Denon-AVR1609-avr-sm维修电路原理图.pdf

Denon Brand Company, D&M Holdings lnc.eVer. 1SERVICE MANUALAV SURROUND RECEIVERMODELJPE3E2EKE2AE1CEAAVR-1709?AVR-1609? ?AVR-1519? ?AVR-1509?AVR-689?AVR-589?AVC-1509? ?For purposes of improvement, specifications and design are subject to change without notice.Please use this service manual with referring to the operating instructions without fail.Some illustrations using in this service manual are slightly different from the actual set.注意前、必読。本機、火災、感電、対安全性確保、配慮、法的電気用品安全法、所定許可得製造。従際、安全性維持、記載注意事項必守。本機仕様性能改良、予告変更。補修用性能部品保有期間、製造打切後 8 年。修理際、必取扱説明書参照上、作業行。本文中使用、説明都合上現物多少異場合。X0382 V.01 DE/CDM 0806RadioFans.CN 收音机爱 好者资料库2AVR-1709/1609/1519/1509/689/589, AVC-1509Please heed the points listed below during servicing and inspection.Heed the cautions!Spots requiring particular attention when servicing, suchas the cabinet, parts, chassis, etc., have cautions indicatedon labels or seals. Be sure to heed these cautions and thecautions indicated in the handling instructions.Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching in-ternal metal parts when the set is energized couldcause electric shock. Take care to avoid electric shock,by for example using an isolating transformer andgloves when servicing while the set is energized, un-plugging the power cord when replacing parts, etc.(2)There are high voltage parts inside. Handle with extracare when the set is energized.Caution concerning disassembly andassembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if fingers aremoved across them. Use gloves to protect your hands.Only use designated parts!The sets parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In par-ticular, for the important safety parts that are marked z onwiring diagrams and parts lists, be sure to use the desig-nated parts.Be sure to mount parts and arrangethe wires as they were originally!For safety reasons, some parts use tape, tubes or other in-sulating materials, and some parts are mounted away fromthe surface of printed circuit boards. Care is also taken withthe positions of the wires inside and clamps are used tokeep wires away from heating and high voltage parts, sobe sure to set everything back as it was originally.Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected for servicing have been put back in their original po-sitions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insu-lation check on the external metal connectors and betweenthe blades of the power plug, and otherwise check thatsafety is ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnectthe antenna, plugs, etc., and turn the power switch on. Us-ing a 500V insulation resistance tester, check that the in-sulation resistance between the terminals of the powerplug and the externally exposed metal parts (antenna ter-minal, headphones terminal, microphone terminal, inputterminal, etc.) is 1M or greater. If it is less, the set mustbe inspected and repaired.Concerning important safetypartsMany of the electric and structural parts used in the sethave special safety properties. In most cases these prop-erties are difficult to distinguish by sight, and using re-placement parts with higher ratings (rated power andwithstand voltage) does not necessarily guarantee thatsafety performance will be preserved. Parts with safetyproperties are indicated as shown below on the wiring dia-grams and parts lists is this service manual. Be sure to re-place them with parts with the designated part number.(1) Schematic diagrams . Indicated by the z mark.(2) Parts lists . Indicated by the z mark.Using parts other than the designatedparts could result in electric shock, fires orother dangerous situations.SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of thepower cord is less than 460 kohms, the unit is defective.CAUTIONCAUTIONRadioFans.CN 收音机爱 好者资料库3AVR-1709/1609/1519/1509/689/589, AVC-1509、点検時注意願。注意事項守！特注意必要個所、 部品、 捺印注意事項表示。 注意書取扱説明書注意事項必守。感電注意！(1) 、交流電圧印加通電時内部金属部触感電。従通電時、絶縁使用手袋着用、部品交換、電源抜感電注意。(2) 内部高電圧部分、通電時取扱十分注意。分解、組立作業時注意！板金部品端面、部品製造時充分管理、 板金端面鋭利箇所有、 部品端面触指動怪我場合十分注意作業下。 手保護手袋着用。指定部品使用！部品難燃性耐電圧安全上特性持。 従交換部品、 使用同特性部品使用。特配線図、部品表 z 印指定安全上重要部品必指定使用。部品取付配線引、 元！安全上、絶縁材料使用、基板浮取付部品。 内部配線引発熱部品高圧部品接近配慮、 必元。後安全点検！取外、 部品、 配線元、 個所周辺劣化点検、 外部金属端子部、 電源刃間絶縁、安全性確保確認。（絶縁方法）電源電源抜、 外、電源入。500V 絶縁抵抗計用、 電源端子外部露出金属部端子、端子、端子、入力端子間、絶縁抵抗値 M 以上確認。 値以下点検修理必要。安全上重要部品本機使用多電気部品、 機構部品安全上、 特別特性持。 特性場合、 外観判別、 部品高定格（定格電力、耐圧）持使用安全性維持、 限。 安全上特性持部品、 配線図、 部品表表示必指定部品番号使用願。(1) 配線図 z 表示。(2) 部品表 z 表示。指定部品異使用場合、感電、火災危険生恐。注意注意4AVR-1709/1609/1519/1509/689/589, AVC-1509DIMENSION AVR-1709 model 5AVR-1709/1609/1519/1509/689/589, AVC-1509 AVR-1609/1509/1519 model 6AVR-1709/1609/1519/1509/689/589, AVC-1509 AVR-689 model 7AVR-1709/1609/1519/1509/689/589, AVC-1509 AVR-589 model 8AVR-1709/1609/1519/1509/689/589, AVC-1509整形図調整部品交換等、類結束移動場合、作業完了時点整形。正整形発生原因。上面整形WIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly asthey were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noisegeneration.Wire arrangement viewed from the topBack Panel sideFront Panel side9AVR-1709/1609/1519/1509/689/589, AVC-1509DISASSEMBLY Disassemble in order of the arrow of the figure of following flow.下記図矢印順番。 In the case of the re-assembling, assemble it in order of the reverse of the following flow.再組立場合、下記逆順番組立 In the case of the re-assembling, observe attention of assembling it.再組立場合、 組立注意遵守。CABINET TOPPANEL FRONT SUB ASSYHDMI P.W.B ASSYCHASSIS BACK SUB ASSYRefer to DISASSEMBLYRefer to DISASSEMBLYRefer to DISASSEMBLY1.PANEL FRONT SUB ASSY 2.HDMI P.W.B ASSY6.CHASSIS BACK SUBASSYand EXPLODED VIEWand EXPLODED VIEWand EXPLODED VIEWPOWER SW P.W.B ASSYHDMI P.W.B ASSY CHASSIS BACK SUB ASSY (Ref. No. of EXPLODED VIEW : 9) (Ref. No. of EXPLODED VIEW : 54) (Ref. No. of EXPLODED VIEW : 70)FUNC P.W.B ASSY (Ref. No. of EXPLODED VIEW : 10)SIRIUS P.W.B ASSYVIDEO P.W.B ASSYFRONT P.W.B ASSYRefer to DISASSEMBLYRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : 11)3.IO OPTION UNIT /7.VIDEO P.W.B ASSYENCORDER P.W.B ASSYand EXPLODED VIEWand EXPLODED VIEW (Ref. No. of EXPLODED VIEW : 13)SIRIUS P.W.B ASSY VIDEO P.W.B ASSYHEAD PHONE P.W.B ASSY (Ref. No. of EXPLODED VIEW : 75) (Ref. No. of EXPLODED VIEW : 53) (Ref. No. of EXPLODED VIEW : 14)V- AUX P.W.B ASSYTUNER PACKINPUT / CPU P.W.B ASSY (Ref. No. of EXPLODED VIEW : 21)Refer to DISASSEMBLYRefer to DISASSEMBLYMIC P.W.B ASSY4.TUNER PACK8.INPUT / CPU P.W.B ASSY (Ref. No. of EXPLODED VIEW : 22)and EXPLODED VIEWand EXPLODED VIEWTUNER PACKCPU P.W.B ASSY (Ref. No. of EXPLODED VIEW : 71) (Ref. No. of EXPLODED VIEW : 51)TRANSINPUT CPU P.W.B ASSYRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : 52)11.TRANSand EXPLODED VIEWSPEAKER P.W.B ASSYMAIN P.W.B SUB ASSYTRANS Refer to DISASSEMBLYRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : 46)5.SPEAKER P.W.B ASSY9.MAIN P.W.B SUB ASSYand EXPLODED VIEWand EXPLODED VIEWSPEAKER P.W.B ASSYMAIN P.W.B ASSY (Ref. No. of EXPLODED VIEW : 55) (Ref. No. of EXPLODED VIEW : 50)2CH P.W.B ASSY (Ref. No. of EXPLODED VIEW : 33)POWER P.W.B SUB ASSYRefer to DISASSEMBLY10.POWER P.W.B SUB ASSYand EXPLODED VIEWPOWER SUPPLY P.W.B ASSY (Ref. No. of EXPLODED VIEW : 56)POWER P.W.B ASSY (Ref. No. of EXPLODED VIEW : 57)Front sidePicture BPicture APicture CPicture DTop viewThe viewpoint of each photograph(photography direction)各図視点(撮影方向)10AVR-1709/1609/1519/1509/689/589, AVC-15091. PANEL FRONT SUB ASSY(1) Remove the screws.（。 ）(2) Disconnect the connector wires and remove the screw.（。 ）proceeding ( 手順 ) : CABINET TOP PANEL FRONT SUB ASSY Bottom viewCORD HOLDER : LooseCP541CP302CN301Top viewcutCORD HOLDER : LooseFFC CABLEPicture C11AVR-1709/1609/1519/1509/689/589, AVC-1509(3) Remove the screw.（。 ）(4) Disconnect the connector wire.（。 ）Please refer to EXPLODED VIEW for the disassembly method of each P.W.B included in PANEL FRONT SUB ASSY .PANEL FRONT SUB ASSY 各基板 EXPLODED VIEW 参照。2. HDMI P.W.B.ASSY(1) Remove the screws.（。 ）Top viewPicture CCN306proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY Picture B12AVR-1709/1609/1519/1509/689/589, AVC-1509(2) Disconnect the connector wires.（。 ）3. SIRIUS P.W.B ASSY(1) Remove the screw.（。 ）(2) Disconnect the connector wire.（。 ）CN803CP905CN806CP904CP404Picture BCP405CN802CN804CN805HDMI P.W.B ASSYproceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY Picture BSIRIUS ASSYPicture BCP90113AVR-1709/1609/1519/1509/689/589, AVC-15094. TUNER PACK(1) Remove the FFC CABLE.（FFC 。 ）(2) Remove the screws.（。 ）proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK Top viewFFC CABLEPicture B14AVR-1709/1609/1519/1509/689/589, AVC-15095. SPEAKER P.W.B ASSY(1) Disconnect the connector wires. （。 ）(2) Remove the screws.（。 ）proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK SPEAKER P.W.B ASSY Top viewcutCP103CP103CP101CP102SPEAKER P.W.B ASSYPicture B15AVR-1709/1609/1519/1509/689/589, AVC-15096. CHASSIS BACK SUB ASSY(1) Remove the screws.（。 ）7. VIDEO P.W.B ASSY(1) Disconnect the connector wires.（。 ）proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK SPEAKER P.W.B ASSY CHASSIS BACK SUB ASSY Picture B?proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK SPEAKER P.W.B ASSY CHASSIS BACK SUB ASSY VIDEO P.W.B ASSY VIDEO P.W.B ASSYPicture DCN1002CN1006CN1003CP514CN100116AVR-1709/1609/1519/1509/689/589, AVC-15098. INPUT / CPU P.W.B ASSY(1) Disconnect the FFC CABLE.（FFC 。 ）(2) Disconnect the connector wires.（。 ）proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK SPEAKER P.W.B ASSY CHASSIS BACK SUB ASSY VIDEO P.W.B ASSY INPUT / CPU P.W.B ASSY FFC CABLEPicture CCPU P.W.B ASSYCP514Picture BINPUT P.W.B ASSYCN704Picture BCN707CN703CN702INPUT P.W.B ASSYCPU P.W.B ASSY17AVR-1709/1609/1519/1509/689/589, AVC-15099. MAIN P.W.B SUB ASSY Please refer to EXPLODED VIEW for the disassembly method of each P.W.B included in MAIN P.W.B ASSY . MAIN P.W.B ASSY 各基板 EXPLODED VIEW 参照。10. POWER P.W.B SUB ASSY (1) Disconnect the connector wires.（。 ）(2) Remove the screws.（。 ）proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK SPEAKER P.W.B ASSY CHASSIS BACK SUB ASSY VIDEO P.W.B ASSY INPUT / CPU P.W.B ASSY MAIN P.W.B SUB ASSY proceeding ( 手順 ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY TUNER PACK SPEAKER P.W.B ASSY POWER P.W.B SUB ASSY Picture CcutCP513CP512CP501CP503CN506CN505POWER P.W.B ASSYPOWER SUPPLY P.W.B ASSYTop view18AVR-1709/1609/1519/1509/689/589, AVC-150911. TRANS(1) Disconnect the connector wires.（。 ） Please refer to EXPLODED VIEW for the disassembly method of POWER TRANS. POWER TRANS EXPLODED VIEW 参照。proceeding ( 手順 ) : CABINET TOP TRANS CP104CN301CP302Top viewCP513CP512CP501Picture Ccut19AVR-1709/1609/1519/1509/689/589, AVC-1509時注意事項AV / 初期化周辺部品、Digital 基板等交換場合、AV / 初期化行下。1.ON/OFF OFF 。2.INPUTMODE SPEAKERS 2 押状態、ON/OFF 押 ON 。3.表示約 1 秒間隔点滅確認後、2 指離。初期化。時使用治具基板修理際、使用治具 ( 延長）下記。必要応販社注文下。00D SPK- 561 EXTENSION UNIT KIT: 1 式00D SPK- 562 9120 CONN. JOINT KIT: 1 式際、使用治具（RS232C 製品内部 変換基板 +8P ) 下記。必要応販社注文。00DSPK-581 WRITING UNIT: 1 式注意 :上記 3 状態場合、一度操作 1直。初期化行客様設定内容工場出荷状態戻、設定内容控初期化後再設定。CAUTION IN SERVICINGInitializing AV SURROUND RECEIVER/AM-PLIFIERAV SURROUND RECEIVER/AMPLIFIER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced.1. Switch off the unit.2. With the INPUTMODE and SPEAKERS buttons pressed, press the ON/OFF button to turn the power on.3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 but-tons and the microprocessor will be initialized.JIG to use for servicingWhen you repair the printing board, you can use the following JIG (Extension cable kit). Please order to Denon Official Ser-vice Distributor in your region if necessary.00D SPK- 561 EXTENSION UNIT KIT: 1 Set00D SPK- 562 9120 CONN. JOINT KIT : 1 SetWhen you update the firmware, you can use the following JIG (RS232C to internal connector conversion adapter with 8P cable kit ). Please order to Denon Official Service Distrib-utor in your region if necessary.00DSPK-581 WRITING UNIT: 1 SetNote:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode.So make sure to m+emorize your setting for re-storing after the initialization.ON/OFFSPEAKERSINPUTMODE20AVR-1709/1609/1519/1509/689/589, AVC-1509DSP 方法DSP 表示1. 動作仕様、DSP 表示 :起動状態、情報表示。起動方法 : E3, E1C, EA, JP DYN VOL VIDEO SELECT 2 押状態、ON/OFF 押電源入。後、STATUS 押 2 項内容 FL Display 表示。 E2 DYN VOL RDS 2 押状態、ON/OFF 押電源入。後、 STATUS押2項内容FL Display表示。2. 表示順序仕向地表示 情報 DSP情報Check mode for com/DSP versioncom/DSP Version Display Mode1. Operation specificationscom/DSP version display mode:When started up, the version information is displayed.Starting up: E3, E1C, EA, JP modelWith the DYN VOL and VIDEO SELECT buttons pressed, press the ON/OFF button to turn the power on.Now, press the STATUS button to the display the 2nd item information on the FL Display. E2 modelWith the DYN VOL and RDS buttons pressed, press the ON/OFF button to turn the power on.Now, press the STATUS button to the display the 2nd item information on the FL Display.2. Display OrderDestination information Main-com version information DSP version informationON/OFFVIDEO SELECTDYN VOLE3, E1C, EA, JP modelSTATUSSTATUSON/OFFRDSDYN VOLE2 model21AVR-1709/1609/1519/1509/689/589, AVC-1509PROCEDURE FOR CHECKING ERRORS (Displaying the protection history)Errors checking mode (Displaying the protection history)1.Operation specificationsError mode (Displaying the protection history):When started up, the error information is displayed.Starting up: All model commonnessWith the SYSTEM SETUP and MULT EQ buttons pressed, press the ON/OFF button to turn the power on. The error (protection history display) mode is set.Now, press the STATUS button to turn on the FL display.2.About the display on the FL displayWhen the STATUS button is pressed after setting the error (protection history display) mode, a history like the one shown below is displayed, depending on the conditions.(1) Normally (when there has been no protection incident)(2) For ASO/DC (when the last protection incident was ASO or DC protection)(3) For THERMAL (when the last protection incident was THERMALprotection)When the STATUS button is pressed