Denon-AVC2809-avr-sm维修电路原理图.pdf

Denon Brand Company, D&M Holdings lnc.For purposes of improvement, specifications and design are subject to change without notice.Please use this service manual with referring to the operating instructions without fail.Some illustrations using in this service manual are slightly different from the actual set.注意前、必読。本機、火災、感電、対安全性確保、配慮、法的電気用品安全法、所定許可得製造。従際、安全性維持、記載注意事項必守。本機仕様性能改良、予告変更。補修用性能部品保有期間、製造打切後 8 年。修理際、必取扱説明書参照上、作業行。本文中使用、説明都合上現物多少異場合。X0391 V.02 DE/CDM 0809SERVICE MANUALAV SURROUND RECEIVERAV SURROUND AMPLIFIERMODELJPEUECE2EKE2AE1CEUTAVR-2809CI?AVR-2809? ?AVR-989? ?AVC-2809?Ver. 2Please refer to theMODIFICATION NOTICE.RadioFans.CN 收音机爱 好者资料库2AVR-2809CI / AVR-2809 / AVR-989 / AVC-2809Please heed the points listed below during servicing and inspection. Heed the cautions!Spots requiring particular attention when servicing, suchas the cabinet, parts, chassis, etc., have cautions indicatedon labels or seals. Be sure to heed these cautions and thecautions indicated in the handling instructions. Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching in-ternal metal parts when the set is energized couldcause electric shock. Take care to avoid electric shock,by for example using an isolating transformer andgloves when servicing while the set is energized, un-plugging the power cord when replacing parts, etc.(2)There are high voltage parts inside. Handle with extracare when the set is energized. Caution concerning disassembly andassembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if fingers aremoved across them. Use gloves to protect your hands. Only use designated parts!The sets parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In par-ticular, for the important safety parts that are marked z onwiring diagrams and parts lists, be sure to use the desig-nated parts. Be sure to mount parts and arrange thewires as they were originally!For safety reasons, some parts use tape, tubes or other in-sulating materials, and some parts are mounted away fromthe surface of printed circuit boards. Care is also taken withthe positions of the wires inside and clamps are used tokeep wires away from heating and high voltage parts, sobe sure to set everything back as it was originally. Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected for servicing have been put back in their original po-sitions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insu-lation check on the external metal connectors and betweenthe blades of the power plug, and otherwise check thatsafety is ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnectthe antenna, plugs, etc., and turn the power switch on. Us-ing a 500V insulation resistance tester, check that the in-sulation resistance between the terminals of the powerplug and the externally exposed metal parts (antenna ter-minal, headphones terminal, microphone terminal, inputterminal, etc.) is 1M or greater. If it is less, the set mustbe inspected and repaired.Concerning important safetypartsMany of the electric and structural parts used in the sethave special safety properties. In most cases these prop-erties are difficult to distinguish by sight, and using re-placement parts with higher ratings (rated power andwithstand voltage) does not necessarily guarantee thatsafety performance will be preserved. Parts with safetyproperties are indicated as shown below on the wiring dia-grams and parts lists is this service manual. Be sure to re-place them with parts with the designated part number.(1) Schematic diagrams . Indicated by the z mark.(2) Parts lists . Indicated by the z mark.Using parts other than the designatedparts could result in electric shock, fires orother dangerous situations.SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of thepower cord is less than 460 kohms, the unit is defective.CAUTIONCAUTIONRadioFans.CN 收音机爱 好者资料库3AVR-2809CI / AVR-2809 / AVR-989 / AVC-2809、点検時注意願。注意事項守！特注意必要個所、 部品、 捺印注意事項表示。 注意書取扱説明書注意事項必守。感電注意！(1) 、交流電圧印加通電時内部金属部触感電。従通電時、絶縁使用手袋着用、部品交換、電源抜感電注意。(2) 内部高電圧部分、通電時取扱十分注意。分解、組立作業時注意！板金部品端面、部品製造時充分管理、 板金端面鋭利箇所有、 部品端面触指動怪我場合十分注意作業下。 手保護手袋着用。指定部品使用！部品難燃性耐電圧安全上特性持。 従交換部品、 使用同特性部品使用。特配線図、 部品表 z 印指定安全上重要部品必指定使用。部品取付配線引、 元！安全上、絶縁材料使用、基板浮取付部品。 内部配線引発熱部品高圧部品接近配慮、 必元。後安全点検！取外、 部品、 配線元、 個所周辺劣化点検、 外部金属端子部、 電源刃間絶縁、安全性確保確認。（絶縁方法）電源電源抜、 外、電源入。500V 絶縁抵抗計用、 電源端子外部露出金属部端子、端子、端子、入力端子間、絶縁抵抗値 M 以上確認。 値以下点検修理必要。安全上重要部品本機使用多電気部品、 機構部品安全上、 特別特性持。 特性場合、 外観判別、 部品高定格（定格電力、耐圧）持使用安全性維持、 限。 安全上特性持部品、 配線図、 部品表表示必指定部品番号使用願。(1) 配線図 z 表示。(2) 部品表 z 表示。指定部品異使用場合、感電、火災危険生恐。注意注意4AVR-2809CI / AVR-2809 / AVR-989 / AVC-2809DIMENSION AVR-2809CI / AVR-2809 / AVR-989 / AVC-2809 34443415515.5170.520.7244.5372.820.541454.75AVR-2809CI / AVR-2809 / AVR-989 / AVC-2809WIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly asthey were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noisegeneration.Wire arrangement viewed from the topEU modelBack Panel sideEC, E2, E1C, JP modelBack Panel side整形図調整部品交換等、類結束移動場合、作業完了時点整形。正整形発生原因。上面整形Front Panel sideFront Panel side6AVR-2809CI / AVR-2809 / AVR-989 / AVC-2809CAUTION IN SERVICINGInitializing AV SURROUND RECEIVER/AM-PLIFIERAV SURROUND RECEIVER/AMPLIFIER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced.1. Switch off the unit.2. Hold the following STANDARD button and DSP SIMULA-TION button, and switch on the unit.3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 but-tons and the microprocessor will be initialized.Note:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode.So make sure to memorize your setting for restor-ing after the initialization.JIG to use for servicingWhen you repair the printing board, you can use the following JIG. Please order to Denon Official Service Distributor in your region if necessary.Extention cable kit00D SPK- 561 EXTENSION UNIT KIT : 1 Set00D SPK- 562 TUCP CONN. JOINT KIT : 1 SetExtention cable for Idling CurrentParts Number for Extension Cables and Quantity of Unit. How to use and Adjust Idle Current.1. The thin and hard plate (ex. Ruler) is fixed with the tape behind the cable. 2. The voltmeter is connected with the other side of the ex-tension cable.3. Refer to ADJUSTMENT(Idling Current).Parts NumberParts NameQty / unitRemarks612050082004D6P 250mm NH1L=250mm 6P NH Cable612050083007D8P 250mm NH1L=250mm 8P NH Cable1,22,3時注意事項AV / 初期化周辺部品、Digital 基板等交換場合、AV / 初期化行下。1.on/off OFF 。2.STANDARD DSP SIMULATION 同時押、on/off 押 ON 。3.表示約 1 秒間隔点滅確認後、2 指離。初期化。注意 :上記 3 状態場合、一度操作 1直。初期化行客様設定内容工場出荷状態戻、設定内容控初期化後再設定。時使用治具基板修理際、使用治具下記。必要応販社注文下。延長00D SPK- 561 EXTENSION UNIT KIT : 1 式00D SPK- 562 TUCP CONN. JOINT KIT : 1 式電流用延長延長品番使用本数使用方法調整方法1.沿定規硬板止。2.反対側電圧計接続。3.調整項目参照電流調整。Parts NumberParts NameQty / unitRemarks612050082004D6P 250mm NH1L=250mm 6P NH Cable612050083007D8P 250mm NH1L=250mm 8P NH Cable7AVR-2809CI/AVR-989/AVR-2809/AVC-2809DISASSEMBLY Disassemble in order of the arrow of the figure of following flow.下記図矢印順番。 In the case of the re-assembling, assemble it in order of the reverse of the following flow.再組立場合、下記逆順番組立 In the case of the re-assembling, observe attention of assembling it.再組立場合、 組立注意遵守。TOP COVER SUB ASSYFRONT UNIT ASSYDIGITAL UNIT ASSYRefer to DISASSEMBLY 1.FRONT UNIT ASSYRefer to DISASSEMBLY 2.DIGITAL UNIT ASSYand EXPLODED VIEWand EXPLODED VIEWFLD UNITDIGITAL UNIT ASSY (Ref. No. of EXPLODED VIEW : 3-1) (Ref. No. of EXPLODED VIEW : 1)FUNC UNIT (Ref. No. of EXPLODED VIEW : 3-2)BACK PANEL ASSYFRONT IN UNITRefer to DISASSEMBLY 3.BACK PANEL ASSY (Ref. No. of EXPLODED VIEW : 3-3)and EXPLODED VIEWMIC UNITDIGITAL I/O UNIT (Ref. No. of EXPLODED VIEW : 3-4) (Ref. No. of EXPLODED VIEW : 3-6)P.SW UNIT (Ref. No. of EXPLODED VIEW : 3-9)A.VIDEO UNIT ASSYRefer to DISASSEMBLY 4.A.VIDEO UNIT ASSYand EXPLODED VIEWA.VIDEO UNIT (Ref. No. of EXPLODED VIEW : 2-1)TRANSAUDIO UNIT ASSYRefer to DISASSEMBLY 14.TRANSRefer to DISASSEMBLY 5.AUDIO UNIT ASSYand EXPLODED VIEWand EXPLODED VIEWTRANSAUDIO UNIT (Ref. No. of EXPLODED VIEW : 42) (Ref. No. of EXPLODED VIEW : 2-2)ZONE UNIT (Ref. No. of EXPLODED VIEW : 2-3)UCON CONNECT UNITRefer to DISASSEMBLY 6.UCON CONNECT UNITand EXPLODED VIEWUCON CONNECT UNIT (Ref. No. of EXPLODED VIEW : 3-8)AUDIO LIMIT UNITAM FM TUNERRefer to DISASSEMBLY 8.AUDIO LIMIT UNITREMOTE IPOD UNITand EXPLODED VIEWRefer to DISASSEMBLY 7.AM FM TUNER /AUDIO LIMIT UNITREMOTE IPOD UNIT (Ref. No. of EXPLODED VIEW : 4-7)and EXPLODED VIEWAM FM TUNER (Ref. No. of EXPLODED VIEW : 44)REMOTE IPOD UNIT (Ref. No. of EXPLODED VIEW : 3-5)MAIN CPU UNIT ASSYRefer to DISASSEMBLY 9.MAIN CPU UNIT ASSYand EXPLODED VIEWMAIN CPU UNIT (Ref. No. of EXPLODED VIEW : 6-1)PRIM/CPU SUPPLY UNIT ASSYREG UNIT ASSYRefer to DISASSEMBLY 13.PRIM/CPU SUPPLY ASSYRefer to DISASSEMBLY 10.REG UNIT ASSYand EXPLODED VIEWand EXPLODED VIEWPOWER UNITREG UNIT (Ref. No. of EXPLODED VIEW : 6-2) (Ref. No. of EXPLODED VIEW : 4-1)PRIM/CPU SUPPLY UNIT (Ref. No. of EXPLODED VIEW : 6-3)PRE AMP UNIT ASSYUCON JUNCTION UNITRefer to DISASSEMBLY 11. PRE AMP UNIT ASSY (Ref. No. of EXPLODED VIEW : 6-4)and EXPLODED VIEWPRE AMP UNIT (Ref. No. of EXPLODED VIEW : 4-6)POWER AMP UNIT ASSYRefer to DISASSEMBLY 12.POWER AMP UNIT ASSYand EXPLODED VIEWREG UNIT (Ref. No. of EXPLODED VIEW : 5-1)8AVR-2809CI/AVR-989/AVR-2809/AVC-2809EU modelPicture BPicture APicture CPicture DPicture EThe viewpoint of each photograph(photography direction)各図視点(撮影方向)Top viewFront sideEC, E2, E1C, JP modelPicture BPicture APicture CPicture DPicture EThe viewpoint of each photograph(photography direction)各図視点(撮影方向)Top view9AVR-2809CI/AVR-989/AVR-2809/AVC-28091. FRONT UNIT ASSY(1) Disconnect the connector wires. ( 。 ） Proceeding ( 手順 ) : TOP COVER SUB ASSY FRONT UNIT ASSY CX062Top viewcutCX021EU modelCX062Top viewcutCX021EC, E2, E1C, JP model10AVR-2809CI/AVR-989/AVR-2809/AVC-2809(2) Disconnect the FFC cable.（FFC 。 ） (3) Remove the screws. ( 。 ）CORD HOLDER : LooseFFC CABLEPicture CTop viewBottom viewPlease refer to EXPLODED VIEW for the disassembly method of each P.W.B included in FRONT UNIT ASSY.FRONT UNIT ASSY 各基板 EXPLODED VIEW 参照。11AVR-2809CI/AVR-989/AVR-2809/AVC-28092. DIGITAL UNIT ASSY (1) Disconnect the connector wires and boards.（。 ） (2) Remove the screws. ( 。) Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY DIGITAL UNITDIGITAL I/O UNITCX041CX131CX065CX035Top viewcutCORD HOLDER : LooseBoard to boardEU modelDIGITAL UNITDIGITAL I/O UNITCX041CX131CX065CX035Top viewcutCORD HOLDER : LooseBoard to boardEC, E2, E1C, JP modelPicture BEU modelPicture BEC, E2, E1C, JP model12AVR-2809CI/AVR-989/AVR-2809/AVC-28093. BACK PANEL ASSY(1) Remove the screw cover.（SCREW COVER 。 ） (2) Remove the screws.（。 ） Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY SCREW COVERPUSH RIVETPicture BEU modelPicture BPUSH RIVETSCREW COVEREC, E2, E1C, JP modelPicture B?EU modelPicture B?EC, E2, E1C, JP modelPlease refer to EXPLODED VIEW for the disassembly method of each P.W.B included in BACK PANEL ASSY.BACK PANEL ASSY 各基板 EXPLODED VIEW 参照。13AVR-2809CI/AVR-989/AVR-2809/AVC-28094. A.VIDEO UNIT ASSY(1) Disconnect the connector wires and boards. ( 。 ） 5. AUDIO UNIT ASSY(1) Disconnect the connector wires and boards. ( 。)Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY A.VIDEO UNITBoard to boardCX077Top viewCY085Board to boardEU modelBoard to boardCX077Board to boardTop viewA.VIDEO UNITEC, E2, E1C, JP modelProceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY AUDIO UNITBoard to boardCY135CY079Board to boardTop viewEU model14AVR-2809CI/AVR-989/AVR-2809/AVC-28096. UCON CONNECT UNIT(1) Disconnect the connector board.（。 ）AUDIO UNITBoard to boardCY135CY079Board to boardTop viewEC, E2, E1C, JP modelProceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY UCON CONNECT UNIT Picture BCX125CX12415AVR-2809CI/AVR-989/AVR-2809/AVC-28097. AM FM TUNER / REMOTE IPOD UNIT(1) Disconnect the connector wire and connector board.（FFC 。 ）8. AUDIO LIMIT UNIT(1) Disconnect the connector boards.（。 ） Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY UCON CONNECT UNIT AM FM TUNER / REMOTE IPOD UNIT FFC CABLEPicture BBoard to boardAM FM TUNERREMOTE IPOD UNITProceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY UCON CONNECT UNIT AUDIO LIMIT UNIT Top viewBoard to board16AVR-2809CI/AVR-989/AVR-2809/AVC-28099. MAIN CPU UNIT ASSY (1) Disconnect the connector wire and FFC cables. ( FFC 。)(2) Remove the screw.（。 ）Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY UCON CONNECT UNIT AUDIO LIMIT UNIT MAIN CPU UNIT ASSY CX115Picture EPCB HOLDERFFC CABLEMAIN CPU UNITEU modelCX115Picture EPCB HOLDERFFC CABLEMAIN CPU UNITEC, E2, E1C, JP modelPicture CMAIN CPU UNIT17AVR-2809CI/AVR-989/AVR-2809/AVC-280910. REG UNIT ASSY(1) Disconnect the connector wire and remove the screws. （。)Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY UCON CONNECT UNIT AUDIO LIMIT UNIT MAIN CPU UNIT ASSY REG UNIT ASSY CX031Wire clamp band : LooseBoard to boardPicture BEU modelCX031Wire clamp band : LooseBoard to boardPicture BEC, E2, E1C, JP model18AVR-2809CI/AVR-989/AVR-2809/AVC-280911. PRE AMP UNIT ASSY(1) Remove the screws and disconnect the connector board.（。 ）Proceeding ( 手順 ) : TOP COVER SUB ASSY DIGITAL UNIT ASSY BACK PANEL ASSY A.VIDEO UNIT ASSY AUDIO UNIT ASSY UCON CONNECT UNIT AUDIO LIMIT UNIT MAIN CPU UNIT ASSY REG UNIT ASSY PRE AMP UNIT ASSY Top viewBoard to boardEU modelTop viewBoard to boardEC, E2, E1C, JP model19AVR-2809CI/AVR-989/AVR-2809/AVC-280912. POWER AMP UNIT ASSYb When repairing, be sure to provide spatial distance between R752 to R765 and C723 to C729.R752 to R765 become hot when there is a problem.As a measure to deal with the heat of R752 to R765, attach GLASS TUBE to C723 to C729 for products with serial num-bers starting from the ones indicated below.Do not attach GLASS TUBE to products with earlier seria