Denon-AVC3310-avr-sm维修电路原理图.pdf

Denon Brand Company, D&M Holdings lnc.eX0425 V.04 DE/CDM 0909SERVICE MANUALAV SURROUND RECEIVERAV SURROUND AMPLIFIERMODELJPEUECE2E3E2AE1CEUTAVR-3310CI?AVR-3310? ?AVR-990? ?MODELJPEUECE2E3E2AE1CEUTAVC-3310? ?sssVer. 4For purposes of improvement, specifications and design are subject to change without notice.Please use this service manual with referring to the operating instructions without fail.Some illustrations using in this service manual are slightly different from the actual set.Please refer to theMODIFICATION NOTICE.RadioFans.CN 收音机爱 好者资料库2AVR-3310CI/AVR-3310/AVR990/AVC-3310Please heed the points listed below during servicing and inspection.Heed the cautions!Spots requiring particular attention when servicing, suchas the cabinet, parts, chassis, etc., have cautions indicatedon labels or seals. Be sure to heed these cautions and thecautions indicated in the handling instructions.Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching in-ternal metal parts when the set is energized couldcause electric shock. Take care to avoid electric shock,by for example using an isolating transformer andgloves when servicing while the set is energized, un-plugging the power cord when replacing parts, etc.(2)There are high voltage parts inside. Handle with extracare when the set is energized.Caution concerning disassembly andassembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if fingers aremoved across them. Use gloves to protect your hands.Only use designated parts!The sets parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In par-ticular, for the important safety parts that are marked z onwiring diagrams and parts lists, be sure to use the desig-nated parts.Be sure to mount parts and arrangethe wires as they were originally!For safety reasons, some parts use tape, tubes or other in-sulating materials, and some parts are mounted away fromthe surface of printed circuit boards. Care is also taken withthe positions of the wires inside and clamps are used tokeep wires away from heating and high voltage parts, sobe sure to set everything back as it was originally.Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected for servicing have been put back in their original po-sitions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insu-lation check on the external metal connectors and betweenthe blades of the power plug, and otherwise check thatsafety is ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnectthe antenna, plugs, etc., and turn the power switch on. Us-ing a 500V insulation resistance tester, check that the in-sulation resistance between the terminals of the powerplug and the externally exposed metal parts (antenna ter-minal, headphones terminal, microphone terminal, inputterminal, etc.) is 1M or greater. If it is less, the set mustbe inspected and repaired.Concerning important safetypartsMany of the electric and structural parts used in the sethave special safety properties. In most cases these prop-erties are difficult to distinguish by sight, and using re-placement parts with higher ratings (rated power andwithstand voltage) does not necessarily guarantee thatsafety performance will be preserved. Parts with safetyproperties are indicated as shown below on the wiring dia-grams and parts lists is this service manual. Be sure to re-place them with parts with the designated part number.(1) Schematic diagrams . Indicated by the z mark.(2) Parts lists . Indicated by the z mark.Using parts other than the designatedparts could result in electric shock, fires orother dangerous situations.SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of thepower cord is less than 460 kohms, the unit is defective.CAUTIONCAUTIONRadioFans.CN 收音机爱 好者资料库3AVR-3310CI/AVR-3310/AVR990/AVC-3310DIMENSIONAVR-3310CI/AVR-3310/AVR-990/AVC-331034443415515.5170.520.7244.5372.820.541454.74AVR-3310CI/AVR-3310/AVR990/AVC-3310WIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly asthey were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noisegeneration.Wire arrangement viewed from the topExcept AVR-3310CI, AVR-990 modelsdFront Panel sideBack Panel side5AVR-3310CI/AVR-3310/AVR990/AVC-3310CAUTION IN SERVICINGBefore the Digital P.W.B. are replacedIf you cannot specify the cause of the digital PWB defect, carry out Initializing Update to latest firmware. The defect may be cleared. See the following for the method of initializing the com.Initializing AV SURROUND RECEIVERAV SURROUND RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced.1. Switch off the unit.2. Hold the following STANDARD button and DSP SIMULATION button, and switch on the unit.3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized.Note:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode.So make sure to memorize your setting for restoring after the initialization.JIG to use for servicingWhen you repair the printing board, you can use the following JIG. Please order to Denon Official Service Distributor in your region if necessary.Extention cable kit00D SPK- 561 EXTENSION UNIT KIT : 1 Set00D SPK- 562 TUCP CONN. JOINT KIT : 1 SetExtention cable for Idling CurrentParts Number for Extension Cables and Quantity of Unit. How to use and Adjust Idle Current.1. The thin and hard plate (ex. Ruler) is fixed with the tape behind the cable. 2. The voltmeter is connected with the other side of the extension cable.3. Refer to ADJUSTMENT(Idling Current).Parts NumberParts NameQty / unitRemarks612050082004D6P 250mm NH1L=250mm 6P NH Cable612050083007D8P 250mm NH1L=250mm 8P NH Cable1,22,36AVR-3310CI/AVR-3310/AVR990/AVC-3310DISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe attention of assembling it.TOP COVERDIGITAL UNIT ASSYFRONT PANEL UNIT ASSYRefer to DISASSEMBLYREG UNITRefer to DISASSEMBLY2. DIGITAL UNIT ASSYRefer to DISASSEMBLY1.FRONT PANEL UNIT ASSYand EXPLODED VIEW5. REG UNITP.SW UNITDIGITAL UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-8) (Ref. No. of EXPLODED VIEW : G)REG UNIT FRONT USB UNIT (Ref. No. of EXPLODED VIEW : B-4) (Ref. No. of EXPLODED VIEW : E-3)REG CONNECT-1 UNITMIC UNITBACK PANEL UNIT ASSY (Ref. No. of EXPLODED VIEW : A-15) (Ref. No. of EXPLODED VIEW : A-9)Refer to DISASSEMBLYCONNECT UNIT-2FRONT IN UNIT3. BACK PANEL UNIT ASSY (Ref. No. of EXPLODED VIEW : D-4) (Ref. No. of EXPLODED VIEW : A-10)PTC UNITVR CONNECT UNIT (Ref. No. of EXPLODED VIEW : A-5)A.VIDEO UNIT, A.AUDIO UNIT VOLUME UNITand RADIATOR UNIT ASSYSPEAKER UNIT (Ref. No. of EXPLODED VIEW : A-4)Refer to DISASSEMBLYRefer to DISASSEMBLYFUNC CONNECT UNIT4. A.VIDEO UNIT, A.AUDIO UNIT6. AMP UNIT (Ref. No. of EXPLODED VIEW : A-7)and RADIATOR UNIT ASSYand EXPLODED VIEWFUNC UNITand EXPLODED VIEWSPEAKER UNIT (Ref. No. of EXPLODED VIEW : A-6)A.VIDEO UNIT (Ref. No. of EXPLODED VIEW : D-1)FLD UNIT (Ref. No. of EXPLODED VIEW : E-1) (Ref. No. of EXPLODED VIEW : A-1)A.AUDIO UNIT (Ref. No. of EXPLODED VIEW : E-2)AMP CONNECT UNITMAIN CPU UNITRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : F)7. AMP CONNECT UNITREMOTE/IPOD UNITand EXPLODED VIEW (Ref. No. of EXPLODED VIEW : B-5)AMP CONNECT UNIT232C UNIT (Ref. No. of EXPLODED VIEW : D-2) (Ref. No. of EXPLODED VIEW : B-6)P.AMP UNITRefer to DISASSEMBLY9.P.AMP UNITand EXPLODED VIEWP.AMP UNIT (Ref. No. of EXPLODED VIEW : C-17)dsdd7AVR-3310CI/AVR-3310/AVR990/AVC-3310About the photos used for descriptions in the “DISASSEMBLY” section. The direction from which the photographs used herein were photographed is indicated at Direction of photograph: * at the left of the respective photographs. Refer to the table below for a description of the direction in which the photos were taken. Photographs for which no direction is indicated were taken from above the product.1. FRONT PANEL UNIT ASSY(1) Remove the screws.(2) Cut the wire clampers then disconnect the connector wires. Front sideDirection of photograph: BDirection of photograph: DDirection of photograph: CDirection of photograph: AThe viewpoint of each photograph(Photografy direction)View from aboveExcept AVR-3310CI, AVR-990 modelsdProceeding:TOP COVER FRONT PANEL UNIT ASSYView from bottomdExcept EUEC modelcutcutCX021CY052Direction of photograph: Ds8AVR-3310CI/AVR-3310/AVR990/AVC-3310(3) Disconnect the FFC Cables.(4) Remove the screwsAttention of assemblingWhen mounting the FRONT PANEL ASSY on the CHASSIS, do so with the DOOR open so as to prevent breaking the EARTH PLATE(DOOR).If the FRONT PANEL ASSY is mounted on the chassis with the DOOR closed, the EARTH PLATE(DOOR) willhit the CHASSIS and break.Direction of photograph: CFFC Cable?ddsPlease refer to EXPLODED VIEW for the disassembly method of each P.W.B included in FRONT PANEL ASSY.DOOR openDOOR closed (EARTH PLATE (DOOR) will be broken.)EARTH PLATE (DOOR)DOORDOOREARTH PLATE (DOOR)Direction of photograph: ADirection of photograph: Ad9AVR-3310CI/AVR-3310/AVR990/AVC-33102. DIGITAL UNIT ASSY (1) Remove the screws.(2) Remove the alminium tape, then cut the wire clampers. Disconnect the connector wire, FFC Cables, and board to board.3. BACK PANEL UNIT ASSYRemove the Sheets, then remove the screws.Proceeding:TOP COVERDIGITAL UNIT ASSY?Direction of photograph: AExcept EUEC modelFFC CableFFC CableFFC CablecutcutMAIN CPU UNITDIGTAL UNIT ASSYBoard to boardCX047CY052Alminium TapesProceeding:TOP COVERDIGITAL UNIT ASSY BACK PANEL UNIT ASSYSheetsView from bottom10AVR-3310CI/AVR-3310/AVR990/AVC-3310Remove the screws.?Direction of photograph: A?Direction of photograph: AEUEC modelE2 model?Direction of photograph: AE1C modelsd11AVR-3310CI/AVR-3310/AVR990/AVC-3310(3) Disconnect the connector wires and FFC Cable, then remove the screws. (4) Remove the PWB HOLDER. Disconnect the connector wire and FFC Cable.Except AVR-3310CI, AVR-990 modelCX055CX074Style pin : LooseStyle pin : LooseCord holder : LooseCX091sdFFC CableCX068PWB HOLDERDirection of photograph: Cd12AVR-3310CI/AVR-3310/AVR990/AVC-33104. A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY(1) Disconnect the board to board and FFC Cable.(2) Disconnect the connector wires.Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSYDIGITAL UNIT ASSYdvDirection of photograph: CDirection of photograph: CMAIN CPU UNITMAIN CPU UNITFFC CableCY034Except E1C modelE1C modeldCX073CX19213AVR-3310CI/AVR-3310/AVR990/AVC-3310(3) Remove the screws.5. REG UNIT (1) Disconnect the board to board and connector wires. Remove the Filament Tape.Direction of photograph: AA.VIDEO UNITA.AUDIO UNITRADIATOR UNIT ASSYDirection of photograph: AA.VIDEO UNITE2 modelEUEC modelA.AUDIO UNITRADIATOR UNIT ASSYsddProceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSYDIGITAL UNIT ASSY REG UNITdBoard to boardDirection of photograph: ACX231CX092vFilament TapeHOTMELT14AVR-3310CI/AVR-3310/AVR990/AVC-3310(2) Disconnect the connector wires, then remove the screws.6. SPEAKER UNIT(1) Disconnect the VH connector and conector.7. AMP CONNECT UNIT(1) Disconnect the connector.PTC UNIT?Direction of photograph: AsProceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSYDIGITAL UNIT ASSY REG UNIT SPEAKER UNITdCX851CX891CX876CX874CX871CX873CX872CX875CX877View from bottomProceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSYDIGITAL UNIT ASSY REG UNIT SPEAKER UNIT AMP CONNECT UNITdCX803CX805CX806CX811CX812CX807CX804Direction of photograph: Ass15AVR-3310CI/AVR-3310/AVR990/AVC-33108. P.AMP UNIT(1) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSYDIGITAL UNIT ASSY REG UNIT P.AMP UNIT SPEAKER UNIT AMP CONNECT UNITdDirection of photograph: Bs16AVR-3310CI/AVR-3310/AVR990/AVC-3310SPECIAL MODESpecial mode setting button Press the ON/OFF button to turn on while pressing both buttons A and B at the same time.Note:If is displayed on the fluorescent display, the unit is set to the special developers mode and RS-232C com-munications are not possible.Press and hold in the STATUS and buttons for over 3 seconds with the power turned on to turn the display off. RS-232C communications are now enabled.ModeButton AButton BcontentsVersion display(com/DSP Error Display)STATUSRETURNSerial No. and firmware versions such as Main, Sub, DSP are displayed in the FL manager. Errors are displayed when they occur. (Refer to 16 page.)Displaying the protection history modeSTATUSMENUDisplaying the protection history(Refer to 18 page.)Initialization mode(Remove settings for Installer Setup.)STANDARDDSP SIMULATIONBackup data initialization is carried out.(Remove settings for Installer Setup.)Initialization mode(Includes settings for Installer Setup)CURSOR UPCURSOR DOWNBackup data initialization is carried out.(Includes settings for Installer Setup)Mode for switching tuner frequency stepSTANDARDDIRECT/STEREO-E2 model only-Change tuner frequency step to FM:200kHz/AM:10kHzSTEP.Mode for preventing remote control acceptanceSTATUSENTEROperations using remote control are rejected.(Mode cancellation: Turn off power and execute the same button operations as when performing setup.)Panel lock modeDSP SIMULATIONZONE2 Operations using main unit panel buttons or master volume are rejected.Panel lock mode(Remove Master volume)DIRECT/STEREOZONE2Operations using main unit panel buttons are rejected.Cancellation of panel lock modePURE DIRECTZONE2 Panel lock mode is cancelled.Installer Setup modeMENUCURSOR LEFTAccess Remote Maintenance mode via the internet.Installer Setup is displayed on GUI/Option Menu.Refer to AVR_RemoteMaintenance_.pdf of SDI.ON/OFFRETURNZONE2DSP SIMULATIONSTANDARDSTATUSENTERPUREDIRECTDIRECT/STEREOMENUCURSORf17AVR-3310CI/AVR-3310/AVR990/AVC-33101. Version display (com/DSP Error Display)1.1. Operation Speccom version display mode:When the following conditions are satisfied at its starting state, error informati