB10 (120v) Electrical Parts ListPart NumberDescriptionQtyReference DesignatorPOWER/MAIN PCBResistors110-14472j26-eResistor 4.7K 1/4W 5% CF 26mm (RoHS)2R147,R150,110-14681j26-eResistor 680 1/4W 5% CF 26mm (RoHS)2R148,R151,110-16101j26-eResistor 100 1/6W 5% CF 26mm (RoHS)1R120,110-16102j26-eResistor 1K 1/6W 5% CF 26mm (RoHS)1R124,110-16103j26-eResistor 10K 1/6W 5% CF 26mm (RoHS)1R134,110-16105j26-eResistor 1M 1/6W 5% CF 26mm (RoHS)1R143,110-16123j26-eResistor 12K 1/6W 5% CF 26mm (RoHS)2R135,R139,110-16152j26-eResistor 1.5K 1/6W 5% CF 26mm (RoHS)6R103,R123,R136,R137,141,R142,110-16153j26-eResistor 15K 1/6W 5% CF 26mm (RoHS)4R118,R145,R152,R154,110-16154j26-eResistor 150K 1/6W 5% CF 26mm (RoHS)1R131,110-16181j26-eResistor 180 1/6W 5% CF 26mm (RoHS)2R111,R114,110-16182j26-eResistor 1.8K 1/6W 5% CF 26mm (RoHS)1R153,110-16223j26-eResistor 22K 1/6W 5% CF 26mm (RoHS)3R128,R129,R133,110-16332j26-eResistor 3.3K 1/6W 5% CF 26mm (RoHS)3R106,R107,R144,110-16392j26-eResistor 3.9K 1/6W 5% CF 26mm (RoHS)2R105,R108,110-16393j26-eResistor 39K 1/6W 5% CF 26mm (RoHS)1R126,110-16470j26-eResistor 47 1/6W 5% CF 26mm (RoHS)4R112,R113,R115,R116,110-16471j26-eResistor 470 1/6W 5% CF 26mm (RoHS)1R140,110-16472j26-eResistor 4.7K 1/6W 5% CF 26mm (RoHS)3R110,R125,R130,110-16473j26-eResistor 47K 1/6W 5% CF 26mm (RoHS)1R101,110-16560j26-eResistor 56 1/6W 5% CF 26mm (RoHS)1R117,110-16563j26-eResistor 56K 1/6W 5% CF 26mm (RoHS)1R104,110-16682j26-eResistor 6.8K 1/6W 5% CF 26mm (RoHS)1R109,110-10821jk2-eResistor 820 1W 5% 10mm (RoHS)1R132,110-122r2j15-eResistor 2.2 1/2W 5% 15mm (RoHS)1R127,110-20331jk2-eResistor 330 2W 5% 5mm(RoHS)2R146,R149,113-50r10j10-ecement Resistor 0.1 5W 5% (RoHS)2R121,R122,114-03302m0-esemi-fixed Resistor 3K 0.3W 20%(RoHS)1R138,Capacitors130-2b102k503-edisc capacitor 1000P 50V 10% (RoHS)1C116,130-3f104z503-edisc capacitor 0.1U 50V +80/-20% (RoHS)4C108,C113,C115,C119,130-3f473m503-edisc capacitor 0.047U 50V 20% (RoHS)1C106,130-sl101k503-edisc capacitor 100P 50V SL 10% (RoHS)2C139,C140,132-104j503-emylar capacitor 0.1U 50V 5% (RoHS)1C107,132-223ja03-emylar capacitor 0.022uF 100V 5% (RoHS)4C124,C125,C126,C128,135-3105m50-eelectrolytic cap. 1U 50V 20% (RoHS)2C105,C112,135-3107m16-eelectrolytic cap. 100uF 16V 20% (RoHS)3C109,C117,C120,135-3226m50-eelectrolytic cap. 22U 50V 20% (RoHS)2C114,C118,135-3227m10-eelectrolytic cap. 220U 10V 20% (RoHS)2C129,C130,135-3227m16-eelectrolytic cap. 220U 16V 20% (RoHS)1C111,135-3476m25-eelectrolytic cap. 47U 25V 20% (RoHS)1C103,132-223ja03-emylar capacitor 0.022uF 100V 5% (RoHS)2C123,C127,135-3107m16-eelectrolytic cap. 100uF 16V 20% (RoHS)1C110,135-4688m50-eelectrolytic cap. 6800U/50V 20%D25X45mm (RoHS)2C121,C122,Semiconductors192-027c1815gr-etransistor 2SC1815GR TOSHIBA(RoHS) NPN5Q102,Q111,Q112,Q113,Q118,192-028a1015gr-etransistor 2SA1015GR TOSHIBA(RoHS) PNP2Q114,Q116,192-1572n5551-e*transistor FSC 2N5551 (RoHS) NPN2Q103,Q109,192-1582n5401-etransistor FSC 2N5401 AI-PNP 350V 500mA TO-92 (RoHS) PNP2Q104,Q110,197-031n4148-ediode 100mA 75V SIGNAL 1N4148 ROHM (RoHS)4D101,D103,D105,D108,199-15000335-ezener diode 3.3V 1/2W 52mm (RoHS)1D102,199-15000625-ezener diode HZ6C2 RENESAS (RoHS)2D106,D107,199-15001605-ezener diode HZ16-2 RENESAS (RoHS)1D109,BALBOA series SUB10 13Part NumberDescriptionQtyReference DesignatorPOWER/MAIN PCB190-06m4558d-eI.C. OPA 4558D (RoHS) DUAL OP-AMP 1U101,192-021tip35c-etransistor TIP35C (RoHS) NPN1Q107,192-022tip36c-etransistor TIP36C (RoHS) PNP1Q108,192-201d882y-e*transistor KSD882Y (RoHS) NPN1Q117,192-202b772y-e*transistor KSB772Y (RoHS) PNP1Q119,192-027c1815gr-etransistor 2SC1815GR TOSHIBA(RoHS) NPN2Q101,Q115,192-991d669a-etransistorHI-SINCERITY HSD669A(RoHS) NPN1Q106,192-992b649t-etransistor HSB649T (RoHS) PNP1Q105,197-00kbl405-ediode 4A 500V KBL405(RoHS) BRIDGE1D110,197-101n4002-ediode 1N4002TB (RoHS)1D104,Miscellaneous171-udhss124d-eRelay 5A 24V UDH-SS124D(R