HarmanKardon-SUBTS15-pwr-sm维修电路原理图.pdf

harman/kardon SUB-TS15SUB-TS15 (HKTS 15 SUBWOOFER) SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 2/2007 RadioFans.CN 收音机爱 好者资料库 CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . 2 PACKAGING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CONTROLS & CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . 5 SPEAKER CONNECTIONS. . . . . . . . . . . . 7 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . 10 TEST PROCEDURE. . . . . . . . . . . .11 UNIT EXPLODED VIEW. . . . . . . . . . . . . . 12 AMPLIFIER EXPLODED VIEW. . . . . . . . . . . . . . . . . 13 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DETAILED TROUBLESHOOTING.16 PCB DRAWINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 ELECTRICAL PARTS LIST . . . . . . . . . . 23 SEMICONDUCTOR PINOUTS . . . . . . . . . . . . . .27 SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . .28 SPECIFICATIONS Amplifier Power (RMS) 100 Watts Driver 10 (254mm) woofer, Bass Reflex Enclosure Inputs Stereo Line Level, dedicated Subwoofer (LFE) and Speaker Level with gold-plated binding posts Outputs Speaker Level with gold-plated binding posts Frequency Response 35Hz 120Hz (Filter switch ON) 35Hz 450Hz (Filter switch OFF) External Trigger Input Voltage: 3-30 Volts AC/DC Dimensions (H x W x D) 18-7/8 x 13-3/8 x 13-3/8 (479mm x 340mm x 340mm) Weight 35.11 lb/15.8kg Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated. SUB-TS15SUB-TS15 harman/kardonharman/kardon 1RadioFans.CN 收音机爱 好者资料库SUB-TS15 100W Powered Sub/ Plate AmpLINE VOLTAGEYes/NoHi/Lo LineNom.UnitNotesUS 120vac/60HzYes108-132120VrmsNormal OperationParameterNonimal SpecificationUnitQA Test LimitsConditionsNotesAmp SectionType (Class AB, D, other)ABn/an/aLoad Impedance (speaker)4Ohmsn/aNominalRated Output Power100Watts7550 - 250 Hz, 1 input driven, limiter offTHD Rated Power0.08%0.122k filterTHD 1 Watt0.15%0.522k filterDC Offset5mV-DC30 Speaker OutputsDamping factor100n/a30Measured at amplifier board Measured at the speaker at speaker output terminals on the amp board.Input SensitivityInput Frequency50Hzn/aNominal Freq.Line (L&R) Input 220mVrms154 - 308 To Rated PowerSingle input drivenSUB (LFE) Input125mVrms87 - 175To Rated PowerSUB (LFE) input driven onlySpeaker/Hi Level Input2.2Vrms1.5 - 3.0To Rated Power(20 dB below Line In), Single input drivenHi Level Max. Input Voltage32Vrms30Nominal Freq., Min. VolumeSignal to NoiseSNR-A-Weighted100dB85relative to rated powerA-Weighting filterSNR-unweighted90dB80relative to rated power22k filterSNR rel. 1W-unweighted65dB60relative to 1W Output22k filterResidual Noise Floor1.2mVrms3.0Volume max, using RMS reading DMM/VOM (or A/P)Residual Noise Floor0.8mVrms2.0Volume max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)Input ImpedanceLine Input (L, R,LFE)10Kohmsn/aNominalSpeaker/Hi Level Input4.7Kohmsn/aNominalFiltersL&R Fixed Low-Pass Filter170Hz150 - 200 -6dB ref. 100Hz2nd order fixedSUB (LFE) Low pass Filter270Hz240 - 300 -3dB ref. 100Hz2nd order fixedSubsonic filter (HPF) 3rd Order28Hz22 - 28 -3dB ref. 30Hz3rd order fixedLimiter THD at Max. Output Power2.0%5.0FeaturesAuto - On -Off Selection SwitchYESfunctional Refer to ATO sectionPhase Switch0-180degfunctional Filter On/Off SwitchYESfunctional Volume Pot Taper (Lin/Log)LOGfunctional A TaperSpeaker OutYESfunctional Binding post connector L&R2-Color LED power indicatorYESfunctional Blue: On, Amber: Stand-byPower SwitchYESfunctional Fuse HolderYESfunctional Input ConfigurationLine In (L,R)YESfunctional Dual RCA jackSUB (LFE)YESfunctional RCA jackSpeaker/Hi Level InYESfunctional Binding post connector L&RSignal Sensing (ATO)Auto-Turn-On (yes/no)YESfunctional Auto - on selection switch in Auto ATO Input test frequency50Hzn/aAuto - on selection switch in Auto ATO Level Line & SUB Input4.0mV2.0 - 6.0Auto - on selection switch in Auto ATO Level Speaker in40mV25 - 55Auto - on selection switch in Auto ATO Turn-on time5msfunctional Amp connected and AC on, then input signal appliedATO Turn-OFF Time15minutes10 - 20Time before muting, after signal is removedPower on Delay time3sec.functional AC Power AppliedTransients/PopsATO Transient5mV-peak10 Speaker OutputsTurn-on Transient50mV-peak100 Speaker OutputsAC Line cycled from OFF to ONSUB-TS15SUB-TS15 harman/kardonharman/kardon 2ParameterNonimal SpecificationUnitQA Test LimitsConditionsNotesTurn-off Transient50mV-peak100 Speaker OutputsAC Line cycled from ON to OFFEfficiencyStand-by Input Power10Watts12 nom. line voltageMaximum allowable input power under nominal input voltage and frequency, in stand-by mode (HOTor COLD operation).Power Consumption rated powe170Watts200 nom. line voltage100 Watts 4.0 ohms and nominal line voltageProtectionShort Circuit Protection YESfunctional Direct short at outputAmplifier should resume operation after short circuit condition is removed. Thermal Protection YESfunctionalAny user accessible metal parts should always remain at 65 degree C or less for domestic version or 55 degree C or less for EU version.DC Offset ProtectionYESfunctional DC present at Speaker Out leadsRelay or crowbar (for driver/fire protection), Primary Fuse RatingUSA-Domestic (120V)2.5Ampsn/aType-T or Slo BloUser-replacable fuse with UL/SEMCO rated holder.SUB-TS15SUB-TS15 harman/kardonharman/kardon 326313227282930252423222120191817161514131211109876543211234Color LabelWarranty CardWarranty CardOwners Manual0405-000-00333-E405-000-05033-E1.01.01.01.0406-000-05503-E55Packaging 1.0Packaging 1.06687Non-woven BagPE BagE14.04.0109Non-woven Bag2PE Bag41.01.011Cardboard4 1.0Wall Mounting Bracket 326-ABS-00108-0BAE 4.0326-FE-00109-E4.0336-EVA-05405-0BAE325-SPCC-05229-0BAE 1.0371-000-05168-E317-PS-00172-0BAE370-000-05034-E370-000-05035-E370-000-05036-E370-000-05037-E370-000-05038-E370-000-05039-E371-000-00360-E165-54505501-e 1.0401-000-00118-EInner Carton for Sat, Ctr26Top PackingBottom Packing431-000-05919-E431-000-05920-E1.01.027282930Non-woven BagPO Bag2 1.01.04313 2.0 Dessicant15ft RCA Signal CableSpeaker Cable 20ft. (Red)Speaker Cable 20ft. (Grn)Speaker Cable 20ft. (Wht)Speaker Cable 12M (Gry)Speaker Cable 12M (Blu)S32Outer Carton 402-000-05679-E 1.0.16 17 18 1912 13 14 1520 21 22 23 24Mounting PlateTerminal Cap1.01.01.01.01.01.01.01.0 Metal Bracket (Center)4.04.0Leather Coaster for SatsSignal Cable for TriggerSATCENSUB1.0ItemDescriptionPart NumberQtyPACKAGEScrew Bag forCEN Wall BracketScrew Bag forSAT Wall Bracket371-000-05168-E: 2pcs Flat head, 10mm( screw Length ) x 8mm(Screw head Dim.)?371-000-00360-E: 2pcs Round head, 1/4( screw Length ) x 10.5mm(Screw head Dim.)?4SUB-TS15SUB-TS15 harman/kardonharman/kardon SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS 5SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS Subwoofer-Level Control: Volume may be adjusted using the Subwoofer-Level Control.Turn the control clockwise to increase the SUB-TS15s volume, or counterclockwise to decrease it. High-Cut (Low-Pass) Filter Switch:Placing this switch in the ON position acti-vates circuitry that cuts out all audio inputsignals above 120Hz.This allows the SUB-TS15 to focus its power on reproducing thelow-frequency portion of the signal, avoidinginefficiency and distortion. Engage this filterwhen using the Speaker-Level Inputs ,or when using the Line-Level Full-RangeInputs , unless your receiver or processorprocesses its line-level output using a low-pass filter.The filter has no effect when theSUB Input is used. External Trigger Input: Use the sup-plied mini-plug cable to connect the triggeroutput of another compatible product to thisjack.Whenever a trigger signal between 3 and 30 volts (AC or DC) is detected, the SUB-TS15 amplifier will turn on, even whenthe Audio-Sense feature has been activatedby placing the Audio-Sense On/Off Switch in the AUTO position.The amplifier willremain on for about 1015 minutes withouta trigger signal. Audio-Sense On/Off Switch:Whenplaced in the AUTO position,and when theMaster Power Switch is turned on,theSUB-TS15 will automatically turn itself on or Subwoofer-Level Control High-Cut (Low-Pass) Filter Switch External Trigger Input Audio-Sense On/Off Switch Phase Switch Line-Level Subwoofer (SUB) Input Line-Level Full-Range Inputs Speaker-Level Outputs Speaker-Level Inputs Master Power Switch AC Power CordHKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 5SUB-TS15SUB-TS15 harman/kardonharman/kardon 56SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSSUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSplace itself in the Standby mode,depending onwhether it is receiving an audio signal.Whenthis switch is placed in the ON position,theSUB-TS15 will remain on,whether or not it isreceiving an audio signal.An LED located on top of the SUB-TS15indicates whether the SUB-TS15 is in theON or STANDBY state when used with theAudio-Sense On/Off Switch in theAUTO position.The LED is lit blue to indi-cate that the SUB-TS15 is receiving anaudio signal and is turned on, and the LED is lit amber to indicate that no signal is being received and the SUB-TS15 is inStandby mode.When the Audio-Sense On/Off Switch is in the ON position, the LED will be lit blue, whether or not an audio signal is present.When the Master Power Switch isturned off, the LED goes dark, no matterwhich position the Audio-Sense On/OffSwitch is in. Phase Switch: This switch determineswhether the SUB-TS15 subwoofers piston-like action moves in and out in phase withthe main speakers. If the speakers were toplay out of phase, the sound waves pro-duced by the subwoofer would be cancelledout, reducing bass response.This phenome-non depends in part on the relative place-ment of the speakers in the room. In mostcases, the Phase Switch should be leftin the NORMAL position. However, itdoes no harm to experiment with the PhaseSwitch , and you may leave it in theposition that maximizes bass response. Line-Level Subwoofer (SUB) Input:Connect the subwoofer output of a receiverwith digital surround sound decoding, suchas DolbyDigital or DTS,to this input.Thisinput bypasses the SUB-TS15s internalcrossover circuitry, and should only be usedwith a filtered signal. If your receiver does nothave digital decoding,you should use theLine-Level Full-Range Inputs instead. Line-Level Full-Range Inputs: Connectthe line-level subwoofer output or preamp out-put(s) of your receiver or amplifier to theseinputs.If your receiver does not have a sepa-rate subwoofer output,use a Y-adapter (notsupplied) to bridge the receivers preamp out-put to the main amp input for that channel,and connect the long end of the adapter to the corresponding line-level input on theSUB-TS15.If your receiver has only a singlesubwoofer output,you may connect it to either the left or right line-level input on theSUB-TS15,and no Y-adapter is needed. Speaker-Level Outputs: If you areusing the Speaker-Level Inputs on theSUB-TS15, you should connect these bind-ing-post terminals to your front left and rightspeakers, remembering to maintain polarityby connecting the (+) terminal on the SUB-TS15 subwoofer to the (+) terminal on thespeaker, and the () terminal on the SUB-TS15 subwoofer to the () terminal on thespeaker. If you are not using the Speaker-Level Inputs , then connect your frontleft and right speakers directly to your receiveror amplifier. See pages 9 through 12 for further information on speaker connections. Speaker-Level Inputs: If your receiveror amplifier does not have a line-level sub-woofer output, connect these binding-postterminals to the main left and right speakerterminals of your receiver or amplifier.Remember to maintain polarity by connectingthe (+) terminal on the receiver/amplifier to the(+) terminal on the SUB-TS15 subwoofer,andthe () terminal on the receiver/amplifier to the() terminal on the SUB-TS15 subwoofer. Master Power Switch: Place thisswitch in the “” position to power-on theSUB-TS15 subwoofer.The SUB-TS15 willthen be either in the Standby mode or com-pletely on, depending on the position of theAudio-Sense On/Off Switch . AC Power Cord: Make sure to plug this cord into an active, unswitched electrical out-let for proper operation of the SUB-TS15.The cord should not be plugged into theaccessory outlets found on some audiocomponents.HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 6SUB-TS15SUB-TS15 harman/kardonharman/kardon 6DolbyDigital or DTS(or OtherDigital Surround Mode) ConnectionUSE THIS INSTALLATION METHOD FORDOLBY DIGITAL, DTS OR OTHER DIGITALSURROUND PROCESSORS:Use the line-level input jack marked SUB for the Low-Frequency Effects channel.Connect this jack to the subwoofer output or LFE output on your receiver or amplifier.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure youve configured your surroundsound processor for “Subwoofer On. ” Thefront left, front right, center and surroundspeakers should all be set to “Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.SPEAKER CONNECTIONSLINE LEVEL INLRSUBSUB/LFE OutSUB-TS15 SubwooferReceiverFrontLeftSurroundLeftFrontRightSurroundRightCenterSurroundRightFrontRightSurroundLeftFrontLeftCenter + + + + +HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 10SUB-TS15SUB-TS15 harman/kardonharman/kardon 7SPEAKER CONNECTIONS 11Dolby Pro Logic(Non-Digital) Line LevelUSE THIS INSTALLATION METHOD FORDOLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR IS EQUIPPED WITH A SUB-WOOFER OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Use the supplied RCA-type interconnectcable to connect the line-level subwooferoutput on your receiveror amplifier to eitherthe left or right Line-Level Full-RangeInput on the SUB-TS15 subwoofer.Use both the left and right inputs on thesubwoofer if your receiver or processor hasboth left and right line-level outputs. In thatcase, you will need to supply a secondinterconnect cable.If your receiver is equipped with line-level out-puts but does not have a separate subwooferoutput,use a Y-adapter (not supplied) tobridge the receivers preamp output to themain amp input for that channel,and connectthe long end of the adapter to the corre-sponding line-level input on the SUB-TS15.IMPORTANT: Do not use the SUB Input on the subwoofer with Dolby Pro Logicprocessors.If your receiver/processor has a built-in low-pass-crossover filter for the subwoofer out-put, you may use the SUB Input tobypass the subwoofers internal crossover.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure that you have configured yoursurround sound processor for “SubwooferOn. ” The front left, front right, center andsurround speakers should all be set to“Small. ”When all connections have