HarmanKardon-AVR3600-avr-sm维修电路原理图.pdf

harman/kardon AVR 3600 AVR 3600 7 X 80W 7.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.11 CONNECTIONS/INSTALLATION.14 INITIAL SETUP.17 OPERATION.21 TROUBLESHOOTING GUIDE.27 REMOTE & PROCESSOR RESETS.27 DISASSEMBLY.28 UNIT EXPLODED VIEW.29 EXPLODED VIEW PARTS LIST30 AMP BIAS ADJUSTMENT.31 BLOCK DIAGRAM.32 PCB DRAWINGS33 ELECTRICAL PARTS LIST.40 SEMICONDUCTOR PINOUTS.86 SCHEMATICS.216 WIRING DIAGRAM.229 harman/kardon, Inc. 8500 Balboa Blvd. Released 2009 Northridge, CA. 91329 Rev0 2/2010 Discontinued XXXX RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :AVR3600 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库2SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60Hz outlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundAVR3600 harman/kardonharman/kardon 365AVR 3600 TECHNICAL SPECIFICATIONSENGLISHAudi o Secti onStereo Mode, Continuous Average Power (FTC)80 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohmsSeven-Channel Surround Modes Power per Individual ChannelFront L & R channels:80 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:80 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround (L & R Side, L & R Back) channels:80 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)100dBSurround System Adjacent Channel SeparationPro LogicII40dBDolbyDigital (AC-3)55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz 130kHzHigh Instantaneous Current Capability (HCC)35 AmpsTransient Intermodulation Distortion (TIM)UnmeasurableSlew Rate40V/secFM Tuner Secti onFrequency Range87.5108.0MHzUsable SensitivityIHF 1.3V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection90dBAM Tuner Secti onFrequency Range5201710kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVi deo Secti onTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response (Composite and S-Video)10Hz8MHz (3dB)Video Frequency Response (Component Video) 10Hz100MHz (3dB)HDMIVersion 1.3a with 10-bit Deep ColorGeneralPower RequirementAC 120V/60HzPower Consumption890W maximum(7 channels driven)Stand-by consumption1WDimensions (Product)(Shipping)Width17-5/16 inches (440mm) 21-7/8 inches (555mm) Height6-1/2 inches (165mm)10-1/2 inches (266mm) Depth15 inches (382mm)18-5/16 inches (465mm)(Product)(Shipping)Weight 27.3 lb (12.4kg) 32.1 lb (14.6kg)Depth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.Features, specifications and appearance are subject to change without notice.Harman Kardon and Logic 7 are trademarks of Harman International Industries, Incorporated, registered in theUnited States and/or other countries. EzSet/EQ, Designed to Entertain and The Bridge III logo are trademarks ofHarman International Industries, Incorporated.iPod, iTunes and Apple are trademarks of Apple Inc., registered in the U.S. and other countries. iPhone is a trade-mark of Apple Inc. iPod and iPhone not included. “Made for iPod” means that an electronic accessory has beendesigned to connect specifically to iPod and has been certified by the developer to meet Apple performance stan-dards. “Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhoneand has been certified by the developer to meet Apple performance standards. Apple is not responsible for theoperation of this device or its compliance with safety and regulatory standards.A-BUS is a registered trademark of Leisure Tech Electronics Pty Ltd.Blu-ray Disc is a trademark of the Blu-ray Disc Association.CEA is a registered trademark of the Consumer Electronics Association.Cirrus Logic is a registered trademark of Cirrus Logic, Inc.Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the doubleD symbol are registeredtrademarks of Dolby Laboratories. MLP Lossless is a trademark of Dolby Laboratories.Manufactured under license under U.S. Patent #s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616;6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 and other U.S. and worldwide patents issued and pending.DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks ofDTS, Inc. (c) 1996-2008 DTS, Inc. All Rights Reserved.Faroudja DCDi Cinema is a trademark of Genesis Microchip Inc.HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMILicensing LLC.SACD is a trademark of Sony Corporation.TiVo is a registered trademark of TiVo Inc.SIRIUS and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All other marksand logos are the property of their respective owners. All rights reserved. SIRIUS subscription sold separately. Taxesand a one-time activation fee may apply. SIRIUS tuner required (sold separately) to receive the SIRIUS service. Allprogramming and fees subject to change. It is prohibited to copy, decompile, disassemble, reverse engineer, hack,manipulate or otherwise make available any technology or software incorporated in receivers compatible with theSIRIUS Satellite Radio System. Service not available in Alaska or Hawaii.This product incorporates copyright protection technology that is protected by method claims of certain U.S. patentsand other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copy-right protection technology must be authorized by Macrovision Corporation and is intended for home and other lim-ited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or diassemblyis prohibited.Please register your AVR 3600 at .Youll need the products serial number. At the same time, you canchoose to be notified about new products and/or special promotions.0139CSK - HK AVR 3600 OM Inlay ENG Marked_Rev 07 PRESS.qxp:HKP1477AVR245om.v2.qxd 22/07/09 15:24 Side 654AVR 3600AVR 3600AVR 360033visit AVR3600 harman/kardonharman/kardon 57FRONT-PANEL CONTROLSResolutionNavigationVideoModesSource ListBack/ExitOKNavigationHeadphoneJack/EzSet/EQMicrophoneInputDigitalAudio Inputs(Optical andCoaxial Front)USBPortVideo Front InputAnalog Audio Front InputsSurroundModesAudio EffectsSetupStandby/OnSwitchInfoSettingsVolumeMessage DisplayPowerIndicator/RemoteIR SensorNOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the ProductSupport section at .0139CSK - HK AVR 3600 OM Inlay ENG Marked Rev 04.qxp:HKP1477AVR245om.v2.qxd 03/06/09 14:50 Side 7FRONT PANEL CONTROLSAVR3600 harman/kardonharman/kardon 68FRONT-PANEL CONTROLSPower Indicator: This LED has three possible modes: Main Power Off: When the AVR is unplugged or the rear-panel Main Power Switch is off, this LED is off. Standby: Amber indicates that the AVR is ready to be turned on. On: When the AVR is turned on, this LED turns white. NOTE: If the PROTECT message ever appears, turn off theAVR and unplug it. Check all speaker wires for a possible short.If none is found, bring the unit to an authorized Harman Kardonservice center for inspection and repair before using it again.Standby/On Switch: This electrical switch turns thereceiver on, or places it in Standby mode for quick turn-on.Setup Button: Press this button to access the AVRs mainmenu.Info Settings Button: Press this button to directly accessthe AVRs Source Info submenu, which contains the settings for the current source.Resolution: Press this button to access the AVRs video outputresolution setting: 480i, 480p, 720p, 1080i, 1080p or 1080p/24 (if available on source and display).IMPORTANT NOTE: If the AVRs video output resolutionis set higher than the capabilities of the actual connection,you will not see a picture. If the best available video connectionfrom the AVR to the TV is composite video, press this buttonand change the resolution to 480i.Audio Effects:Press this button to directly access the AudioEffects submenu, which allows adjustment of the tone and otheraudio controls. See the Initial Setup section for more information.Video Modes: Press this button for direct access to the VideoModes submenu, which contains settings that may be used toimprove the picture, if necessary, after you have adjusted the picture settings using the video display or TV.Surround Modes:Press this button to select a surroundsound (e.g., multichannel) mode. The Surround Modes menu willappear on screen, and the menu line will appear in the front-paneldisplay. See the Advanced Functions section for more informationon surround modes. Source List: Press this button to select a source device,which is a component where a playback signal originates, e.g., DVD.Back/Exit: Press this button to return to the previous menu, or to exit the menu system.5/17/3Navigation: These buttons are used to navigate theAVRs menus.OK: Press this button to select the currently highlighted item.Headphone Jack/EzSet/EQ MicrophoneInput: Plug a 1/4 headphone plug into this jack for private listening.This jack is also used to connect the supplied microphone for theEzSet/EQ procedure described in the Initial Setup section. USB Port: This port may be used in case a software upgradefor the receiver is offered in the future. Do not connect a storagedevice, peripheral product or a PC here, unless instructed to do so as part of an upgrade procedure.Digital Audio and Analog Audio/Video FrontInputs: Connect a source component that will only be used temporarily, such as a digital camera or game console, to thesejacks. Use only one type of audio and one type of video connection.NOTE: The AVRs menus refer to these jacks as the OpticalFront, Coaxial Front, Composite Front, and Analog Front inputs. Volume Knob:Turn this knob to raise or lower the volume.Message Display:Various messages appear in this two-linedisplay in response to commands and changes in the incoming signal.In normal operation, the current source name appears on the upperline, while the surround mode is displayed on the lower line. Whenthe on-screen display menu system (OSD) is in use, the currentmenu settings appear.Remote IR Sensor:This sensor receives infrared (IR) commands from the remote control. It is important to ensure that itis not blocked. If covering the sensor is unavoidable, use an optionalHarman Kardon HE 1000, or other infrared receiver, connecting it tothe Remote IR Input on the AVR 3600s rear panel. 0139CSK - HK AVR 3600 OM Inlay ENG Marked v2.qxp:HKP1477AVR245om.v2.qxd 28/05/09 11:18 Side 8FRONT PANEL CONTROLSAVR3600 harman/kardonharman/kardon 79REAR-PANEL CONNECTIONSAnalog 1-5 Inputs6/8 ChannelInputsVideo1, 2 & 3InputsRemoteIR InputZone 2 IR InputSIRIUSTunerThe Bridge IIIRemoteIR OutputHDMI 1-4InputsHDMIMonitorOutputVideoMonitorOutputCenterSpeakerOutputsSwitched ACAccessoryOutletMainPowerSwitchComponent1 & 2InputsSurroundBack/Zone 2SpeakerOutputsFrontSpeakerOutputsZone 2 Audio OutputsAM AntennaFM AntennaA-BUS Power InputCarrier IROutputAnalog 2 & 4Audo OutputsSurroundSpeakerOutputsA-BUS PortComponent VideoMonitor OutputAC Power InputVideo 2OutputA-BUSIR O