GrundigSonoclock51SC5301 维修电路图、原理图.pdf
-
资源ID:110020
资源大小:1.62MB
全文页数:9页
- 资源格式: PDF
下载积分:18积分
会员登录下载
三方登录下载:
友情提示
2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
|
GrundigSonoclock51SC5301 维修电路图、原理图.pdf
Sonoclock 51 SC 5301 Service Document Exchange Set Es gelten die Vorschriften und Sicherheitshinweise gem dem Service Manual Sicherheit, Material- nummer 720108000000, sowie zustzlich die even- tuell abweichenden, landesspezifischen Vorschrif- ten! The regulations and safety instructions shall be valid as provided by the Safety Service Manual, part number 720108000000, as well as the respective national deviations. S Dieses Service Dokument ist nur in Datenform verfgbar This Service Document is only available as data nderungen vorbehalten/Subject to alteration Made by GRUNDIG in Germany H-S43 0303 S Service Manual Sicherheit Safety Materialnr./Part No. 720108000000 ? Sonoclock 51 SC 5301? Sonoclock 51 SC 5301? Sonoclock 51 SC 5301? Sonoclock 51 SC 5301? Sonoclock 51 SC 5301? Sonoclock 51 SC 5301? Sonoclock 51 SC 5301? EQUIPMENT REQUIRED Signal Source 1.MW/LW signal generator (AM SG) 2. FM signal generator (FM SG) 3. Sweep generator (10.7 Mhz for FM) Output Indicator 1. SSVM 2. Oscilloscope 3. Frequency Counter General preparation 1. Check source voltage. 2. Set function switch to band being aligned 3. Turn volume control to minimum (unless noted otherwise) 4. Connect low side of signal and output indicator to chassis ground unless otherwise specified. Keep ground connection close to high side connection. 5. Keep signal inout as low as possible to avoid AGC and AFC action (set output indicator to high sensitivity.) 6. Standard modulation is 1000 Hz AT 30% amplitude for MW/LW (1000 Hz at 22.5 kHz deviation for FM) AM IF ALIGNMENT Step Signal source (AM RF Gen) Connect to Set signal to Aligment indicator connect to Oscilloscope or SSVM Set radio dial to AdjustAdjust for Remarks 1A standard radiation loop460 KHzT4 Detector Output TerminalQuiet pointT3Maximum Volume control min position 2Repeat for maximum output MW RF ALIGNMENT Signal source (AM Signal Gen.) connect to Set signal to Alignment indicator Connect toSet radio dial to Adjust Adjust forRemarks 1 515 KHz (modulated) 515 KHz (lowest end) T1 (Osc, coil) 2 1640 KHz (modulated) 1640 KHz (Highest end) TC4 (Osc, trim) 3 600 KHz (modulated) 600 KHzL2 (ant coil) 4 1440 KHz (modulated) 1440KHzTC3 (ant trim) 5Repeat Steps 3 and 4 as necessary to minimize tracking error. Also repeat steps 1 and 2 if necessary. LW RF ALIGNMENT Signal source (AM Signal Gen.) connect to Set signal to Alignment indicator Connect toSet radio dial to Adjust Adjust forRemarks 1 140 KHz (modulated) 140 KHz (lowest end) T2 (Osc, coil) 2 290 KHz (modulated) 290 KHz (Highest end) TC6 (Osc, trim) 3 153 KHz (modulated) 153 KHzL3(ant coil) 4 261 KHz (modulated) 261 KHzTC5 (ant trim) 5Repeat Steps 3 and 4 as necessary to minimize tracking error. Also repeat steps 1 and 2 if necessary. FM RF ALIGNMENT Step Signal source (FM Signal Gen.) Connect to Set signal to Alignment indicator (oscilloscope , VTVM Connect to Set radio dial to AdjustAdjust for Remarks 1 87.35 MHz modulated 87.35MHz (lowest end) L1 (Osc, coil) 2 108.25 MHz modulated 108.25MHz (Highest end) TC2 (Osc, trimmer) 3 90 MHz modulated 90MHz L2 (RF coil) stretch or squeeze 4 106 MHz modulated 106MHzTC1 (RF trim) 5repeat steps 3 and 4 as necessary to minimum tracking error. Also repeat steps 1 and 2 if necessary. * UK models must not be able to tune below 87.5 MHz. Across speaker voice coilMaximum Volume control max- position TP 1, GND (Test point) through matching network if necessary Across speaker voice coilMaximum Volume control Max- position A standard radiation loop antenna ALIGNMENT PROCEDURE MODEL NO. GRUNDIG SONOCLOCK SC 51 A standard radiation loop antennaAcross speaker voice coilMaximum Volume control max- position Sonoclock 51 SC 5301? 18 33 10 28 6 13 32 14 23 37 11 22 9 12 27 15 26 7 24525212036142 35 17 31 8 3 34 16 29 30