HarmanKardon-AVR1700-avr-sm维修电路原理图.pdf

harman/kardon Service ManualAVR1700Audio/Video Receiver CONTENTSESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.10 CONNECTIONS/INSTALLATION.12OPERATION.18TROUBLESHOOTING GUIDE.22 REMOTE & PROCESSOR RESETS.22DISASSEMBLY.23 UNIT EXPLODED VIEW.24 AMP BIAS ADJUSTMENT.25 BLOCK DIAGRAM.26 PCB DRAWINGS.28 ELECTRICAL PARTS LIST.40 SCHEMATICS.85WIRING DIAGRAM.97 harman/kardon Released 2012 8500 Balboa Blvd. Discontinued XXXX Northridge, CA. 91329 Rev0 9/2012 1RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :AVR1700 harman/kardonharman/kardon2RadioFans.CN 收音机爱 好者资料库SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60Hz outlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundAVR1700 harman/kardonharman/kardon3SpecificationsAudio SectionStereo power:100W per channel, two channels driven 6/8 ohms, ?Multichannel power:100 watts per channel two channels driven ?Input sensitivity/impedance:250mV/27k ohmsSignal-to-noise ratio (IHF-A):100dBSurround system adjacent-channel separation:Dolby Pro Logic/PLII: 40dB Dolby Digital: 55dB DTS: 55dBFrequency response:?High instantaneous-current capability (HCC): ?Transient intermodulation distortion (TIM):UnmeasurableFM Tuner SectionFrequency range:?Usable sensitivity IHF:1.3V/13.2dBfSignal-to-noise ratio (mono/stereo):70dB/68dBDistortion (mono/stereo):?Stereo separation:?70dBImage rejection:80dBIF rejection:80dBAM Tuner SectionFrequency range:?(AVR 1700) ?(AVR 170/AVR 170/230C)Signal-to-noise ratio:38dBUsable sensitivity (loop):500V?30dBVideo SectionTelevision format:NTSC (AVR 1700); PAL (AVR 170/AVR 170/230C)Input level/impedance:1Vp-p/75 ohmsOutput level/impedance:1Vp-p/75 ohmsVideo frequency response (composite video):?HDMI:witn 3D and 12-bit Deep ColorGeneral SpecificationsPower requirement:? (AVR 1700); ? (AVR 170/AVR 170/230C)Power consumption (maximum):260W (AVR 1700) 240W (AVR 170/ AVR 170/230C) ?Dimensions (W x H x D): 17-5/16 x 6-1/2 x 14-13/16 (440mm x 165mm x 377mm)Weight12.8 lb (5.8kg)AVR1700 harman/kardonharman/kardon42. Package DrawingAVR1700POLY BAGNODESCRIPTIONPARTS NO.Q,ty123456711CPB1A190ZPOLY BAG1. Instruction manual assy - Accessories(CQXAVR1700)SHEET,QUICK START GUIDE8CQE1A560Z1CABR03P3PBCSA1A039ZANT, AM LOOPBATTERY13FM 1 POL ANTCSA1A018Z12BATTERY ASSY43AM LOOP ANTENNA ASSYSHEET,QUICK START GUIDE6FM 1 POLE ANT(UL)8959REMOCON ASSYCARTAVR1700-HK11TRANSMITTER ASSYREMOCON7STAPLESTAPLECPL090531111CJA2A119ZCORD,POWER1CORD,POWER(UL)SHEET,IMPORTANT1010SHEET,IMPORTANTCQE1A522Z1MICROPHONE ASSYSNOW PAD (R)3BOX ,OUT CARTON5SET4SNOW PAD (L)2MANUAL ASSY1ACCESSORYBOX,OUT CARTON341DESCRIPTIONNOCPS1A920CQXAVR1700CPG1A967W111Q,tyPARTS NO.CPS1A921PAD,RIGHT21PAD,LEFTSETAVR1700SET15CARD WARRANTYCQE1A172X1CARD WARRANTYMICRO PHONE ASSYCJXAVR365MICRO1AVR1700 harman/kardonharman/kardon5Front-Panel ControlsPower Indicator/ Power ButtonMessage DisplayVolume KnobSurround Mode Select ButtonsSet ButtonIR SensorChannel Level Control ButtonSource Select ButtonsLeft/Right ButtonsHeadphone Jack/ ? ConnectorTuning Mode Button/ RDS ButtonDigital Input ButtonSurround-Mode Category ButtonUp/Down Buttons/ Tuning ButtonsUSB PortAux Analog Audio Input ConnectorAVR1700 harman/kardonharman/kardon6Front-Panel Controls, continuedPower indicator/Power button: The AVR has four different power modes:? Off (Power indicator not illuminated): When the rear-panel Main Power switch is in the Off position or the power cord is unplugged the AVR is off and will not respond to any commands. Plugging the power cord into a live AC outlet and setting the Main Power switch in the On position will put the AVR into the Eco Standby mode.? Eco Standby (Power indicator glows solid amber):?energy consumption when youre not using the AVR. When the AVR is in Eco Standby, it will not automatically turn on or play audio in response to an AirPlay signal from a networked device. When the AVR is in Eco Standby, pressing the Power button turns it on. To put the AVR into Eco Standby when it is on, press the Power button for more than three seconds. NOTE: The AVR will not automatically enter the Eco Standby mode.? Standby (Power indicator glows solid amber): The Standby mode mutes the AVR and shuts off its front-panel display, but allows the AVR to automatically turn on and play audio in response to an AirPlay signal from a networked device. See Listening to Media via AirPlay, on page 22, for more information. When the AVR is in Standby, pressing the Power button turns it on. To put the AVR into Standby when it is on, press the Power button for less than three seconds. NOTE: The AVR will automatically enter the Standby mode whenever no control buttons have been pressed and no audio signal has been present for 30 minutes.? On (Power indicator glows solid white): When the AVR is on it is fully operational.IMPORTANT NOTE: If the PROTECT message ever appears on the AVRs front-panel Message display, turn off the AVR and unplug it from the AC outlet. Check all speaker wires for a possible short circuit (the “+” and “” conductors touching each other or both touching the same piece of metal). If a short circuit is not found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.Tuning Mode button (AVR 1700 only): This button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned in.RDS button (AVR 170 only): When listening to an FM radio station that broadcasts RDS information, this button activates the various RDS functions. NOTE: RDS service may not be available in all areas.Channel Level Control button: Press this button to activate the channel-level adjustment feature. After pressing this button, use the Up/Down buttons to select the channel for adjustment and use the Left/Right buttons to adjust the channels level.Digital Input button: Press this button to change the audio input for the current source. Use the Left/Right buttons to cycle through the available input connections, and press the Set button to assign the currently-displayed connection to the source. IR sensor: This sensor receives infrared (IR) commands from the remote control. It is important to ensure that the sensor is not blocked. Set button: Press this button to select the currently highlighted menu item.Left/Right buttons: Use these buttons to navigate the AVRs menus.Message display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. When the on-screen display menu system (OSD) is in use, the current menu settings appear.Up/Down buttons/Tuning buttons: Use these buttons to navigate the AVRs menus. When the radio is the active source, use these buttons to tune stations according to the setting of the Tuning Mode button (see above).Surround-Mode Category button: Press this button to select a surround-sound category. Each press changes the surround-mode category: Auto Select, Virtual, Stereo, Movie, Music and Video Game. To change the specific surround-sound mode within the category, use the Surround Mode Select buttons. See Audio Processing and Surround Sound, on page 23, for more information on surround modes.Surround-Mode Select buttons: After you have selected the desired surround-mode category, press these buttons to select a specific mode within the category, such as to change from Dolby Pro Logic II Movie mode to Logic 7 Movie mode. Surround-mode availability depends on the nature of the source input signal, i.e., digital versus analog, and the number of channels encoded within the signal.Source Select buttons: Press these buttons to select the active source.Headphone jack/EzSet/EQ Mic connector: Connect a 1/4 stereo headphone plug to this jack for private listening. This jack is also used to connect the supplied microphone ? ? ? ? ? ? Configure the AVR for Your Speakers, on page 17.USB port: The USB port can be used to play audio files from an Apple iOS device connected to the port, and can also be used to play MP3 and WMA audio files from a USB device inserted into the port. Insert the connector or device into the USB port oriented so it fits all the way into the port. You may insert or remove the connector or device at any time - there is no installation or ejection procedure.You can also use the USB port to perform firmware upgrades. If an upgrade for the AVRs operating system is released in the future, you will be able to download it to the AVR using this port. Complete instructions will be provided at that time.IMPORTANT: Do not connect a PC or other USB host/controller to this port, or you may damage both the AVR and the other device. HDD is not supported.Volume knob: Turn this knob to raise or lower the volume.Aux Analog Audio Input connector: Connect an auxiliary source component that will be used only temporarily, such as a camcorder, portable music player or game console, here.AVR1700 harman/kardonharman/kardon7Rear-Panel ConnectorsHDMI Input ConnectorsHDMI Monitor Out ConnectorRadio Antenna ConnectorsSubwoofer ConnectorAnalog Audio Input/Output ConnectorsSpeaker ConnectorsComposite Video Input ConnectorsComposite Video Monitor Output ConnectorsMain Power SwitchAC Input ConnectorIR In & Trigger Out ConnectorsNetwork ConnectorRS-232 ConnectorDigital Audio Input ConnectorsAVR1700 harman/kardonharman/kardon8Rear-Panel Connectors, continuedRadio Antenna connectors: Connect the included AM and FM antennas to their respective terminals for radio reception.Analog Audio Input/Output connectors: Use the AVRs Analog Audio Input/Output connectors for source devices that dont have HDMI or digital audio connectors. Use the Rec Out connectors to connect to the audio inputs of a VCR or tape deck. See Connect Your Audio and Video Source Devices, on page 13, for more information.Network connector: Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVRs Network connector to your home network to enjoy Internet radio and content from DLNA-compatible devices that are joined to the network. See Connect to Your Home Network, on page 15, for more information.Subwoofer connector: Connect this jack to a powered subwoofer with a line-level input. See Connect Your Subwoofer, on page 13, for more information.IR In and Trigger Out connectors: When the IR sensor on the front panel is blocked (such as when the AVR is installed inside a cabinet), connect an optional IR receiver to the IR In jack. The Trigger Out connector provides 12V DC whenever the AVR is on. Connect it to the trigger input of a device such as a powered subwoofer.Speaker connectors: Use two-conductor speaker wire to connect each set of terminals to the correct speaker. See Connect Your Speakers, on page 13, for more information.HDMI Input connectors: The HDMI (High-Definition Multimedia Interface) feature is a connection for transmitting digital audio and video signals between devices. If your source devices have HDMI connectors, using them will provide the best possible video and audio performance quality. Since the HDMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via HDMI connections. See Connect Your Audio and Video Source Devices, on page 13