HarmanKardon-DPR2005-avr-sm维修电路原理图.pdf

harman/kardon DPR1005 DPR2005 DPR1005 DPR2005 DIGITAL PATH AUDIO/VIDEO RECEIVER SERVICE MANUAL CONTENTS NOTICES PLEASE READ FIRST.2 ELECTROSTATICALLY SENSITIVE DEVICES.3 LEAKAGE TESTING.4 DPR1005 SPECIFICATIONS. .5 DPR2005 SPECIFICATIONS. .6 FRONT PANEL CONTROLS.7 REAR PANEL CONNECTIONS.10 MAIN REMOTE CONTROL FUNCTIONS.13 INSTALLATION/CONNECTIONS17 OPERATION.20 TROUBLESHOOTING GUIDE.26 PROCESSOR RESET.26 UNIT EXPLODED VIEWS.27 EXPLODED VIEW PARTS LIST.29 BLOCK DIAGRAM.31 BULLETIN HK2005-03.32 TECH TIP HKTT2003-01.33 CIRCUIT DESCRIPTION.34 D2 GR70/GR120 POWER MODULE.35 DPR1005 MECHANICAL PARTS LIST.51 DPR1005 ELECTRICAL PARTS LIST.52 DPR2005 MECHANICAL PARTS LIST.63 DPR2005 ELECTRICAL PARTS LIST.64 SMPS (Power Supply) Electrical Parts List.75 SEMICONDUCTOR DATA.79 PCB DRAWINGS.103 SCHEMATICS.113 WIRING DIAGRAM.126 PACKAGING.127 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 7/2005 www.freeservicemanuals.infoIts Freewww.freeservicemanuals.infoRadioFans.CN 收音机爱 好者资料库IMPORTANT NOTICES IMPORTANT NOTICES DPR1005 and 2005 that are under the two-year warranty period are considered factory service only in the United States. Please have Customers contact harman/kardon directly at (516) 255-4545 to obtain warranty service. This service manual is being made available for units that are no longer under warranty, and products that are serviced outside the U.S. During testing, do not inject an audio signal frequency into the unit higher than 20kHz with no load. Peaking in the output filter can cause the output voltages to exceed the filter capacitor voltage rating in this design. Normal audio program material will not have enough energy to cause problems. Avoid test tones above 20kHz. The following pages 8 - 27, reprinted from the DPR2005 owners manual, are accurate for every feature and operation of both the DPR1005 and DPR2005 with the following exception: The only feature difference between the two models is located in the front accessory jacks. On the 2005 the Front-panel digital coaxial/optical jacks may be used as either Inputs or Outputs. Those same jacks on the 1005 are for Inputs only; therefore there is also a missing indicator light for this function. For an accurate explanation of these jacks, refer to the DPR1005 owners manual. DPR1005/2005 DPR1005/2005 harman/kardon www.freeservicemanuals.infoIts Freewww.freeservicemanuals.infoRadioFans.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :DPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon www.freeservicemanuals.infoIts Freewww.freeservicemanuals.info 1. Inspect all lead dress to make certain thatleads are not pinched or that hardware is notlodged between the chassis and other metalpartsintheunit.2. Be sure that any protective devices such asnonmetallic control knobs, insulating fish-papers,cabinetbacks,adjustmentandcompartment covers or shields, isolationresistor-capacitynetworks,mechanicalinsulators, etc. Which were removed for theservicingareproperlyre-installed.Before returning the unit to the user, perform the following safety checks :3. Be sure that no shock hazard exists ; check for leakagecurrentusingSimpsonModel229LeakageTester,standardequipment item No. 21641, RCA Model WT540A or usealternate method asfollows : Plug the power cord directlyInto a 120 volt AC receptacle (do not use an IsolationTransformer for this test). Using two clip leads, connect a1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,suchas a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltage drop across theresistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal,cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thistestshouldbeperformedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningtheunittotheowner.DPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon www.freeservicemanuals.infoIts Freewww.freeservicemanuals.info250 Crossways Park Drive,Woodbury, New York 11797 2004 Harman International Industries, Incorporated Part No. ZKD0301HA00-9DPR 1005 TECHNICAL SPECIFICATIONSAudio SectionStereo Mode Continuous Average Power (FTC)70 Watts per channel, 20Hz20kHz, 0.15% THD, both channels driven into 8 ohmsSeven-Channel Surround Modes Power per Individual ChannelFront L&R channels:70 Watts per channel 0.15% THD, 20Hz20kHz into 8 ohmsCenter channel:70 Watts 0.15% THD, 20Hz20kHz into 8 ohmsSurround (L & R Side, L & R back) channels:70 Watts per channel 0.15% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)97dBSurround System Adjacent Channel SeparationPro Logic I/II/IIx 40dBDolby Digital 55dBDTS55dBTransient Intermodulation Distortion (TIM)UnmeasurableFM Tuner SectionFrequency Range87.5108.0MHzUsable SensitivityIHF 1.3V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequency Range5201720kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response (Composite and S-Video)10Hz8MHz (3dB)Video Frequency Response (Component Video) 10Hz50MHz (3dB)GeneralPower RequirementAC 120V/60HzPower ConsumptionStandby:8.9WIdle:52WMax:760W(7 channels driven)DimensionsProductShippingWidth17.3 inches (440mm)20.1 inches (510mm)Height4.5 inches (114mm)10 inches (254mm)Depth18.8 inches (476mm)22.2 inches (565mm)Weight23.1 lb (10.5kg)47 lb (21.4kg)Depth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon, Power for the Digital Revolution and Logic 7 are registered trademarks of Harman International Industries, Incorporated.is a trademark of Harman International Industries, Incorporated (patent no. 5,386,478).*Trademarks of Dolby Laboratories.DTS, DTS Surround, DTS-ES and DTS Neo:6 are registered trademarks of Digital Theater Systems, Inc.VMAx is a registered trademark of Harman International Industries, Incorporated, and is an implementation of Cooper Bauck Transaural Stereo under patent license.HDCD system manufactured under license from Pacific Microsonics, Inc.This product is covered by one or more of the following: in the USA: 5,479,168; 5,638,074; 5,640,161; 5,808,574;5,838,274; 5,854,600; 5,864,311; 5,872,531; and in Australia: 669114. Other patents pending.A-BUS and A-BUS Ready are registered trademarks of Leisure Tech Electronics Pty Ltd Australia.TiVo is a registered trademark of TiVo, Inc.Replay TV is a registered trademark of Digital Networks North America, Inc.TMwww.freeservicemanuals.infoIts Freewww.freeservicemanuals.info250 Crossways Park Drive,Woodbury, New York 11797 2004 Harman International Industries, Incorporated Part No. ZKD0401HA00-3DPR 2005 TECHNICAL SPECIFICATIONSAudio SectionStereo Mode Continuous Average Power (FTC)120 Watts per channel, 20Hz20kHz, 0.15% THD, both channels driven into 8 ohmsSeven-Channel Surround Modes Power per Individual ChannelFront L&R channels:120 Watts per channel 0.15% THD, 20Hz20kHz into 8 ohmsCenter channel:120 Watts 0.15% THD, 20Hz20kHz into 8 ohmsSurround (L & R Side, L & R back) channels:120 Watts per channel 96 dB Dynamic Range 90% Efficient Internal heat sinkConfigurable Audio Processing Treble, Bass, Volume Control, and EQ per channel Dynamic range compression and output limiting Standard 2-wire serial interface controlled via micro controller or remote PC GUIPure Digital Path 8-channel digital audio inputs (32 -192 kHz, 16-24 bit) are mapped to 7 speaker output channelsGraceful Protection and Recovery Short-circuit, thermal, over-current faultsPowered Second Zone Dynamic configuration for 7 channels or 5 channels plus stereo second zone. 2-channel analog or independent rate digital input selection for second zoneThe D2AudioTM GR70 is a fully self-contained 70 watts per channel digital amplifier module. The module enables rapid system design for manufacturers of home theater components. The GR70 contains a high-performance digital switching controller, MOSFET output stages, and high-quality output filter stages. The module is encased in an EMI-shielded package and tested for compliance with agency regulations to assist FCC Class-B, UL, CSA, and CE certification. The GR70 is capable of driving up to 7 channels at 70 watts into an 8-ohm load with all channels driven per FTC specifications.A configurable audio signal processor provides equalization, volume control, tone control, compression, and limiting.A powered second zone allows for a fully independent amplifier zone. The amplifier can be dynamically configured as 7 channels or 5 channels with a stereo second zone. The second zone supports a stereo analog input or a fully independent digital audio input. A separate digital audio output is also provided for the primary channels. D2AUDIO GR70Complete digital amplifier for home theater components70 watts/channelUp to 7 channelsPure digital audio signal path96dB dynamic rangeConfigurable audio processingPowered 2nd Zone90% efficientGraceful protection and recovery GR70 (DPR1005) DATA SHEETSDPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon www.freeservicemanuals.infoIts Freewww.freeservicemanuals.infoCONSUMERGR70 Data Sheet Aug 26, 2003 v1.823SPECIFICATIONS3.1ABSOLUTE MAXIMUM RATINGS 3SPECIFICATIONS3.1ABSOLUTE MAXIMUM RATINGS Operation at or beyond the Absolute Maximum Ratings may result in permanent damage. Normal operation outside of the limits defined in this specification is not implied. 3.2ELECTRICAL CHARACTERISTICS3.2ELECTRICAL CHARACTERISTICSTA = 25 C, HV=38V, LV=12V, SV=7.5V, Ground = 0VParameterConditionMin MaxUnitHigh Voltage Supply (HV)+38V DC Supply 40VLow Voltage Supply (LV)+12V DC Supply 12.5VSignal Voltage Supply (SV)+7.5V DC Supply 8.0VDigital Input Signal Level1MCLK, SCLK,LRCLK,SDI4:1, Z2_MCLK, Z2_LRCK, Z2_ SCLK, Z2_SDI, SDA, SCL, /PWRDWN, /RESET, Z2_EN, Z2_AD, MD0, MD1 -0.6 3.90VAnalog Input Signal Level2Peak to peak AC voltage 5VInput Current, any pin but supplies +/-10mAOperating Temperature Range 0 50CStorage Temperature Range-20 60CLead TemperatureSoldering 10 Seconds 300CMechanical ShockAny Axis non repetitive TBDGMechanical ShockAny Axis Repetitive TBDGElectrostatic DischargeMachine Model TBDkVNote 1: -0.6V undershoots and 3.9V overshoots allowed for 4ns maximumNote 2: Analog inputs are terminated with 10k ohms to analog ground, then AC coupled internallyTABLE 2: Absolute Maximum RatingsSymbolConditionMin Typ MaxUnitVIL 0.8VVIHInputs except /RESET and /PWRDWN 2.0VVIH/RESET and /PWRDWN 3.0VVOH2 mA Load 2.4VVOL2 mA Load 0.4VILInput Leakage - CMOS pins MCLK, LRCLK, SCLK, SDI, Z2_MCLK, Z2_LRCLK, Z2_SCLK, Z2_SDI +/-10uAICInput current on digital inputs with resistive pulls - /PWRDWN, /RESET, Z2_EN, Z2_AD_EN, MD0, MD1, SDA, SCL +/-0.4mARIAnalog input resistance - all analog audio inputs 10k OhmsZSAnalog source output impedance 100OhmsTABLE 3: Electrical CharacteristicsDPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon www.freeservicemanuals.infoIts Freewww.freeservicemanuals.infoCONSUMER5GR70 Data Sheet Aug 26, 2003 v1.823.3PERFORMANCE CHARACTERISTICS3.3PERFORMANCE CHARACTERISTICSResistance load = 8, HV=38V, LV=12V, SV=7.5V 3.4DC POWER REQUIREMENTS 3.4DC POWER REQUIREMENTS TA = 25C, HV=38V, LV=12V, SV=7.5V, Ground = 0VSpecificationConditionMin Typ MaxUnitOutput PowerAll channels driven, FTC3 70 70WFrequency Response20 Hz to 24 kHz, at 1W output power -0.5 0.5dBDynamic Range-60 dB input 1kHz -96dBOutput Distortion (THD+N)20 Hz to 24 kHz, at 1W output power, MPC control bit off 0.12 0.15%Note 3: FTC spec: 30 minute pre-soak at 1/8th power, full power for 5 minutes, all channels driven simultaneously. TABLE 4: Performance CharacteristicsSymbolDescriptionConditionMin Typ MaxUnitHV4High Voltage Supply 38V+12VDC+12V Supply11.75 12 12.5V+7.5VDC+7.5V Supply7.0 7.5 TBDVTsrHVHigh Voltage Supp