SONY MZ-NF610电路原理图 .pdf
SERVICE MANUAL PORTABLE MINIDISC RECORDER US Model Canadian Model SPECIFICATIONS MZ-NF610 US and foreign patents licensed from Dolby Laboratories. Continued on next page Model Name Using Similar MechanismMZ-R410 Mechanism TypeMT-MZN710-177 Optical Pick-up NameLCX-5R Ver 1.0 2003. 03 9-877-144-01Sony Corporation 2003C167800-1Personal Audio Company C 2003.03Published by Sony Engineering Corporation SonicStage, OpenMG and the OpenMG logo, MagicGate, Net MD and the Net MD logo are trademarks of Sony Corporation. Microsoft, Windows, Windows NT and Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United States and /or other countries. IBM and PC/AT are registered trademarks of International Business Machines Corporation. Macintosh is a trademark of Apple Computer, Inc. in the United States and/ or other countries. MMX and Pentium are trademarks or registered trademarks of Intel Corporation. All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders. and marks are omitted in this manual. MD recorder Audio playing system MiniDisc digital audio system Laser diode properties Material: GaAlAs Wavelength: = 790 nm Emission duration: continuous Laser output: less than 44.6 W (This output is the value measured at a distance of 200 mm from the lens surface on the optical pick-up block with 7 mm aperture.) Recording and playback time (when using MDW-80) Maximum 160 min. in monaural Maximum 320 min. in LP4 stereo Revolutions 380 rpm to 2,700 rpm (CLV) Error correction ACIRC (Advanced Cross Interleave Reed Solomon Code) Sampling frequency 44.1 kHz Sampling rate converter Input: 32 kHz/44.1 kHz/48 kHz Coding ATRAC (Adaptive TRansform Acoustic Coding) ATRAC3 LP2/LP4 本资料由O K X I A 视听皮带资源库w w w . o k x i a . c n 提供 本资料由视听皮带资源库 收集整理提供 2 MZ-NF610 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUM- BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY. Modulation system EFM (Eight to Fourteen Modulation) Frequency response 20 to 20,000 Hz 3 dB Inputs1) Line in: stereo mini-jack for analog input (minimum input level 49 mV) optical (digital) mini-jack for optical (digital) input Outputs i: stereo mini-jack Maximum output level USA model: 5mW + 5mW; load impedance 24 Canadian model: 5mW + 5mW; load impedance 16 Radio Frequency range USA model: FM: 87.5-108 MHz AM: 530-1,710 kHz (10 kHz step) 531-1,710 kHz (9 kHz step) TV: 2-13 CH WEATHER: 1-7 CH Canadian model: FM: 87.5-108 MHz AM: 530-1,710 kHz (10 kHz step) 531-1,710 kHz (9 kHz step) Antenna FM/TV/WEATHER: Headphones/earphones cord antenna AM: Built-in ferrite bar antenna General Power requirements Sony AC Power Adaptor connected at the DC IN 3V jack: 120 V AC, 60 Hz (Models for USA, Canada, Mexico, and Taiwan) 230 V AC, 50/60 Hz (Models for continental Europe and Chili) 240 V AC, 50 Hz (Model for Australia) 220 V AC, 50 Hz (Model for China) 230 V AC, 50 Hz (Models for U.K. and Hong Kong) 220 V AC, 60 Hz (Model for Korea) 100 - 120 V/220 - 240 V AC, 50/60 Hz (Other models) The recorder: Nickel metal hydride rechargeable battery NH-7WMAA 1.2V 700 mAh (MIN) Ni-MH LR6 (size AA) alkaline battery Dimensions Approx. 81.0 27.7 74.4 mm (w/h/d) (31/4 11/8 3 in.) Mass Supplied accessories Approx. 103 g (3.6 oz) the recorder only 1)The LINE IN (OPTICAL) jack is used to connect either a digital (optical) cable or a line (analog) cable. 2)The i jack connects either headphones/ earphones or a line cable. 3)Measured in accordance with JEITA. US and foreign patents licensed from Dolby Laboratories. Design and specifications are subject to change without notice. AC power adaptor (1) Headphones with a remote control (1) (for USA model) NH-7WMAA Nickel metal hydride rechargeable battery (1) Dedicated USB cable (1) Earphones with a remote control (1) (for Canadian model) Battery carrying case (1) CD-ROM (SonicStage Ver. 1.5) (1)* Do not play a CD-ROM on an audio CD player. Battery life The battery life may be shorter due to operating conditions, the temperature of the location, or alkaline dry battery you use. When recording (Unit: approx.hours)(JEITA1) 1)Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries Association) standard. BatteriesSP Stereo LP2 Stereo LP4 Stereo Nickel metal hydride rechargeable battery2) 2)When using a 100% fully charged nickel metal hydride rechargeable battery (NH-7WMAA). 5.589 LR6 Sony alkaline dry battery3) 3)When using a Sony LR6 (SG) “STAMINA” alkaline dry battery (produced in Japan). 91216 When using the radio (Unit: approx.hours)(JEITA) Note When you use the radio, it is recommended that you use a fully charged rechargeable battery or a new dry battery since more power is consumed by the radio than by MD playback. When playing (Unit: approx.hours)(JEITA) BatteriesSP Stereo LP2 Stereo LP4 Stereo Nickel metal hydride rechargeable battery 14.515.517.5 LR6 Sony alkaline dry battery 3642.548 BatteriesFM/ AM TV/Wb (weather) (USA model only) Nickel metal hydride rechargeable battery 7.57 LR6 Sony alkaline dry battery 18.517 本资料由视听皮带资源库 收集整理提供 3 MZ-NF610 On power sources Use house current, nickel metal hydride rechargeable battery, LR6 (size AA) battery, or car battery. For use in your house: Do not use any other AC power adaptor since it may cause the recorder to malfunction. Connect the AC power adaptor to an easily accessible AC outlet. Should you notice an abnormality in the AC power adaptor, disconnect it from the AC outlet immediately. The recorder is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the recorder itself has been turned off. If you are not going to use this recorder for a long time, be sure to disconnect the power supply (AC power adaptor, dry battery, rechargeable battery, or car battery cord). To remove the AC power adaptor from the wall outlet, grasp the adaptor plug itself; never pull the cord. Polarity of the plug TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL.5 3.DISASSEMBLY 3-1.Disassembly Flow .6 3-2.Case (Lower) .7 3-3.Upper Panel Section.7 3-4.LCD Module, Button (Control) .8 3-5.MAIN Board .8 3-6.Mechanism Deck (MT-MZN710-177) .9 3-7.Set Chassis Assy .9 3-8.OP Service Assy (LCX-5R). 10 3-9.Holder Assy . 11 3-10. DC Motor (Sled) (M602). 11 3-11. DC Motor (Over Write Head Up/Down) (M603), DC SSM18B Motor (Spindle) (M601). 12 4.TEST MODE. 13 5.ELECTRICAL ADJUSTMENTS. 19 6.DIAGRAMS 6-1.Block Diagram . 39 6-2.Note for Printed Wiring Board and Schematic Diagrams . 40 6-3.Printed Wiring Board MAIN Board (Side A) . 41 6-4.Printed Wiring Board MAIN Board (Side B) . 42 6-5.Schematic Diagram MAIN Board (1/4) . 43 6-6.Schematic Diagram MAIN Board (2/4) . 44 6-7.Schematic Diagram MAIN Board (3/4) . 45 6-8.Schematic Diagram MAIN Board (4/4) . 46 6-9.IC Pin Function Description . 52 7.EXPLODED VIEWS 7-1.Case Section . 58 7-2.Chassis Section . 59 7-3.MAIN Board Section . 60 7-4.Mechanism Deck Section-1 (MT-MZN710-177). 61 7-5.Mechanism Deck Section-2 (MT-MZN710-177). 62 8.ELECTRICAL PARTS LIST. 63 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur- ing repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C . Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 本资料由视听皮带资源库 收集整理提供 4 MZ-NF610 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK Never look into the laser diode emission from right above when checking it for adjustment. It is feared that you will lose your sight. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK (LCX-5R) The laser diode in the optical pick-up block may suffer electro- static break-down easily. When handling it, perform soldering bridge to the laser-tap on the flexible board. Also perform mea- sures against electrostatic break-down sufficiently before the op- eration. The flexible board is easily damaged and should be handled with care. OPTICAL PICK-UP FLEXIBLE BOARD SECTION 1 SERVICING NOTES laser-tap In performing the repair with the power supplied to the set, re- moving the MAIN board causes the set to be disabled. In such a case, make a solder bridge to short SL802 (OPEN/ CLOSE) on the MAIN board. Handle the FLEXIBLE board (over write head) with care, as it has been soldered directly to the MAIN board. In repairing the component side of MAIN board, connect the FLEXIBLE board (over write head) and the MAIN board with the lead wires in advance. System requirements The following hardware and software are required in order to use the SonicStage software for the Net MD. This software is not supported by the following environments: Macintosh Windows XP versions other than Home Edition or Professional Windows 2000 versions other than Professional Windows 98 versions other than Second Edition Windows NT Windows 95 Personally constructed PCs or operating systems An environment that is an upgrade of the original manufacturer-installed operating system Multi-boot environment Multi-monitor environment Notes We do not ensure trouble-free operation on all computers that satisfy the system requirements. We do not ensure trouble-free operation of the system suspend, sleep, or hibernation function on all computers. ComputerIBM PC/AT or Compatible CPU: Pentium II 400 MHz or higher (Pentium III 450 MHz or higher is recommended.) Hard disk drive space1): 120 MB or more RAM: 64 MB or higher (128 MB or higher is recommended) 1) Others CD-ROM drive (capable of digital playback by WDM) Sound Board USB port (supports USB 2.0 Full Speed (previously USB 1.1) Operating System Factory installed: Windows XP Home Edition/Windows XP Professional/Windows Millennium Edition/Windows 2000 Professional/Windows 98 Second Edition DisplayHigh Color (16bit) or greater, 800 480 dots or more (800 600 dots or more is recommended) OthersInternet access: for Web registration and EMD services Windows Media Player (version 7.0 or higher) installed for playing WMA files Note on hard disk drive space 120 MB or more free space on the hard disk drive is required. If your computer does not have enough space, the software will not be properly installed. The required free space differs according to the version of your Windows OS, or the amount of audio files that you handle. This set requires the patch data in the nonvolatile memory (IC851) to be rewritten using the application, when the MAIN board was replaced. (See page 31) upper panel assy MAIN board FLEXIBLE board (over write head) IC801 IC501 * R836 TP1836 TP18 TP1845 TP1837 TP1835 SL502 TP824 TP1528 TP1834 TP1830 TP1831 TP1868 TP1511 TP1510 TP1525 TP153 C825C826 R841 SL802 * CSP(Chip Size Package) CSP (Chip Size Package) SL802 (OPEN/CLOSE) MAIN Board (Side B) 本资料由视听皮带资源库 收集整理提供 5 MZ-NF610 SECTION 2 GENERAL This section is extracted from instruction manual. 14 Looking at controls The recorder A Display window B GROUP button C X (pause) button D END SEARCH button E MENU button F OPEN button G VOL +*, button *VOL + has a tactile dot. H 4-way control key ENTER N* ., (search/AMS) x CANCEL/CHG (stop/cancel/ charge) * N has a tactile dot. I REC (record) T MARK button J USB connecting jack K Handstrap hole Use the hole to attach your own strap. L Battery compartment (at the bottom) M LINE IN (OPTICAL) jack N HOLD switch To prevent the buttons from being acci
