Teac-AD600-cd-sm维修电路原理图.pdf

A AD D- -6 60 00 0 SERVICE MANUAL Compact Disc Multi Player/Reverse Cassette Deck Effective : November, 2000S-0032A CONTENTS 1 SAFETY INFORMATION 2 2 SPECIFICATIONS 3 3 ADJUSTMENTS AND CHECKS 4 4 EXPLODED VIEWS AND PARTS LIST 10 5 PC BOARDS AND PARTS LIST 16 6 INCLUDED ACCESSORIES 21 目 次 1 SAFETY INFORMATION 2 2 仕 様 3 3 調整確認 4 4 分解図 10 5 基板図 16 6 付属品 21 NOTES PC boards shown are viewed from parts side. Parts marked with * require longer delivery time. The parts with no reference number or no parts number in the exploded views are not supplied. As regards the resistors and capacitors, refer to the circuit diagrams contained in this manual. Parts marked with this sign are safety critical components. They must be replaced with identical components - refer to the appropriate parts list and ensure exact replacement. Parts of mark can be used only with the version designated. J:JAPAN US:U.S.A. C:CANADA GE:GENERAL EXPORT K:KOREA E:EUROPE UK:U.K. A:AUSTRALIA 注意 基板図部品面示。 *印部品納期若干。 了承。 分解図部番部品品番部品供給 。 標準抵抗、省略。 回路図参照。 印安全重要部品。 交換時必指定部品使用。 仕向先 J:JAPAN US:U.S.A. C:CANADA GE:GENERAL EXPORT K:KOREA E:EUROPE UK:U.K. A:AUSTRALIA RadioFans.CN 收音机爱 好者资料库 1 SAFETY INFORMATION 2 This product has been designed and manufactured according to FDA regulations title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968, and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings. The label required in this regulation is shown 1. OCAUTION USE OF CONTROLS OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CD 1For U.S.A. Optical pickup: Type: LTOH96MK or GH5C105A1APK Manufacturer : SHARP Corporation Laser output : Less than 0.5 mW on the objective lens Wavelength: 770-795 nm Voltage Conversion (General export models only) Be sure to remove the power cord from the AC outlet before repositioning the voltage converter switch. 1. Locate the voltage selector on the rear panel. 2. Using a flat-bladed screwdriver, set to the appropriate 230V or 120V position according to your area. RadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONS 3 仕様 CD部 数.2 周波数特性 .1020,000Hz 1dB SN比 .90dB 高調波歪率 .0.02% (1kHz) .測定限界値以下 （水晶発振精度） .70dB .約12 出力 (RCA).2V . 8倍 部 方式.42 構成 .録音再生 x 1 （回転式） 消去x 1 速度.4,76cm/sec .約12 .DC x 1 .0.08% (W.RMS) 周波数特性 （総合） .6315,000Hz 3dB： 6314,000Hz 3dB： SN比 （総合） .57dB （NR, 3%THDWTD） 66dB （B NR, 5kHz以上） 早巻時間.約120秒 （C-60） 入力 (RCA).300mV （入力50k） 出力 (RCA).300mV （負荷50k） 出力 .5mW/33 一般 電源 .100V AC 50-60Hz 消費電力 .18W 外形寸法 .435 x 147 x 293mm (WxHxD) 質量 .5.5kg 付属品.RC-778 x 1個 x 2本 乾電池 (単3、SUM-3) x 2本 取扱説明書 保証書 仕様外観、改善予告変更 。 CD player section (Audio) Number of channels.2 Frequency response .10 - 20,000 Hz 1 dB Signal-to-noise ratio.90 dB Dynamic range .90 dB Total harmonic distortion .0.02% (1 kHz) Wow and flutter .Unmeasurable (quartz accuracy) Channel separation.70 dB Output .2 Vrms Digital filter .8-times oversampling digital filter (Signal format) Sampling frequency.44.1 kHz D/A converter .16-bit linear/channel Channel bit rate.4.3218 Mb/sec. Channel modulation code .EFM Error correction .CIRC Cassette section Track system.4-track 2-channel stereo Heads.Record/playback x 1 (rotary reverse) erase x 1 Type of tape .Cassette tape C-60, C-90 Tape speed .4.76 cm/sec. Motor .DC servo motor x 1 Wow and flutter .0.08% (W. RMS) Frequency response (overall) .63 - 15,000 Hz 3 dB, chrome 63 - 14,000 Hz 3 dB, normal Signal-to-noise ratio (overall) . 57 dB (Dolby NR off, 3% THD level, weighted) 66 dB (DOLBY NR on, over 5 kHz) Fast winding time.Approx. 120 sec. (with C-60) Input .Line; 300mV (input impedance of 50 kohms or more) Output.Line; 300mV (load impedance of 50 kohms or more) Headphones; 5mW/33 ohms General Power requirements .120/230 V AC, 50-60 Hz (U.S.A./Canada/general export model) 230 V AC, 50 Hz (Europe/U.K. model) Power consumption .18 W Dimensions (W x H x D) .435 x 147 x 293 mm (17-1/8 x 5-13/16 x 11-9/16) Weight.5.5 kg (12-5/8 lbs.) Standard Accessories .Wireless remote control RC-778 x 1 Pin plug cord x 2 Battery (SUM-3, AA, R6 type) x 2 Improvements may result in specification or feature changes without notice. Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. 実施権基製造 。 、DOLBY及D記号 登録商標。 3 ADJUSTMENTS AND CHECKS 4 調整確認 3-1 CD PLAYER SECTION 3-1-1 Pitch control adjustment 1. Connect the frequency counter to the CD OUT. 2. Turn on a CD PITCH CONTROL switch at the stop mode. 3. Play the track 2 (1kHz, 0dB) of the MCD-111. 4. Set a CD PITCH CONTROL knob to a center, and adjust R811 of CONTROL PCB so that the output becomes 1kHz. 5. When the CD PITCH CONTROL knob is rotated to the side, make sure the frequency becomes 880 Hz or lower, and make sure it becomes 1,120 Hz or higher when the knob is rotated to the side. 3-1-2 Output level check 1. Connect the AC voltmeter to the CD OUT. 2. Play the track 2 (1kHz, 0dB) of the MCD-111, and check the output level. Specification: 2.00.5Vrms 3-1-3 Distortion check 1. Connect the distortion meter to the CD OUT. 2. Play the track 2 (1kHz, 0dB) of the MCD-111, and check the distortion. Specification: 0.03% or less (400Hz HPF 22kHz LPF) 3-1-4 Frequency response check 1. Play the track 3-6 (20Hz 20kHz, 0dB) of the MCD-111, and check that output level are within the specified values with respect to the 1kHz reference level. Specification: within 1dB 3-1-5 S/N check 1. Play the track 7 (non-signal) of the MCD-111, and check that noise level are within the specified values with respect to the 1kHz reference level. Specification: 83dB or more (22kHz LPF IEC-A) 3-1-6 Channel separation check 1. Play the track 8 (L:1kHz / R:non-signal) of the MCD-111, and check the leakage from Lch to Rch. 2. In the same way, play the track 10 (R:1kHz / L:non-signal) of the MCD-111, and check the leakage from Rch to Lch. Specification: 70dB or more (22kHz LPF IEC-A) 3-1 CD部 3-1-1 調整 1. CD OUT端子周波数接続。 2. 停止状態CD PITCH CONTROLON。 3. MCD-1112曲目(1kHz, 0dB)再生。 4. CD PITCH CONTROL、出力 1kHz、CONTROL PCBR811調整。 5. CD PITCH CONTROL方向回、周波数 880Hz以下、方向回、1,120Hz以上 確認。 3-1-2 出力 1. CD OUT端子AC接続。 2. MCD-1112曲目(1kHz, 0dB)再生、出力確 認。 規格: 2.00.5Vrms 3-1-3 歪率 1. CD OUT端子歪率計接続。 2. MCD-1112曲目(1kHz, 0dB)再生、歪率確認。 規格: 0.03%以下（400Hz HPF 22kHz LPF） 3-1-4 周波数特性 1. MCD-11136曲目(20Hz20kHz, 0dB)再生、基 準(1kHz, 0dB)対規格内確認。 規格: 1dB以内 3-1-5 S/N 1. MCD-1117曲目(無信号)再生、基準 対規格内確認。 規格: 83dB以上（22kHz LPF IEC-A） 3-1-6 1. MCD-1118曲目(L:1kHz / R: 無信号)再生、Rch 漏確認。 2. 同様10曲目(R:1kHz / L: 無信号)再生、Lch漏 確認。 規格: 70dB以上（22kHz LPF IEC-A） 5 3-2 CASSETTE DECK SECTION Before performing adjustments and checks clean and demagnetize the entire tape path. In general, adjustments and checks are made in the order of Lch then Rch. Double REF. Nos. indicate Lch/Rch. (Example; R181/R182) 0dB is referenced to 0.775V. The AC voltmeter used in the procedures must have an input impedance of 1M or more. Unless specified otherwise, adjustments and checks are made in FWD direction. 3-2 部 調整確認前、走行系消磁清掃行 。 特指定限、調整Lch, Rch順序行 。尚、R181/R182記回路番号 Lch/Rch示。 0dB0.775V。 測定使用計入力1M以上 使用。 特指定場合、調整確認FWD方向行 。 Fig. 3-1 Adjustment locations TAPE PCB R291 R292 R293 R294 R030 R181 R182 L101L102 L004 BN105 21 Frequency Counter 6 3-2-1 Mechanical performance 機構系 ITEM 項目 SETTING 設定 ADJUSTMENTS 調整所 3. Pitch control variable range 可変幅 Check 1. Wow and flutter PITCH CONTROL: Center FWD and REV play Check 2. Tape speed 速度 PITCH CONTROL: Center FWD play CONTROL PCB R652 MEASURING POINTS, RESULT 測定所調整値 0.19% or less (WRMS) 3,00020Hz PITCH CONTROL : 2,640Hz or lower PITCH CONTROL : 3,360Hz or higher 3,00075HzCheckREV play Fig. 3-3 Oscillator Distortion Analyzer Oscilloscope AC voltmeter AD-600 1kHz Filter L S1 R L R LINE INLINE OUT S2 Fig. 3-2 Basic test setup TEST TAPE MTT-111N MTT-111N MTT-111N MTT-111N Frequency Counter Wow C 11 EXPLODED VIEW-1 REF.NO.PARTS NO.DESCRIPTION 1- 1 * 3M0026000DBONNET 1- 2 * 3M000880 BUSHING,#2271 1- 3 3E002120 POWER CORD J 3E009230 POWER CORD US,C,GE 3E006330 POWER CORD K 3E015210 POWER CORD E 3E000350 POWER CORD UK 3E000360 POWER CORD A 1- 4 * 3M0109600AREAR PANEL J * 3M0109610AREAR PANEL US,C,GE * 3M0109620AREAR PANEL K,E,UK,A 1- 5 * 3E9526000APCB ASSY,DO J 1- 6 3M0025900APLATE,IC 1- 7 3E010000 FER.CORE,B18T 25X12X15 1- 8 * 3E0139200BPOWER TRANSFORMER 1- 9 * 3E9526400APCB ASSY,TRANS(P) J * 3E9526413APCB ASSY,TRANS(P) US,C,GE * 3E9526437APCB ASSY,TRANS(P) K * 3E9526440APCB ASSY,TRANS(P) E,UK * 3E9526460APCB ASSY,TRANS(P) A 1-10 * 3E9526500APCB ASSY,TRANS(S) 1-11 * 3M0115500AINSUL COVER,A 1-12 * 3M0110100ABRACKET,POWER TRANS 1-13 * 3E9526200APCB ASSY,TAPE 1-14 * 3M0109700ABRACKET,PCB A 1-15 * 3M0109800ABRACKET,PCB B 1-16 * 3E9528400APCB ASSY,REG 1-17 * 3E0139000AFFC,BNCD-P=1.0-K-15-180 1-18 * 3E0138900AFFC,BNCD-P=1.25-K-12-320 1-19 * 3E0139100AFFC,SFBNCD-P=1.0-K-16-320 1-20 * 3E9525500APCB ASSY,CONTROL 1-21 * 3M0109900ABRACKET,PCB C 1-22 3M0030500BBUTTON,POWER 1-23 * 3M0108800AROD,POWER 1-24 * 3M0115600AINSUL COVER,B 1-25 * 3E9526600APCB ASSY,P.SW 1-26 * 3M0110200ABRACKET,POWER S/W 1-27 * 3M0109500ACHASSIS,BOTTOM 1-28 3M0108000ADOOR,CD1 1-29 3M0108010ADOOR,CD2 1-30 3M0108020ADOOR,CD3 1-31 3M0111400ACD MECHA ASSY,MGC-F3000 1-32 3M0047200AFOOT ASSY 1-33 * 3M0111500AMECH ASSY,CMAL2Z213A 1-34 * 3M0029900ABRACKET,EJECT A 1-35 3M0010600ATORSION SPRING,EJECT 1-36 * 3M0029800AHOOK,EJECT A 1-37 * 3M0108700AKNOB,EJECT 1-38 3M0011200ADAMPER 1-39 * 3E9525800APCB ASSY,FRONT(B) 1-40 * 3E9526700APCB ASSY,V SELECT US,C,GE 1-41 3M0108100AKNOB,MAIN 1-42 * 3E9525600APCB ASSY,FLD 1-43 * 3M0109000ALENS,PITCH CONTROL 1-44 3M0108400AKNOB,SKIP REF.NO.PARTS NO.DESCRIPTION 1-45 3M0108200AKNOB,DISC 1-46 3M0108300AKNOB,CD OPEN 1-47 * 3E9525900APCB ASSY,FRONT(C) 1-48 3M0108600AKNOB,VOLUME 1-49 * 3E9526300APCB ASSY,HP 1-50 * 3M0110000ABRACKET,PHONE 1-51 * 3E9525700APCB ASSY,FRONT(A) 1-52 * 3M0051600ATEAC EMBLEM(GOLD) 1-53 3M0062400APLATE,REFLECT 1-54 3M0107900ADOOR,LID 1-55 3M0026500BWINDOW,LID 1-56 3M0011100ACASE,LEAD 1-57 3M0010400ATORSION SPRING,CASE I 1-58 3M0108500AKNOB,REC LEVEL 1-59 * 3M001340 NUT,VR M9 1-60 * 3M001350 PLAIN WSHR,VR M9.1 1-61 3M0109300AHOLDER,REC LEVEL 1-62 3M0108900AWINDOW,FLT 1-63 3M0107800AFRONT PANEL 1-64 * 3M0060100APLAIN WASHER,M3 D11.5 1-65 * 3M0117700ASHIELD PLATE,IC 1-66 * 3M0115700ACUSHION,GUARD 1-67 * 3M0116500APLATE,FCC GUIDE 1-68 * 3M0115400ACUSHION 1-69 3M0062700ARTNG RING-C,D7.7-0.8 1-71 * 3B0001806ASCREW,J,S M3X6(BLK) 1-72 * 3B0005708ASCREW,BPB M3X8(BLK) 1-73 * 3B0005408ASCREW,BPB M4X8 1-74 3B0001306ASCREW,J,S M3X6 1-75 * 3B0000808ASCREW,BPP M3X8 1-76 * 3B0000004ASCREW,BPS M2.6X4 1-77 * 3M0010700ASCREW,4X1.3S 1-78 3B0007206ASCREW,BPA M3X6 1-79 * 3B0002308ASCREW,J P M3X8(BLK) 1-80 * 3B0007300ASCREW,FPS TITE M3X6 1-81 * 3B0000810ASCREW,BPP M3X10 1-82 * 3B0004408ASCREW,BPS M3X8(BLK)US,C,GE EXPLODED VIEW-2 12 1 2 3 4 5 6 7 8 9 0 q q t y u i o df g h j k l ; z x c b m / ! # % October 2000 INSTR