Denon-AVR2312-avr-sm维修电路原理图.pdf

D&M Holdings Inc.SERVICE MANUALeeMODELJPE3E2EKEAE1CE1KCIAVR-2312CIPAVR-2312PPPINTEGRATED NETWORK AV RECEIVERVer. 5S0376-0V05DM/DG1110 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fail. For purposes of improvement, specifications and design are subject to change without notice.sssPlease refer to the MODIFICATION NOTICE.RadioFans.CN 收音机爱 好者资料库2CONTENTSSAFETY PRECAUTIONS .3NOTE FOR SCHEMATIC DIAGRAM .4TECHNICAL SPECIFICATIONS .5DIMENSION .5CAUTIONS IN SERVICING .6Initializing INTEGRATED NETWORK AV RECEIVER .6Service Jig .6DISASSEMBLY .71. FRONT PANEL ASSY .92. HEAT SINK ASSY .103. HDMI UNIT ASSY .124. TRANS MAIN .15SPECIAL MODE .16Special mode setting button .161. com/DSP Version display mode .172. Errors checking mode (Displaying the protection history) .203. Remote ID Setup mode .22PROTECTION DIAGRAM .234. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) .24BLOCK DIAGRAM .29JIG FOR SERVICING .59WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE .63PROCEDURE FOR UPGRADING THE VERSION OF THE FIRMWARE .63ADJUSTMENT .70SURROUND MODES AND PARAMETERS .71TROUBLE SHOOTING .751. POWER .752. Analog video .763. HDMI/DVI .824. AUDIO .915. Network/USB .946. SMPS .97CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK .100LAEVEL DIAGRAM .101PRINTED WIRING BOARDS .1077CH AMP (COMPONENT SIDE) .1077CH AMP (FOIL SIDE) .107SPMS (COMPONENT SIDE) .108SMPS (FOIL SIDE) .108SPK_PREOUT (COMPONENT SIDE) .109SPK_PREOUT (FOIL SIDE) .110INPUT (COMPONENT SIDE) .111INPUT (FOIL SIDE) .112FUSE (COMPONENT SIDE).113RS232C_CNT (COMPONENT SIDE) .113FUSE (FOIL SIDE) .113RS232C_CNT (FOIL SIDE) .113POSISTOR (COMPONENT SIDE) .113POSISTOR (FOIL SIDE) .113FRONT (COMPONENT SIDE) .114V.AUX (FOIL SIDE) .114FRONT (FOIL SIDE) .114V.AUX (COMPONENT SIDE) .114HDMI FFC (COMPONENT SIDE) .115GUIDE TOP (COMPONENT SIDE).115GUIDE L (COMPONENT SIDE) .115HDMI FFC (FOIL SIDE) .115GUIDE TOP (FOIL SIDE) .115GUIDE L (FOIL SIDE) .115USB (COMPONENT SIDE) .115HP (COMPONENT SIDE) .115GUIDE R (COMPONENT SIDE) .115USB (FOIL SIDE) .115HP (FOIL SIDE) .115GUIDE R (FOIL SIDE) .115SELECTOR (COMPONENT SIDE) .116RS232C (COMPONENT SIDE).116SELECTOR (FOIL SIDE) .116RS232C (FOIL SIDE) .116SIDE_CNT (COMPONENT SIDE) .117SIDE_CNT (FOIL SIDE) .117VIDEO (COMPONENT SIDE) .118VIDEO (FOIL SIDE) .119FRONT CNT (COMPONENT SIDE) .120FRONT CNT (FOIL SIDE) .121HDMI (COMPONENT SIDE) .122HDMI (FOIL SIDE) .123SCHEMATIC DIAGRAMS .124USB UNIT.124FRONT UNIT .124AMP UNIT (1/2) .125AMP UNIT (2/2) .126SPK/PREOUT/REG UNIT (1/4).127SPK/PREOUT/REG UNIT (2/4).128SPK/PREOUT/REG UNIT (3/4).129FRONT_CNT UNIT .130CNT/RS232C UNIT (1/4).131CNT/RS232C UNIT (2/4).132CNT/RS232C UNIT (3/4).133CNT/RS232C UNIT (4/4).134INPUT UNIT .135VIDEO UNIT .136SMPS UNIT .137DIGITAL UNIT (1/16) .138DIGITAL UNIT (2/16) .139DIGITAL UNIT (3/16) .140DIGITAL UNIT (4/16) .141DIGITAL UNIT (5/16) .142DIGITAL UNIT (6/16) .143DIGITAL UNIT (7/16) .144DIGITAL UNIT (8/16) .145DIGITAL UNIT (9/16) .146DIGITAL UNIT (10/16) .147DIGITAL UNIT (11/16) .148DIGITAL UNIT (12/16) .149DIGITAL UNIT (13/16) .150DIGITAL UNIT (14/16) .151DIGITAL UNIT (15/16) .152DIGITAL UNIT (16/16) .153WIRING DIAGRAM .154EXPLODED VIEW .155PARTS LIST OF EXPLODED VIEW .157PACKING VIEW .160PARTS LIST OF PACKING & ACCESSORIES .160SEMICONDUCTORS .1621. ICs .1622. FL DISPLAY.193PARTS LIST OF P.C.B. UNIT .195PCB INPUT ASSY .195PCB FRONT ASSY .197PCB 7CH AMP ASSY .200PCB MAIN ASSY.207PCB CNT ASSY .211PCB VIDEO ASSY .213PCB HDMI ASSY .215PCB SMPS ASSY .224RadioFans.CN 收音机爱 好者资料库3SAFETY PRECAUTIONSThe following items should be checked for continued protection of the customer and the service technician.LEAKAGE CURRENT CHECKBefore returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. Be sure to test for leakage current with the AC plug in both polarities, in addition, when the sets power is in each state (on, off and standby mode), if applicable.CAUTION Please heed the following cautions and instructions during servicing and inspection. Heed the cautions!Cautions which are delicate in particular for servicing are labeled on the cabinets, the parts and the chassis, etc. Be sure to heed these cautions and the cautions described in the handling instructions. Cautions concerning electric shock!(1) An AC voltage is impressed on this set, so if you touch internal metal parts when the set is energized, you may get an electric shock. Avoid getting an electric shock, by using an isolating transformer and wearing gloves when servicing while the set is energized, or by unplugging the power cord when replacing parts, for example.(2) There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly!Through great care is taken when parts were manufactured from sheet metal, there may be burrs on the edges of parts. The burrs could cause injury if fingers are moved across them in some rare cases. Wear gloves to protect your hands. Use only designated parts!The sets parts have specific safety properties (fire resistance, voltage resistance, etc.). Be sure to use parts which have the same properties for replacement. The burrs have the same properties. In particular, for the important safety parts that are indicated by the z mark on schematic diagrams and parts lists, be sure to use the designated parts. Be sure to mount parts and arrange the wires as they were originally placed!For safety seasons, some parts use tapes, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires by arranging them and using clamps to keep them away from heating and high voltage parts, so be sure to set everything back as it was originally placed. Make a safety check after servicing!Check that all screws, parts and wires removed or disconnected when servicing have been put back in their original positions, check that no serviced parts have deteriorate the area around. Then make an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and on the power. Using a 500V insulation resistance tester, check that the insulation resistance value between the inplug and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired.Many of the electric and the structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and the use of replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and the parts list in this service manual. Be sure to replace them with the parts which have the designated part number.(1) Schematic diagrams .Indicated by the z mark.(2) Parts lists .Indicated by the z mark.The use of parts other than the designated parts could cause electric shocks, fires or other dangerous situations.CAUTION Concerning important safety parts4NOTE FOR SCHEMATIC DIAGRAMWARNING:Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.CAUTION:Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.WARNING:DO NOT return the set to the customer unless the problem is identified and remedied.NOTICE:ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHMALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO FARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.Parts indicated by nsp on this table cannot be supplied.When ordering a part, make a clear distinction between 1 and I (i) to avoid mis-supplying.A part ordered without specifying its part number can not be supplied. General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Part indicated by mark is not illustrated in the exploded view.WARNING:1.2.3.4.5.6.ResistorsRD:CarbonRC:CompositionRS :Metal oxide filmRW:windingRN:Metal filmRK :Metal mixtureP:Pulse-resistant typeNL :Low noise typeNB :Non-burning typeFR :Fuse-resistorF:Lead wire forming2B :1/8 W2E :1/4 W2H :1/2 W3A :1 W3D :2 W3F :3 W3H :5 WF:1%G:2%J:5%K:10%M :20%Ex.:RNType14KShapeand per-formance2EPower182Resist-anceGAllowableerrorFROthers* Resistance1800ohm=1.8kohm1 82Indicates number of zeros after effective number.2-digit effective number.1.2ohm1 R22-digit effective number, decimal point indicated by R.1-digit effective number.: Units: ohmNOTE FOR PARTS LIST5TECHNICAL SPECIFICATIONS s n Audio SectionPoweramplifierRated output :Front : 105 W + 105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W + 135 W (6 , 1 kHz with 0.7 % T.H.D.)Center :105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W (6 , 1 kHz with 0.7 % T.H.D.)Surround :105 W + 105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W + 135 W (6 , 1 kHz with 0.7 % T.H.D.)Surround back:105 W + 105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W + 135 W (6 , 1 kHz with 0.7 % T.H.D.)Output connectors : 6 16 AnalogInput sensitivity/Input impedance : 200 mV/47 kFrequency response: 10 Hz 100 kHz +1, 3 dB (DIRECT mode)S/N : 100 dB (IHFA weighted, DIRECT mode) n Video sectionStandard video connectorsInput/output level and impedance : 1 Vp-p, 75 Frequency response : 5 Hz 10 MHz 0, 3 dBColor component video connectorInput/output level and impedance : Y (brightness) signal 1 Vp-p, 75 PB / CB signal 0.7 Vp-p, 75 PR / CR signal 0.7 Vp-p, 75 Frequency response : 5 Hz 60 MHz 0, 3 dB n Tuner section (E3 model)FM(Note: V at 75 , 0 dBf = 1 x 1015 W)Receiving Range : FM 87.5 MHz 107.9 MHz AM520 kHz 1710 kHzUsable Sensitivity :FM1.2 V (12.8 dBf) AM18 V50 dB Quieting Sensitivity:FMMONO 2.0 V (17.3 dBf)S/N (IHF-A) :FMMONO 72 dB AMSTEREO 67 dBTotal harmonic Distortion :FMMONO 0.3 % (1 kHz) AMSTEREO 0.7 % (1 kHz) n Tuner section (E2,EA,E1C model)FM(Note: V at 75 , 0 dBf = 1 x 1015 W)Receiving Range : FM 87.5 MHz 108.0 MHz AM522 kHz 1611 kHzUsable Sensitivity :FM1.2 V (12.8 dBf) AM18 V50 dB Quieting Sensitivity :FMMONO 2.0 V (17.3 dBf)STEREO 34.5 V (42 dBf)S/N :FMMONO 72 dB (IHFA weighted, DIRECT mode)STEREO 67 dB (IHFA weighted, DIRECT mode)Total harmonic Distortion :FMMONO 0.3 % (1 kHz)STEREO 0.7 % (1 kHz) n GeneralPower supply : AC 120 V, 60 Hz (E3 model) AC 230 V, 50/60 Hz (E2,EA model) AC 220 V, 50 Hz (E1C model)Power consumption :600 W0.1 W (Standby)2.2 W (CEC standby)Maximum external dimensions : 435 (W) x 167 (H) x 382 (D)Weight : 11.0 kgDIMENSION34043535.28629.8236.854.7382338.52224521.5151167166CAUTIONS IN SERVICINGInitializing INTEGRATED NETWORK AV RECEIVERINTEGRATED NETWORK AV RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. were replaced.1. Turn off the power pressing ON/STANDBY button.2. Press ON/STANDBY button while simultaneously while pressing PRESET CHANNEL 2 and PRESET CHANNEL 3 buttons.3. Check that the entire display is flashing at intervals of about 1 second, and then release the 2 buttons. The microprocessor will be initialized.Service Jig dWhen you repair the printing board, you can use the following JIG (Extension cable kit).Please order it from Denon Official Service Distributor in your region if necessary.8U-110084S : EXTENSION UNIT KIT : 1 Set(Refer to 59 page.)Note: If step 3 fails, start over from step 1. All user settings will be lost and the factory setting will be recovered after the set is initialized. So make sure to note down your setting beforehand for restoring after the initialization.ON/STANDBYPRESET CHANNEL 2PRESET CHANNEL 37DISASSEMBLY Disassemble in order of the arrow in the following figure. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe attention of assembling. If wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.FRONT PANEL ASSYRefer to DISASSEMBLY 1. FRONT PANEL ASSYand EXPLODED VIEWPCB V.AUX_VOL(Ref. No. of EXPLODED VIEW : C1)PCB HP(Ref. No. of EXPLODED VIEW : C2)PCB USB(Ref. No. of EXPLODED VIEW : C3)PCB FRONT(Ref. No. of EXPLODED VIEW : C4)PCB SELECTOR(Ref. No. of EXPLODED VIEW : C5)PCB HDMI FFC GUIDE(Ref. No. of EXPLODED VIEW : C6)PCB FRONT HDMI(Ref. No. of EXPLODED VIEW : C25)POWER TRANSRefer to DISASSEMBLY 4. POWER TRANSand EXPLODED VIEWPOWER TRANS(Ref. No. of EXPLODED VIEW : C23)CABINET TOPHEAT SINK ASSYRefer to DISASSEMBLY 2. HEAT SINK ASSYand EXPLODED VIEWPCB GUIDE R(Ref. No. of EXPLODED VIEW : C7)PCB GUIDE L(Ref. No. of EXPLODED VIEW : C8)PCB GUIDE TOP(Ref. No. of EXPLODED VIEW : C9)PCB 7CH_AMP ASSY(Ref. No. of EXPLODED VIEW : C10)HDMI UNIT ASSYRefer to DISASSEMBLY 3. HDMI UNIT ASSYand EXPLODED VIEWPCB FRONT CNT(Ref. No. of EXPLODED VIEW : C11)PCB SIDE CNT(Ref. No. of EXPLODED VIEW : C12)PCB RS232C(Ref. No. of EXPLODED VIEW : C13)PCB SPK_PREOUT(Ref. No. of EXPLODED VIEW : C14)PCB RS232C CNT(Ref. No. of EXPLODED VIEW : C15)PCB FUSE(Ref. No. of EXPLODED VIEW : C16)PCB F_WIDE(Ref. No. of EXPLODED VIEW : C17)PCB INPUT(Ref. No. of EXPLODED VIEW : C18)PCB VIDEO ASSY(Ref. No. of EXPLODED VIEW : C20)PCB HDMI(Ref. No. of EXPLODED VIEW : C22)8About the photos used for descriptions of the DISASSEMBLY section The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as Shooting direction: *. Refer to the diagram below about the shooting direction of each photograph. Photographs with no shooting direction indicated were taken from the top of the set. The photograph is AVR-2312CIE3 model. The viewpoint of each photograph(Shooting direction)View from the topFront sideShooting direction: BShoot