HarmanKardon-SUBTS7-pwr-sm维修电路原理图.pdf

harman/kardon SUB-TS7(HKTS 7 SUBWOOFER) SUB-TS8(HKTS 8 SUBWOOFER) SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 10/2006 RadioFans.CN 收音机爱 好者资料库 CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 2 CONTROLS & CONNECTIONS. . . . . . . . . . . . . . 4 SPEAKER CONNECTIONS. . . . . . . . . . . . 6 OPERATION. . . . . . . . . . . . . . .9 BASIC TROUBLESHOOTING GUIDE . . . . . . . . .10 UNIT EXPLODED VIEW. . . . . . . . . . . . . . 11 AMPLIFIER EXPLODED VIEW. . . . . . . . . . . . . . . . 12 TEST SET-UP AND PROCEDURE. . . . . . . . .13 HKTS7 TECH TIP HK2004-04 .14 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 PCB DRAWINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . . 20 SEMICONDUCTOR PINOUTS . . . . . . . . . . . . . .24 HKTS7 SCHEMATIC DIAGRAM . . . . . . . .25 HKTS8 SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . 28 HKTS7 PACKAGING. . . . . . . . . . . . . . . . . . . . 31 HKTS8 PACKAGING. . . . . . . . . . . . . . . . . . . . 32 SPECIFICATIONS Amplifier Power (RMS) 100 Watts Driver 10 woofer, Bass Reflex Enclosure Inputs Stereo Line Level, dedicated Subwoofer (LFE) and Speaker Level with gold-plated binding posts Outputs Speaker Level with gold-plated binding posts Frequency Response 35Hz 120Hz (Filter switch ON) 35Hz 450Hz (Filter switch OFF) Dimensions (H x W x D) 18-7/8 x 13-3/8 x 13-3/8 479mm x 340mm x 340mm Weight 33 lb/15kg Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated. SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 1RadioFans.CN 收音机爱 好者资料库SUB-TS7 100W Powered Sub/ Plate AmpSUB-TS8 100W Powered Sub/ Plate AmpLINE VOLTAGEYes/NoHi/Lo LineNom.UnitNotesUS 120vac/60HzYes108-132120VrmsNormal OperationParameterNonimal SpecificationUnitQA Test LimitsConditionsNotesAmp SectionType (Class AB, D, other)ABn/an/aLoad Impedance (speaker)4Ohmsn/aNominalRated Output Power100Watts7550 - 250 Hz, 1 input driven, limiter offTHD Rated Power0.08%0.122k filterTHD 1 Watt0.15%0.522k filterDC Offset5mV-DC30 Speaker OutputsDamping factor100n/a30Measured at amplifier board Measured at the speaker at speaker output terminals on the amp board.Input SensitivityInput Frequency50Hzn/aNominal Freq.Line (L&R) Input 220mVrms154 - 308 To Rated PowerSingle input drivenSUB (LFE) Input125mVrms87 - 175To Rated PowerSUB (LFE) input driven onlySpeaker/Hi Level Input2.2Vrms1.5 - 3.0To Rated Power(20 dB below Line In), Single input drivenHi Level Max. Input Voltage32Vrms30Nominal Freq., Min. VolumeSignal to NoiseSNR-A-Weighted100dB85relative to rated powerA-Weighting filterSNR-unweighted90dB80relative to rated power22k filterSNR rel. 1W-unweighted65dB60relative to 1W Output22k filterResidual Noise Floor1.2mVrms3.0Volume max, using RMS reading DMM/VOM (or A/P)Residual Noise Floor0.8mVrms2.0Volume max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)Input ImpedanceLine Input (L, R,LFE)10Kohmsn/aNominalSpeaker/Hi Level Input4.7Kohmsn/aNominalFiltersL&R Fixed Low-Pass Filter170Hz150 - 200 -6dB ref. 100Hz2nd order fixedSUB (LFE) Low pass Filter270Hz240 - 300 -3dB ref. 100Hz2nd order fixedSubsonic filter (HPF) 3rd Order28Hz22 - 28 -3dB ref. 30Hz3rd order fixedLimiter THD at Max. Output Power2.0%5.0FeaturesAuto - On -Off Selection SwitchYESfunctional Refer to ATO sectionPhase Switch0-180degfunctional Filter On/Off SwitchYESfunctional Volume Pot Taper (Lin/Log)LOGfunctional A TaperSpeaker OutYESfunctional Binding post connector L&R2-Color LED power indicatorYESfunctional Blue: On, Amber: Stand-byPower SwitchYESfunctional Fuse HolderYESfunctional Input ConfigurationLine In (L,R)YESfunctional Dual RCA jackSUB (LFE)YESfunctional RCA jackSpeaker/Hi Level InYESfunctional Binding post connector L&RSignal Sensing (ATO)Auto-Turn-On (yes/no)YESfunctional Auto - on selection switch in Auto ATO Input test frequency50Hzn/aAuto - on selection switch in Auto ATO Level Line & SUB Input4.0mV2.0 - 6.0Auto - on selection switch in Auto ATO Level Speaker in40mV25 - 55Auto - on selection switch in Auto ATO Turn-on time5msfunctional Amp connected and AC on, then input signal appliedATO Turn-OFF Time15minutes10 - 20Time before muting, after signal is removedPower on Delay time3sec.functional AC Power AppliedTransients/PopsATO Transient5mV-peak10 Speaker OutputsTurn-on Transient50mV-peak100 Speaker OutputsAC Line cycled from OFF to ONSUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 2ParameterNonimal SpecificationUnitQA Test LimitsConditionsNotesTurn-off Transient50mV-peak100 Speaker OutputsAC Line cycled from ON to OFFEfficiencyStand-by Input Power10Watts12 nom. line voltageMaximum allowable input power under nominal input voltage and frequency, in stand-by mode (HOTor COLD operation).Power Consumption rated powe170Watts200 nom. line voltage100 Watts 4.0 ohms and nominal line voltageProtectionShort Circuit Protection YESfunctional Direct short at outputAmplifier should resume operation after short circuit condition is removed. Thermal Protection YESfunctionalAny user accessible metal parts should always remain at 65 degree C or less for domestic version or 55 degree C or less for EU version.DC Offset ProtectionYESfunctional DC present at Speaker Out leadsRelay or crowbar (for driver/fire protection), Primary Fuse RatingUSA-Domestic (120V)2.5Ampsn/aType-T or Slo BloUser-replacable fuse with UL/SEMCO rated holder.SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 3SUB-TS8 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS 5 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSOFFONAUTOONFILTERNORMALREVERSEPHASEINOUTAC 120V60HzPOWERWARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,REPLACE ONLY WITH SAME TYPE T 2.5A L/250 VOLT FUSEAVERTISSEMENT: UTILISEZ UN FUSIBLE DE RECHANGE DE MEMETYPE T 2.5A L/250VRLLINELEVELINMAXMINIMPORTANT: CONNECT STRIPED WIRETO RED ( ) SPEAKER TERMINAL.LRSUBWOOFERLEVELRISK OF ELECTRIC SHO CK DO NO T OPENCAUTI O NRISK OF ELECTRIC SHO CK DO NO T OPENCAUTI O NRISK OF ELECTRIC SHO CK DO NO T OPENHIGH LEVELSUB Subwoofer-Level Control: Volume may be adjusted using the Subwoofer-Level Control.Turn the control clockwise to increase the Subwfr volume, or counterclockwise to decrease it. High-Cut (Low-Pass) Filter Switch:Placing switch in the ON position activatescircuitry that cuts out all audio input signalsabove 120Hz.This allows the Subwfr to focus its power on reproducing the low-frequency portion of the signal, avoiding inefficiency and distortion. Engage this filterwhen using the Speaker-Level Inputs ,or when using the Line-Level Full-RangeInputs , unless your receiver or processorprocesses its line-level output using a low-pass filter.The filter has no effect when theSUB Input is used. Music-Sense On/Off Switch:Whenplaced in the AUTO position,and when theMaster Power Switch is turned on,theSubwfr will automatically turn itself on orplace itself in the Standby mode,depending onwhether it is receiving an audio signal.Whenthis switch is placed in the ON position,theSubwfr will remain on,whether or not it isreceiving an audio signal.An LED located on top of the Subwfr indi-cates whether the Subwfr is in the ON orSTANDBY state when used with the Music-Sense On/Off Switch in the AUTOposition.The LED is lit blue to indicate thatthe Subwfr is receiving an audio signal Subwoofer-Level Control High-Cut (Low-Pass) Filter Switch Music-Sense On/Off Switch Phase Switch Line-Level Subwoofer (SUB) Input Line-Level Full-Range Inputs Speaker-Level Outputs Speaker-Level Inputs Master Power Switch AC Power CordSUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 46SUB-TS8 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSand is turned on, and the LED is lit amber toindicate that no signal is being received andthe Subwfr is in Standby mode.When the Music-Sense On/Off Switch is in the ON position, the LED will be lit blue, whether or not an audio signal is present.When the Master Power Switch isturned off, the LED goes dark, no matterwhich position the Music-Sense On/OffSwitch is in. Phase Switch: This switch determineswhether the subwoofers piston-like action moves in and out in phase withthe main speakers. If the speakers were toplay out of phase, the sound waves pro-duced by the subwoofer would be cancelledout, reducing bass response.This phenome-non depends in part on the relative place-ment of the speakers in the room. In mostcases, the Phase Switch should be leftin the NORMAL position. However, itdoes no harm to experiment with the PhaseSwitch , and you may leave it in theposition that maximizes bass response. Line-Level Subwoofer (SUB) Input:Connect the subwoofer output of a receiverwith digital surround sound decoding, suchas Dolby* Digital or DTS, to this input.Thisinput bypasses the Subwfrs internalcrossover circuitry, and should only be usedwith a filtered signal. If your receiver does nothave digital decoding,you should use theLine-Level Full-Range Inputs instead. Line-Level Full-Range Inputs: Connectthe line-level subwoofer output or preamp out-put(s) of your receiver or amplifier to theseinputs.If your receiver does not have a sepa-rate subwoofer output,use a Y-adapter (notsupplied) to bridge the receivers preamp out-put to the main amp input for that channel,and connect the long end of the adapter to the corresponding line-level input on theSubwfr.If your receiver has only a singlesubwoofer output,you may connect it to either the left or right line-level input on theSubwfr,and no Y-adapter is needed. Speaker-Level Outputs: If you areusing the Speaker-Level Inputs on theSubwfr, you should connect these binding-post terminals to the front left and rightspeakers, remembering to maintain polarityby connecting the (+) terminal on the subwoofer to the (+) terminal on the speaker, and the () terminal on the subwoofer to the () terminalon the speaker. If you are not using theSpeaker-Level Inputs , then connectyour front left and right speakers directly to your receiveror amplifier. See pages 8 for further information on speaker connections. Speaker-Level Inputs: Connect thesebinding-post terminals to the main left andright speaker terminals of your receiver oramplifier, if your receiver or amplifier doesnot have a line-level subwoofer output.Remember to maintain polarity by connectingthe (+) terminal on the receiver/amplifier to the(+) terminal on the subwoofer,andthe () terminal on the receiver/amplifier to the() terminal on the subwoofer. Master Power Switch: Place thisswitch in the “” position to power-on the subwoofer.The Subwfr will thenbe either in the Standby mode or completelyon, depending on the position of the Music-Sense On/Off Switch . AC Power Cord: Make sure to plug this cord into an active, unswitched electrical out-let for proper operation of the Subwfr.The cord should not be plugged into theaccessory outlets found on some audiocomponents.SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 510SPEAKER CONNECTIONSDolby* Digital or DTS(or OtherDigital Surround Mode) ConnectionUSE THIS INSTALLATION METHOD FORDOLBY DIGITAL, DTS OR OTHER DIGITALSURROUND PROCESSORS:Use the line-level input jack marked SUB for the Low-Frequency Effects channel.Connect this jack to the subwoofer output or LFE output on your receiver or amplifier.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure youve configured your surroundsound processor for “Subwoofer On. ” Thefront left, front right, center and surroundspeakers should all be set to “Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.SPEAKER CONNECTIONSLINE LEVEL INLRSUBSUB/LFE Out SubwooferReceiverFrontLeftSurroundLeftFrontRightSurroundRightCenterSurround BackSurroundRightFrontRightSurroundLeftFrontLeftCenterSurroundBackSUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 6SPEAKER CONNECTIONS 11Dolby Pro Logic* (Non-Digital) Line LevelUSE THIS INSTALLATION METHOD FORDOLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR IS EQUIPPED WITH A SUB-WOOFER OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Use the supplied RCA-type interconnectcable to connect the line-level subwooferoutput on your receiveror amplifier to eitherthe left or right Line-Level Full-RangeInput on the subwoofer. Useboth the left and right inputs on the sub-woofer if your receiver or processor hasboth left and right line-level outputs. In thatcase, you will need to supply a secondinterconnect cable.If your receiver is equipped with line-level out-puts but does not have a separate subwooferoutput,use a Y-adapter (not supplied) tobridge the receivers preamp output to themain amp input for that channel,and connectthe long end of the adapter to the corre-sponding line-level input on the Subwfr.IMPORTANT: Do not use the SUB Input on the subwoofer with Dolby Pro Logicprocessors.If your receiver/processor has a built-in low-pass-crossover filter for the subwoofer out-put, you may use the SUB Input tobypass the subwoofers internal crossover.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure that you have configured yoursurround sound processor for “SubwooferOn. ” The front left, front right, center andsurround speakers should all be set to“Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.SPEAKER CONNECTIONSSUB/LFE OutFrontLeftSurroundLeftFrontRightSurroundRight8SubwooferCenterSurround BackLine-LevelRLSurroundRightFrontRightSurroundLeftFrontLeftCenterReceiverSurroundBackSUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 712SPEAKER CONNECTIONSSPEAKER CONNECTIONSFront LeftSurround LeftCenterFront RightSurround RightSUB-TS8SubwooferSurroundRightFrontRightSurroundLeftFrontLeftCenterLRHIGH LEVELReceiverSurround BackSurroundBackDolby Pro Logic (Non-Digital) Speaker LevelUSE THIS INSTALLATION METHOD FORDOLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR DOES NOT HAVE A SUB-WOOFER OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Connect your receiver or amplifiers frontleft and right speaker terminals to the leftand right Speaker-Level Input termi-nals on the Subwfr subwoofer that aremarked “High Level In.” Connect the left andright Speaker-Level Output terminalson the Subwfr subwoofer that are marked“High Level Out” to the corresponding ter-minals on the back of your front left and rightspeakers.Connect your receiver or amplifiers centerand surround speaker terminals to the corresponding terminals on the back ofyour center and surround speakers.When all connections have been made,plug the AC power cord on the subwooferinto an AC outlet.SUB-TS7/TS8 harman/kardon